Most likely a wrong DIP setup. Contact our team at [email protected] if you purchased the kit from our company.

Hello, CarsGadget is online store only, we don't do installations. Try Best Buy Geek Squad in your city, they do installations of our product.

What brand of interface you installed?

it works with 2011-2017 Audi with 3GMMI radio. As long as your 2011 A8 has an AUX-IN or AMI slot in the armrest.

Yes

Sorry don’t have that.

No? Doesn't need soldering, I wouldn't even recommend soldering for car wiring but you do you 😊

Hi, if it has same dashboard like in the video then yes. If it’s a restyle it will not

Where can I purchase this?

No need for that. One unit with CarPlay is enough as it provides both.

@@CarsGadget is it possible to have 2 mmi’s installed? Because I got the CarPlay mmi and and back up camera mmi ordered

@@alyanabeltejar4538 you just need one. CarPlay MMi as it has a camera function built in.

using the mercedes decoder

No need to connect it to reverse light

@@euosnix Our kit doesn't require to do any coding. It's plug-and-play.

the seller who sold me rear camera tell me i need cut white wire, because i use 1080p camera if i cut the white wire the camera runs in 720p, and camera will show, you agree with that?@@CarsGadget

Need to connect provided AMI cable in to the glove box and select AUX/AMI in the Media menu.

same issue here !!!! looking for tips

@@andregiroux4282 I managed to do it after 2 days and almost loosing my head. From all that I read, what worked for me was to cut some of the elastic tape that wraps the car cables in the thick harness. This allows to free the cables as the big problem is the thick harness that has no flexibility and prevents the MMI unit to slide all the way to the end. After freeing the cables as much as needed, I arranged them so that the quadlock connector would be on the left hand side and slide it to the end where there is a hole that allows to place it underneath the MMI unit. Since the cables will be a lot more free, the quadlock connector can be placed there even before connecting the rest of the cables to the unit (having small hands will help with this). If the cables are well arranged, the unit will slide to its place without even forcing it. Good luck with this endeavor, I almost quitted in desperation, but the final result is great!

@@toscano88 OMG thank you for this !!! funny enough I had started to cut that weird slippery tape to be able to move around the big sturdy quadlock wiring but stoped as it exposed wires, but I will keep going ! so left hand side, bottom/under the MMI....thanks for this, will keep you posted here. I even broke a wire off the connector in trying to do this as I probably was too violent with the wires !!!!! just a scissor I guess ?

@@toscano88 also you mean cutting the tape from the harness coming from the car ? the unit's Y cable ? both ?

Yes, a simple scissor will do the work, but be careful not to cut any cable its rubber to avoid exposing the wires inside. I'm not sure about the Y cable you mention, but I guess the rubber tape can be cut from any cable you want to free.

Yes

You have not connected the power plug to the handle properly, Reconnect the connector.

Same, did u ever figure it out?

in automatic transmission cars, there is a CAN bus signal saying this is happening. In manual transmission cars, you have to use the additional optional wire like in the instructions

I’m having the same problem. Did you figure it out?

You have to plug the cable they provided to the box inside the glovebox

There's tow clips that you need to take him up and then push the radio inside , I ran into this too, I was working in the dark until I realized that it interfered from behind and it didn't sit well with me, it took me a while , Two such hooks that need to be lifted up, when you insert the radio they fall and catch it, exactly where you put the screws back, if it is lifted the radio cannot be pushed back