Пікірлер
@atriusvinius319 Күн бұрын
Is your hobby over?
@muteFPV Күн бұрын
Hello! I barely have the time to fly a whoop once in a while but I don't want to quit completely. Not sure when I will be able to get back to testing stuff though...
@user-xd5hk7od5b 11 күн бұрын
So, I have a question: How do I disabled the LED when I don't need it? =_=
@muteFPV Күн бұрын
Hello! I doubt those power pins on the board can be switched off. You would have to wire a small switch or pushbutton to the power cable of the led rings...
@mappleman26 18 күн бұрын
Is it possible to change the color of the lighting kit ?
@muteFPV Күн бұрын
Hello! I haven't looked recently but there were no multi-color-LED options last time I checked. If you need a specific color that is not available (when I made the video I think they had blue and white only), you would have to desolder the stock LEDs and solder your own, which will be a very tedious task.
@hx4011 20 күн бұрын
Such great work! Thanks man!
@muteFPV Күн бұрын
You're welcome!
@UgurOnderBozkurt 21 күн бұрын
I've bought same model because of your review and microcosmos videos :) thanks.
@muteFPV Күн бұрын
I hope you enjoy it as much as I do!
@UgurOnderBozkurt Күн бұрын
@@muteFPV thank you! I'm partly blind. it also helps me for daily stuff sometimes. I'm 51 years old. i lost my vision 10 years ago. since than i couldn't solder etc. but these days hot air solder, microscobe and other stuff helps me back to the stage :) i like vintage 8bit computers. I'm lucky that they are bigger pcbs bigger items on it. easier to work with them with these tools. HDMI out is also great for big monitor and OBS. there are many better models out there but of course they are expensive. I've paid 135 usd (4500 Turkish lira) and I am happy. thanks again i have a quick question if you know it. when i connected HDMI, internal screen goes off. do you know that is it possible keep it on while HDMI connected to external monitor? thank you
@StreetFighterStudio 27 күн бұрын
☆☆☆☆☆
@SirBernoulli 27 күн бұрын
can these motors work normally with 2S battery? thanks in advance
@JanGorales Ай бұрын
Great video, thanks for it
@rahul-ou2od Ай бұрын
Plz reply ❤❤❤❤❤❤
@rahul-ou2od Ай бұрын
Plz reply in another video
@rahul-ou2od Ай бұрын
❤❤❤❤
@rachaelb9164 Ай бұрын
Great instructions but the AI monotonous voice is so hard to listen to. Maybe I’ll rewatch it with closed captioning on mute.
@muteFPV Ай бұрын
Thank you! You are right, I agree that it sounds far from natural and pleasant. I was experimenting and it was the best result I could get back then (with a paid service, the free voices were even worse!).
@SergioLopez-vu5lv Ай бұрын
is is the same for ag01 gimbals
@meisievannancy Ай бұрын
I use freecad but Tinkercad is so much easier to use on many objects where in Freecad one has to redo due to its Topgraphical Naming problem and can be very tricky.
@HonourAmongThieves Ай бұрын
Thank you! My girlfriend drop my controller and the throttle was flopping around all over the place 😅
@jorditrillotoro2040 7 күн бұрын
same here, I tought it was broken, like my heart... because I have no girlfriend, but I least now I have throttle
@danieldewindt3919 Ай бұрын
Nice comparison Thanks for sharing 🙂
@muteFPV Ай бұрын
Thanks for watching!
@sabitbagirli7399 Ай бұрын
I tried these motors with 4 inch props and they gets super hot after 1-2 min fly. They fly very smooth but got very hot. Is it anyway ok to fly them on 4 inch props or not?
@muteFPV Ай бұрын
They were intended for 3" and 4" but it depends on so many things (number of blades, pitch, tune, overall build weight etc). Did you get them brand new?
@sabitbagirli7399 Ай бұрын
It weights 530 grams. I have used several props 3 inch and 4 inch with 3 and 4 blades. Changing props make difference but not too much. I am not good at pid tuning maybe the problem there.
@sabitbagirli7399 Ай бұрын
And yes they are new
@mappleman26 2 ай бұрын
Underrated ……… content !
@OtterFire 2 ай бұрын
where is our silent brother?!
@muteFPV 2 ай бұрын
Hello! Alive and kicking but terribly busy :(
@rahul-ou2od Ай бұрын
@@muteFPVplz reply ..website to know distance that an Fpv can cover
@muteFPV Ай бұрын
rahul what do you mean? the rc signal or the video signal? what kind of website are you looking for?
@rahul-ou2od Ай бұрын
Plz reply @@muteFPV
@rahul-ou2od Ай бұрын
I will give you $5
@benjaminscott1927 2 ай бұрын
I have to know, how did you make your switches look that way on the TX16S? The one with all red accenting. I have been trying to find somthing like this for months. And you have exactly what I am looking for.
@muteFPV 2 ай бұрын
Check my TX16S mods video series, you will find plenty of ideas for your radio, including my switch covers (they were made by Hawk Creations / HawkRC)!
@benjaminscott1927 2 ай бұрын
@@muteFPV thanks a million
@prov418 2 ай бұрын
Wow! I've never seen a vtx review done so well. If only they were all like this, we could get the most out of our gear. Thank you! I'm installing this vtx on a little plane.
