Tech Review by Irdi

Пікірлер

@Krobiiiiiii3 12 күн бұрын

I'm driving an 04 jeep grand cherokee, and intermittently the liftgate open notification pops up even when the liftgate is not or has not been opened. Would this fix help stop that notification?

@TechReviewbyIrdi 7 күн бұрын

There is a signal wire in the deck lid. I would imagine it's either a broken core wire there or more likely it's up towards the wire by the hinge in the rubber protection area. It's normal for this age and happens to a lot of them.

@romeousprimeruno 12 күн бұрын

You are a life saver!!! I just did exactly what you said & saved myself at least $200 on the part & more on the labor for only $26.99 ordered my part on Amazon. -Much Appreciated

@jorgevasquez-lz4be 12 күн бұрын

Very good video thank you!!!!

@coinbounty3347 13 күн бұрын

Part will be here in 2 days. Got my flathead read! Thanks man. Wish I could find the trey that goes over the transmission release though.

@bmogo49 23 күн бұрын

I installed the grip extender just fine but now the magazine holds only 9 rounds? Cannot insert 10th.

@TechReviewbyIrdi 23 күн бұрын

Recheck the spring foot. It may be edged up a millimeter or two.

@josephtompkins3199 Ай бұрын

Nice video. Saved me from shooting the base across the room on the first try.

@kennywheelus6857 Ай бұрын

also I love how smith made this one red dot optic ready too.

@kennywheelus6857 Ай бұрын

Thanks for for pointing that out,in all the gun reviews don't show it like that when you reset it to hear it,so now I'll know when purchasing this one,I have the older little brother the performance center m an p 9mm shield ez,I love that little pistol,I've had mine for 2 years now,but a year ago or so I saw when smith came out with this,the only downside on the performance center was the one married single stack 8 round,which is ok for home defense or conceal carry,but I like to be able to carry a few magazines that hold more rounds rather than carrying too many magazines that only hold 8

@TechReviewbyIrdi 26 күн бұрын

I like to hear that. This Equalizer is my go to now. I've got this one honed in beautifully. I've been shooting it more than anything else I have. Even my Single Action collection.

@kennywheelus6857 26 күн бұрын

@@TechReviewbyIrdi , awesome

@redemption7449 Ай бұрын

Is there anyway I can remove the matte finish off my revolver?

@dnyboi7659 Ай бұрын

This optic is a direct mount to the equalizer?

@TechReviewbyIrdi Ай бұрын

Yes. I run it all the time and it's great. But you need screws for the S&W threading like in the videos.

@dnyboi7659 Ай бұрын

@@TechReviewbyIrdi awesome thanks, just bought the holosun, waiting on the screws now, did you use vibratite and a torque screwdriver to install?

@romerolilianna Ай бұрын

Thanks

@shroomz3066 Ай бұрын

Hell yeah thanks brother 👍👍👍👍🙌🙌🙌

@CHAOSMOVEMENT Ай бұрын

my throttle body is mounted horizontally (5.7L)

@TechReviewbyIrdi Ай бұрын

Use the straw version, there's one with a U-shape red and black straw for horizontals. Then clamp loosely the air assembly over it.

@pharmis Ай бұрын

great video! appreciate you taking safety serious, good model!

@bradlybaldwin9564 Ай бұрын

Hemi tic is a result in not changing your oil every 5000 miles.and not using 40 weight oil

@JohnWicwikki 2 ай бұрын

Thx

@kurtislowe6749 2 ай бұрын

Great video .i have an m01 and a shield plus. You may have just saved me some money if i can get them to match up.

@libmananchannel 2 ай бұрын

Hello, Tech Review by Irdi! Thank you for showing us such a great video! I feel very happy! Looking forward to your next work! Have a nice day!

@philipsifuentes8971 2 ай бұрын

Preciate the help

@sialepuailoa4542 2 ай бұрын

5 years later watching this today and getting the part order to do the easy fix that took me no longer than 5 minutes. Thank you so much and your time to make the video because it was a huge help and definitely a money saver 🙏

@TechReviewbyIrdi 2 ай бұрын

You're welcome!

@INeverMiss3351 2 ай бұрын

You the man🫡🫡 my passenger button broke and took less than 5 minutes. Got mine on Amazon for about $27 . Only think I hate about the Amazon one… is the illumination is blue instead of white 😩😩 . Other than that it was quick and easy install.

@twinbadger1 3 ай бұрын

How well will it clean the throttle body ?

@TechReviewbyIrdi 3 ай бұрын

Really descent, don't force the throttle open though. Use the straw device.

@twinbadger1 3 ай бұрын

@@TechReviewbyIrdi thanks my truck is really bogging out when I get on it

@Trickyflex6969 3 ай бұрын

Came from your drone reviews I’m impressed you really improved over the years

@TechReviewbyIrdi 3 ай бұрын

Thank you. Ups and downs in life and many changes. Keep on watching, new stuff coming.

