IMR

Пікірлер

@thecritic8318 21 күн бұрын

Did you rvt the seal ?

@Kado244 Ай бұрын

Did you ever complete the swap?

@jeffalleshouse9783 Ай бұрын

Parts zilla has new oem

@somethingoutdoors1412 Ай бұрын

It's a no for me due to the manual dump.

@mrbronco2 2 ай бұрын

Try 91 Octane. 6.2 recommends 91 not 87

@seap9570 2 ай бұрын

Nothin like back country riding with a wheelbarrow only in Canada

@user-in5ff4mu4k 2 ай бұрын

Do you always drive that fast? Maniac

@dylanmunt4787 2 ай бұрын

How wide is this unit

@howardkettner 3 ай бұрын

Just got a twin to this today. Have you run into any major issues!

@IMRgarage 3 ай бұрын

I haven’t used it much ! I need to pull Engine and do the clutch and I will do the exhaust intake manifold . Do both you’re steering clutches work ?

@fnafplayer6447 3 ай бұрын

Give it some ls3 heads and people tbink it has a corvette engine.

@IMRgarage 3 ай бұрын

She has a TVS 2300 on her now at 7psi she’s parties a bit better :)

@rayjay1901 3 ай бұрын

Rather than scoop out by hand what won;t dump out by itself, I simply grab the dump handle and work it back and forth to kinda bounce the remains out while it's in full dump position. That works great for me. I also onder about using the forward inertia of the machine as it comes to a full stop to help flip the dump forward? But there would need to be a cable and lever hooked up to the dump release mechanism that would have to be up on the handle bar to enable this.

@rayjay1901 3 ай бұрын

Ive had mine for a few years and I've had issues with the clutch handle bending/breaking twice so far. The handle is made from stamped steel and eventually gives out after awhile due to such a strain on it and weak design. Princess Auto can order you a new one but supply of them can be spotty so my advice is order one (or two) before you need them, because mine was down for mths while I awaited a new one. But they are cheap ,both in cost and design, and I just replaced it again. They are also tricky to replace due to a fairly complicated design that has fastened to the machine handlebar by bolts that run up though the left side brake control bracket on the underside of the handlebar.

@headhunter257 4 ай бұрын

I'm thinking of making a track machine for kids with this.

@prof.8674 4 ай бұрын

Dear, is there a beering in side around a culmen??

@stevenjones1959 5 ай бұрын

Would you still do it if it only has 1 of the holes?

@nicolasbouchi-lamontagne3959 5 ай бұрын

HI i was planning to do simple adaptation on a GME Rascal F10A looking for some informations to put a G16BB or something else if it's not too complicate... Just looking how to do it ?

@cvz8849 5 ай бұрын

Thanks Man!

@superlowian 5 ай бұрын

when the primary closes, the belt moves towards the engine

@dennisvilla24 5 ай бұрын

What other modifications did you have to do there than adapter harness

@boardin7979 5 ай бұрын

My nytro broke down yesterday in the driveway, thought it was the belt at first... Shouldn't I be able to turn the primary by hand? thanks

@IMRgarage 5 ай бұрын

One way you should be able to . There is a gear reduction there that makes it hard to turn !

@boardin7979 5 ай бұрын

@@IMRgarage thanks man.. I just fixed the ski and installed a new battery.. then went for a test ride, got about 20yrds then a pop sound happened with a little smoke. when I tried to start it again, nothing would happen, seemed like the primary is stuck so the engine won't even turn over

@ConfusedBabyTurtles-ul4uq 5 ай бұрын

How t repair

@guntherpetutschnig2705 6 ай бұрын

Handsame machine

@ChadMc74 6 ай бұрын

its basely pretty nice

@user-nu5qr6wh7g 7 ай бұрын

🥱 ssslow

@jacobboyko888 8 ай бұрын

I'm in the process of buying a 2015 yamaha sr viper xtx se 141 I've had a 97 vmax 700 triple sx for a long time with no issues but decided to get this newer one . What's all I should look at before I load it up and take it home . Thanks

@IMRgarage 8 ай бұрын

Check the jack shaft bearing behind the secondary , also the play on the main drive . Grab the brake rotor if she’s loose you will need to do a lower bearing and maybe a shaft . Those are prob the main things I’ve noticed on the viper . Also boogie wheels check them all depends are you paying high money for this or low ?

@jacobboyko888 8 ай бұрын

@IMRgarage ok and I consider it higher amount there asking 9000 for it can as I'm in Saskatchewan Canada. And the mileage is 7000 kms

@IMRgarage 8 ай бұрын

@@jacobboyko888 9k is on the high side with the Eccomy I would offer less for sure unless it’s supper clean .

@jacobboyko888 8 ай бұрын

@IMRgarage yea it looks to be clean it's shiny etc not dented up or paint missing so. It's red and white. I got them to order a bunch of accessories for it to. Tunnel flares the 4th boogie wheel for the back windshield bag handle bar bag rear large size storage box the yamaha gold gas cap and the battery tender that has to be installed on it . Plus a yamaha viper tarp plus the cover that goes underneath the tarp and a couple other things . I'd like to get hid bulbs for it and an exhaust but not a ridiculously loud one or one that's drony I've heard people saying. I'm the type of guy who's not hard on things I don't jump them or go in the mountains my terrain is at the farm going threw fields ditches and the odd poker derby. So

@philhugill8458 8 ай бұрын

'PRINCESS AUTO'------The pride of Winnipeg, Manitoba, Canada-------Started by Mr Tillman on Princess St with a tow truck.

