Another useless video. Most blinds are stuck up on the window and attached to mounting. You can’t just ‘pull the entire blind off and pull off the end ‘. Why do you ‘experts’ never show how to replace a chain to a blind in situ?

was this recorded on a smart fridge

GREAT ❤

Many thanks- this is the only video I've found that goes through how to install a motor into an ordinary blind. I bought some made by another company (sorry! but I'm in the UK so no hard feelings, I hope 😀) and their instructions are total rubbish. I now know what I'm doing.

Thank you so much sir

Hi Mike- are these custom curtains ? is there a link that you can share with me? Trying to achieve this look for a client and have struggled in the past.

If only they weren’t RF.

When measuring for a T-post I understand that it’s measuring from left to the middle of the post but I’m unsure of how to know where the T post would sit. For example, if it is 1780mm wide window and going 3 panels with 1 panel, T post and then 2 panels. Would I divide the 1780/3 to make each panel approx 590mm wide each and then measure left 590mm plus half a T-post width? I hope this make sense 😅

I already have set up automate roller blinds with remote last year. Now I want to buy a hub to connect to the app but not sure if the motors are compatible . How would I check the motors I have can connect to the hub?

5 years later, still helping new people

Looks so easy when you do it but my joining link won't push onto the chain. Trying with pliers. Still no good. End chain ball keeps breaking off.

These look great. What a system. Do you know if these would integrate with Home Assistant or Apple HomeKit?

Thank you

Available in US?

Great video! I fixed my sons blind effortlessly with your help. Thank you.

Do these rails hold heavier curtains too?? 😊

Thank you from Scotland and from a complete novice DIY'er. Liked your video, big handsome guy.

Great video - doing this tomorrow and joining two tracks Thanks

Saved mate bought a new blind give it a tug and the chain dropped off LOL couldn't figure out how to get the bugger apart to put it back on you solved my issues . Thanks Aussie here :)

Thank you! 🎉

great advice thank you very clear to understand

how about if I have a "popcorn" ceiling? is it as easy? Do I need something different? It's a 70s building,

My roller blind is to tight to pull up,what do I do?

What side should the overlap panel be on

my Chain is cut. how to fix it?

my Chain is cut in the middle. how to fix it?

Chain fix for RollerBlind. In case you are here to reattach the chain for a Louvolite Shade System 40 clutch R3025, this is what you do Remove blind - steps to do this: - roll up blind (if you can with a little force, but not essential), push chain end in a direction it will move a little, usually up, push toward other end., it should now be detachable from chain end) Once removed, roll up blind if is not already Pull out mechanism on chain end from the roller tube - the whole chain enclosure mechanism should slide out - use a flathead screwdriver to ease out if necessary. Remove the plastic pin from point at the end, prise out with a small Phillips screwdriver in the hole if can't do manually Replace the chain - if it has a joiner the make sure it is placed close the mechanism on the side where the chain is chain is will drop down. Reverse process to refit. Note: the three lugs on the chain end should be faced upright, ensure blind is facing correct direction.

It worked. Thanks, Michael.

How do you measure the size for the chain replacement? What does drop size mean?

How did you pre fit the brackets?

Excellent video! I really want to motorize my blinds.

thanks, couldn't figure this out

Thanks for this it helped a lot!

Can you share the name of the packer/plaster anchor?

Where do you get this anchor? Thanks

Hi can you put a plantation shutters on a balcony french door ? thanks

Where do you get the chain joiner?

We have a big gap in the middle over the blind help

WHERE DO YOU GET THE SUPPLIES PLEASE?

This method obviously works great and looks very symmetrical but why no use of a stud finder to find the ceiling battens? Is it simply for the alternative spacing you suggest?

Thanks for your video but chain drive didn’t look like any of the ones yo showed. I had to pinch together the two ends that were on one side of the chain drive which allowed it to come apart so I could fit the new chain in. Unfortunately its still not working 100% as theres a chain joiner and i don't know how to position the chain so the joiner does reach the top of the chain drive before the blind is totally rolled up. So it rolls up 3/4 of the way but that will have to do for now.

Excellent video, Thank you.

Thankyou sir 🙏

Great video, thanks for sharing!

When using the hub can the blinds work independently to one and other?

Thanks so much for this tip. Couldn’t move the blind but now it’s off and ready to be cleaned. Top video.

Nice job. A pity the previously asked questions have not been replied to.

Fantastic video. Were do you get the Mikes recommend plasterboard wall anchors??

That was a great video! Super clear and informative. Thank you!