@Precocktrigger 3 ай бұрын

I like but the battery placement is a deal breaker for me

@kurtislowe6749 2 ай бұрын

Why? Every 2 years your replace the battery and check the zero on your firearm.

@christopherm8215 3 ай бұрын

What screws did you use on the shield plus the 2 that came with ny riton dont fit

@TechReviewbyIrdi 3 ай бұрын

They are from Amazon for the Shield plus, #6-32 x 1/2″ button allen screws for Smith and Wesson Shield Plus. The Riton has a flush screw area and button style tops are better. If you change it to a routed out one like Holoson, then I would go with Freedom Gorilla's cone/tapered style #6-32 x 1/2". You can go as little as 3/8" length, but I recommend the 1/2" as so does S&W for the mill depth. Use locktite blue to keep them from ever retracting. (hint-always use a white paint pen or nail polish dot on the top side of the screw and one on the body of the optics to make sure it stays torqued-just a little dot across the gap-like an indicator mark).

@rickmoore745 3 ай бұрын

I saw nothing here. Just a target.

@juliahusby5911 3 ай бұрын

Love my equalizer my choice of going to carry

@srallnutt 3 ай бұрын

Hi there. My micro flash has malfunctioned and so the AL619 is currently dead in the water. What do you recommend about getting hold of the software for this device! Cheers. Simon

@TechReviewbyIrdi 3 ай бұрын

I've been out of touch with Autel in the last 2 years. But I had a shop login we used that we had an account with them. I once had our guys do the same and they did send us a set of disks. One was for flashing the device, and one was updates on cars in later years. I would start with their support link to see where they can point you. Otherwise, anything on the open net may or may not be viable or riddled with spybots for downloading of a site.

@JoudyA14 3 ай бұрын

Nice video

@khairularifin7088 3 ай бұрын

Need help. Long read ahead. I have a 1988 Honda Civic EF 1.3 automatic. I got the transmission changed in May last year because the previous transmission wasn't engaging from the 2nd gear to the 3rd gear. The new (second hand) transmission was fine then it started to show some lag when put in 'drive' (when the engine was cold). I was using the original Honda Transmission Fluid. Slowly that problem got worse and I'd have to keep the car running for about 10 minutes early in the morning and only then 'drive' will respond. I was advised by a local mechanic to change to Amsoil Transmission fluid as he mentioned it has additives and I did. A) First Amsoil Transmission fluid change. It showed improvements like the 'drive' gear engaging right after I started up the car but it would only coast in drive, stepping on the accelerator didn't have any response. I'd have to warm up the engine for maybe 3-4 minutes and would be able to drive off with no issues. I noticed with each passing week, I'd have to warm up the engine longer for the drive gear to engage. The problem came back in full swing after 3 months with newer symptoms. After warming up for about 10 minutes and driving off, the engine would have to rev up to 3k or even 4k in a very struggling manner and it would sound as though the engine has to work way harder to get from the first gear to the second gear. But once at operating temperature, the transmission works just fine and smooth but it would slip sometimes. This new symptom showed up after having driven the car for about 5k miles since the Amsoil Transmission fluid change. B) Second Amsoil Transmission fluid change. So I changed the fluid again and things got better than they were towards the end of 5k mileage of the first Amsoil fluid change. I drove another 5k miles and have another new symptom. The reverse gear won't engage when the engine is cold. So I'd have to keep the engine running for about 5 minutes for the reverse gear to engage and about 10 minutes for drive gear to engage with the current trans fluid. But, in order for first to second gear to shift smoothly, id have to run the engine for about 15 minutes (reach operating temperature). 15 minutes does the trick and the car runs just fine the whole day (absolutely smooth like a new car I'd say). But if I leave the car parked for a few hours, I'd have to run the engine for about 2-3 minutes for the gears to engage. This is the current situation I'm in. So basically I have three problems: 1) Drive gear won't engage if car isn't warmed up. 2) First gear going into second struggles a lot if not sufficiently warmed up. 3) Reverse gear won't engage if the engine is not warmed up for 5 minutes. My question is: Would Lucas Transmission Fix be effective in helping me with this issue if I were to just top it up with current Amsoil Transmission fluid? Any help that comes my way is very much appreciated. It's the only car I have and I absolutely love this car. Thank you so much.

@TechReviewbyIrdi 3 ай бұрын

That sounds like the seals and expansion to heat issues. If it catches once heat starts to warm the fluid, viscosity also changes with the expansion. It's really the seals doing this. The seals within the transmission have hardened where they leak until things inside the transmission heat up and expand and then the transmission shifts normally. The reverse is separate but shares the seals on that side. Catches differently until the seal expands. It's usually a rebuild with new seals.

@khairularifin7088 3 ай бұрын

@@TechReviewbyIrdi I see. I guess I don't have much of a choice than to do a proper repair on it. Thank you so much for the very detailed explanation. I really appreciate it. 😊👍🏼👍🏼

@abnercordero7093 4 ай бұрын

Good Job!!!