@mr.tomraypaz6085 8 ай бұрын

It’s one of those Frankensteined G20 cutaway van Winnebagos. Looks like they grafted Dodge headlights into the nose!

@krampp24 9 ай бұрын

Where in canada are you located? I need work done on my speed6

@IMRgarage 9 ай бұрын

I’m located in Ottawa area you ?

@Defender7077 9 ай бұрын

Did you ever find what the issue was with this?

@IMRgarage 9 ай бұрын

Lifters where collapsing . My buddy bailed on the deal bought another one and made the same noise month later ate a lifter and cam lobe :(

@Defender7077 9 ай бұрын

@@IMRgarage I am seeing this issue very very often on vehicles I find at auction with that motor, gas it really hard at idle and it makes a nasty cracking noise

@user-tf7dn3ow6c 9 ай бұрын

Made in China?

@IMRgarage 9 ай бұрын

Pretty much everything at Princess Auto is made in china lol

@IMRgarage 9 ай бұрын

Stock ?

@NorthSideProductions 9 ай бұрын

Nice run! My 2012 mdx ran 15.42 at 90.52 mph

@IMRgarage 9 ай бұрын

Stock ?

@NorthSideProductions 9 ай бұрын

@@IMRgarageessentially stock. I removed spare tire, intake resonator, and I have an intake manifold spacer

@IMRgarage 9 ай бұрын

@@NorthSideProductions nice I want to hit a 14.00 with this thing :) doing PCD j pipe and the ported TL heads with the BC cams should be able to hit that we shall see :)

@robmotown1 9 ай бұрын

Hopefully you put a groove in the oil seal outer mating surface with your pin punch! Your technique is so smooth and not at all crude!!!

@raumantk931 9 ай бұрын

high flow third cat? which cat did you use??

@IMRgarage 9 ай бұрын

RV6 PCD and J pipe with high flow cat one piece J pipe

@ThatYoutubebloke 9 ай бұрын

Your John deere broken? A loader attachment would be far faster to use and do much more for far less cash

@IMRgarage 9 ай бұрын

24” vs 57” this is working awesome in my garage build and between trees .

@DieselRamcharger 10 ай бұрын

lmao. lock downs.

@IMRgarage 10 ай бұрын

@ProbeGT2 10 ай бұрын

I was thinking about buying this last week, glad i did not. That dumping issue and not dumping completely is a no go. Toi bad because the rest of the machine looks nice.

@IMRgarage 10 ай бұрын

I’ve got about 20 hours on it I’ll do a update video on it soon. So the dumping issue is kind of annoying but I dump and back up and the vibration from the motor helps . You usually have a bit left so I just use my hands and it empties .

@user-tu8pz3fm9l Жыл бұрын

That's cheating sir !

@brokenturtles_skateboardin4519 Жыл бұрын

I spent 2 hrs at Canadian tire looking for the right bolt to go in the crank still haven’t found one

@erikluff7481 9 ай бұрын

5/16-24 Fine thread bolt

@Flyfish325 Жыл бұрын

Replace your rubber value stems with metal values, the liquid will weaken the adhesive on the rubber value stem core and it will eventually fail, guaranteed. 😢 I just went through that with my 1025 R turf tires loaded with Rim Guard. Informative video, nice job!

@solomangrundy25 Жыл бұрын

My dad designer for this camper I worked there too in the steel shop making the frames

@IMRgarage Жыл бұрын

They built a nice trailer ! I wish they made a wet bath and bit bigger front bed but this thing pulls very well :)

@dhdh8314 Жыл бұрын

You mention the machinenis a little light in the back end. Ive seen videos of similar machines that have steps behind the motor so the operator can stand/ride. Do you think this machine could handle a rider standing behind the motor if some steps were fabricated?

@IMRgarage 10 ай бұрын

I step on the back or kneel on the back plate when it has a load but if it’s empty no she cat walks. I’m gonna do the engine swap and add the battery to rear which will add 20-25 lbs to rear might help I’ll do a video

@Hsvgts0376 Жыл бұрын

Hey mate, how did you get on in the end? Dying to see the rest of this series

@robertmurchie2363 Жыл бұрын

Absolutely scrap and dangerous kept tipping over don’t buy

@dirttdude Жыл бұрын

those things really start to shine when you have to haul 250 loads of gravel up a big hill.

@smartassist9700 Жыл бұрын

Put a double small hydraulic arm(s) under neath. Smoove operationnnn.

@abefehr6155 Жыл бұрын

I can use one I don't really need one but seeing this video I want one Seeing it goes through bush well I'd rig it up to pull logs out of the woods

@donnridgway1298 9 ай бұрын

You get one was winding the same for logs

@papabits5721 Жыл бұрын

Would make a great base for a giant snowblower

@be.ndover Жыл бұрын

that looks pretty sweet but i got a few things from princess auto that failed in no time wont get anything from there with a motor on it got the trenching saw machine thing pos teeth breaking off first trench and was the worst to control move and load returned it and got to honda lawnmowers had one of them motors fail in a month and it was a honda so i wont trust anything from there again and some motors before that i learned my lesson

@boerplaas388 Жыл бұрын

Rubbish. I’ll do the job with a push wheelbarrow ten times faster than to mess with this heavy piece of crap. This will be great for fat lazy Americans 😂

Ең жақсы KZfaq

Пікірлер