hi, you really need to contact Ghost White Toner. But I'm sure if this printer is on their website, then the B-Paper PRO will work. If not in the Ghost White Toner offerings, then tests would be required to see if the printer works. of course, you are only printing on the A-Foil and not the B-Paper PRO, so if a transparency option is available and white toner is also installed, then most likely. But, no guarantees, testing is required.

@@forevertransfers ok fair enough. I will do some testing...it's worth it to try

Hi, you can use this link to find an official FOREVER Dealer: bit.ly/Find-My-Dealer

Hi, you can get more information from this form: www.forever-ots.com/contact/forever-dtf-premium-matt/

Hi Bilpat5123, sounds like you're having some heat press issues. You need to check you pressure and temperature. you can use a digital heat sensor to check if the temperature of the heat press is correct. and as for the pressure, there is a little trick to see if you have the right pressure setting - you open the press and place 4 pieces of paper on each edge, close the press and if you can remove them pieces of paper, then you are not using enough pressure. if, on the other hand you pull and tear the paper, then you are using too much pressure. you should be able to pull the pieces of paper, so they move just so slightly, without tearing. Once you have each of the pressure and temperature settings set up, the all the problems you mentioned will disappear. Assuming you are using the correct transfer settings, which we mentioned in the printing instructions. obviously, our settings are a guide and each person, heat press, and country of the world has their own humidity settings. so please test.

@forevertransfers hello, thank you for the detailed response, I am using the hotronix fusion heat press so they are pretty accurate, after trial and error the only way I overcame this issue is by lowering the temp on the heat press. The guide says it needs to ve about 150-155degrees c to marry A paper to B paper, I have to dial it back to 145degrees Celsius to get better results, I am not sure if this will affect the longevity of the print??

If you have ideas for future content, please let us know.

Laser-Dark (No-Cut) works with both. But with CMYK, you can’t print anything. You can only print full tone colours. No pastel or light colours will work with CMYK. 👍

Thanks!

Hi Steve, we use the Matt Finish paper (from Forever) because we have had better experiences with it and we like the end result better.

That's right, thank you! 🙏

Go get it! bit.ly/Find-My-Dealer

No. This is a ceramic or hard surface transfer paper. But for paper, card and book covers you can use our FOREVER Laser-Dark (No-Cut) with Hot Stamping Foils. www.forever-ots.com/product/laser-dark-no-cut-cmyw/ www.forever-ots.com/product/hot-stamping-foils/

This episode happened a while back on our FOREVER US Instagram channel. This is a cleaned up version of this video. More videos like this to follow. We hope you enjoyed the content.

​@forevertransfers hi, does forever have a definitive solution for white flecks adhering to A-Foil in non-toner areas after marrying A+B. Using forever laser dark low temp. Upon transferring to fabric, some of the white-toner design was ripping off the shirt and staying adhered to the A-Foil. Recently encountering lot of residue off the B paper sticking to A paper on blank spaces... thus ruining a print. Appreciate it @forevertrnsfers have a solution.

I wish they would answer this

I guess it depends on where you’re getting your glue, how you cure it and if you control the humidity - Then b-paper pro is pretty great. More stretchable, better colours and higher washability as the previous version.

@@forevertransfers Where in Europe can you buy FOREVER B-Paper PRO? Poland, Slovakia, Germany, Ukraine?

A laser printer and in this case a white toner laser printer.

What better systems are you referencing? I'm on the hunt