@kiwihans100 4 ай бұрын

I have a Chrysler 300C the sun roof opens but as its closing the front wind deflector doesnt quite close enough causing the s roof to open again! Is there any adjustment to make the deflector close compleetely?

@TechReviewbyIrdi 3 ай бұрын

Not that I'm aware except the install screw locations. Try reseting everything with the battery. The body controller by be set at a shorter range.

@RiddledEnigma93 4 ай бұрын

Ok so the barrel cable lock was included in the package as well, I thought it was a actual accidental toss in or something.

@peterf4552 4 ай бұрын

The Maverick 88 is probably the best shotgun value out there. It's basically a de-featured Mossberg 500 that costs half as much as a 500 (and about a third as much as a 590). I'm waiting to see if Mossberg makes a Retrograde version of the Maverick 88. 😁

@Ty-nb5mi 4 ай бұрын

Gonna try this on the 2019

@daveerrington5166 4 ай бұрын

This is a trans fluid change. Not a flush.

@Noname111-u7r 4 ай бұрын

I have a 2022 Grand Cherokee and when I press the close button it only goes into vent. The sunroof does not move back. And the sunshade does not work. Do you have a fix?

@TechReviewbyIrdi 4 ай бұрын

You can try discharging the vehicle(actually the body controller) by disconnecting the battery for around 5 minutes or longer. That would be where I would start first. They get into these glitches after some time. There will be a lot of new things that will happen like throttle response comes back and so forth. Your uconnect may take a few minutes to reset itself as well.

@huntergordon6222 4 ай бұрын

Only my passenger window works. The driver door controls don’t work at all and my rear windows don’t work even with their own controls. I was fooling around with the side mirror adjustments on the driver door control and when I went too adjust the mirror it turned off the radio and still didn’t work. I have a 06 charger rt Daytona top banana

@Debbie_T_FL 4 ай бұрын

Thank you for your video. I just bought the Equalizer. Haven’t shot it yet. I’m having a terrible time pulling the slide off without touching the grip safety with my arthritic hands. I’ve tried both ways you suggested and it’s very difficult. Does it get easier as the gun breaks in? Any other suggestions?

@TechReviewbyIrdi 4 ай бұрын

Yes, it does get easier. I've gotten into a new hold to release the slide without touching the back. I sandwich them with the business end down. the slide parallel. My left goes down, my right goes up. I'm cupping the picatinny rail and trigger guard with the right. And I'm holding the front sight and serrated edges with my left.

@TalkMyShiit 4 ай бұрын

Mines just went out and will grab the part and make the swap. (2012 Dodge Charger RT)

@ryanhatzenbeller1649 4 ай бұрын

can you cowitness with the stock irons and the holosun 407k?

@TechReviewbyIrdi 4 ай бұрын

It works. It's 1/3 co-witness. The 407k has a decent rear cutout and wins over most out there. in height allowance for sight view. The front sight is normal in height and the rear is 1/3 in height. I've had a few and have only looked for ones that can do a full Co-witness. Not too many red dot bodies will do a full on the micro 9's or even this bigger Equalizer. But the Equalizer is set as a combat-hold for the front sight for point-of-aim targeting. Meaning the front sight is better over the point of impacted target. You can look up the different co-witness versions. The three are No Co-witness, 1/3 Co-witness, and Full Co-witness. Sight change would get you a full co-witness, but the 1/3 works very well for this handgun.

@user-px5he2np5u 4 ай бұрын

Mine is leaking so it's the seal?? Thanks for helping

@TechReviewbyIrdi 4 ай бұрын

Usually. The fluid over time as well as heat shrink the seals enough to leak.

@abaddon-1172 4 ай бұрын

Thank you!

@teddbrooks216 4 ай бұрын

Thank you 🙏🏿

@OGCaptainGrunge 4 ай бұрын

Whats the exact reason why it wouldn't work on a 13rnd mag?

@TechReviewbyIrdi 4 ай бұрын

It's the clips retention and plate. Could be modified for the step. I tried though.

@intothewild9282 4 ай бұрын

Don't need all that grease on the axle. It will just contaminate the diff fluid.

@diezelvh4133 4 ай бұрын

The 20-inch 88 is like my favorite shotgun ever. Light, less recoil than a heavy 870, and reliable as a Honda Civic. And 7+1 rounds!

@ahyungrocks5509 5 ай бұрын

Great video. Will do the same for our Odyssey.

@rds479 5 ай бұрын

I wish smith would have made this full ambi

@ic3Qu33nLounge 5 ай бұрын

Hi I just want to say thank you for your video! I’m a gals that does not know much about cars and I recently got a Jeep of the same model and I’m working on it by myself. I changed the lift gate actuator all by myself thanks to your helpful video. So thank you very much for the step by step instructions on this guide.

Ең жақсы KZfaq

Пікірлер