@muteFPV 2 ай бұрын
Thank you very much for your kind words!
@javierrflores 3 ай бұрын
Great content!
@muteFPV 3 ай бұрын
Thank you very much!
@martinmacko7297 3 ай бұрын
by any chance VTX table for BF?
@muteFPV 3 ай бұрын
Hello! Please check the TBS data here: www.team-blacksheep.com/vtx-table-for-betaflight.txt
@martinmacko7297 3 ай бұрын
@@muteFPV but is it valid for v1.0 too?
@RazvanSecu 3 ай бұрын
Would like to see if switches can be added to the jumper t20
@muteFPV 3 ай бұрын
I don't think I will get my hands on that one, sorry!
@user-qt2tw3ob4t 4 ай бұрын
What tools or materials do I need to change from mode 2 to mode 1?
@muteFPV 4 ай бұрын
If your radio is exactly like mine, you will need to disengange the self-centering on one stick and engage it on the other stick (check @ 1:02)
@AudioVideo_IT 4 ай бұрын
Very good comparison with very similar results
@muteFPV 4 ай бұрын
Thank you!
@mitchellwilson12354 4 ай бұрын
Thank you for showing how to do the current calibration! All of the other videos I found didn’t show how to calibrate the current. I actually have the M9 but the process is basically the same.
@muteFPV 4 ай бұрын
I am happy you found it useful!
@NorgeSquad 4 ай бұрын
Actually this is sick! Orange is an underrated color
@muteFPV 4 ай бұрын
I totally agree! Sadly there are not many options and color-matching different orange parts is hard.
@NorgeSquad 4 ай бұрын
@@muteFPV Yes. but thinking the Logo is Already orange its a good match!
@NorgeSquad 19 күн бұрын
Do you have a link for the Orange Switch nuts?
@ericseidel4940 4 ай бұрын
should mute the crappy music.
@muteFPV 4 ай бұрын
Can't satisfy everyone's taste, you should try it yourself and find out if it is easy or not. Until then, feel free to turn off the volume on your device, all the information you need is in written anyway.
@mahmud367 4 ай бұрын
Are the throttle and aileron gimbals the same? Meaning do i order 2 of the same gimbals and then mod it to have no spring for throttle or are they seperate?
@muteFPV 4 ай бұрын
It has been quite a while since I last looked into these but yes, they are both the same and you only engage/disengage the self-centering. There used to be a different gimbal with less throw (travel) for the throttle stick, if you want such thing make sure to order 1 standard and 1 for less travel, otherwise get 2 standard
@mahmud367 4 ай бұрын
@@muteFPV Thanks for the reply. Appreciate it.
@davidwelch3 4 ай бұрын
Do you know where the little foam piece goes to help with the light bleed? Thanks!
@muteFPV 4 ай бұрын
Do you mean the "LED Foam Spacer" Radiomaster has on their website? Or does the gimbal led ring set now come with foam pieces?
@RedFitnessOficial 4 ай бұрын
Witch one is better? A3 or E4? Thanks !
@muteFPV 4 ай бұрын
A3 performed better in this specific test
@RedFitnessOficial 4 ай бұрын
@@muteFPV thx !
@GOOD-ss1dq 4 ай бұрын
Plz tell me about website in which I can know about - Range of a flight controller Frequency of a controller PLZ REPLY😅😅
@kl152ci 4 ай бұрын
Nice!! As much as I appreciate Bardwell and his knowledge, I was looking for his (much longer) video on this, but found this instead... Now i'm done in a couple minutes instead!!
@muteFPV 4 ай бұрын
I am glad you found this helpful!
@b2fpv 5 ай бұрын
what about A30? I already ordered the A30 connectors to replace my ph2.0 on all my whoops and batteries i'm just getting concerned after this if i should've gone with gnb27 instead
@muteFPV 4 ай бұрын
I wish I could give you any feedback but I have not tried or tested the A30 connectors
@smokehead5318 3 ай бұрын
@@muteFPV Can You test BT2.0, gnb27 and A30 please? I am waiting for Your video :) What do You think?
@muteFPV 3 ай бұрын
it is on my to-do list if I get back to making videos :)
@smokehead5318 3 ай бұрын
@@muteFPV you do such an informative content in the best possible way without unnecessary talking :) do not give up please
@muteFPV 3 ай бұрын
Thank you very much!
@tinocarnio9505 5 ай бұрын
good morning, I have a problem. I connected a voltage higher than 12V to the charging socket by mistake. The TX16S MKI doesn't turn on anymore. Will it have to be thrown away? Or is there a way to fix it? Thank you
@muteFPV 5 ай бұрын
I am not familiar with the exact circuit limitations inside the TX16S, it has reverse polarity protection for the batteries so maybe it has some overvoltage protection as well (hopefully). Please contact Radiomaster tech support directly, to get the most accurate reply and guidance.
@emmanuellamvu5010 5 ай бұрын
I wish I could do this but it seems so confusing
@muteFPV 5 ай бұрын
It is a fairly easy mod and the battery life improvement is massive, let me know if you need any help
@emmanuellamvu5010 5 ай бұрын
@@muteFPV I have the nessary batteries but not the 3D printer or sauthering machine. Do you know what type of services would do this for me?
@muteFPV 5 ай бұрын
It will be easy to find a local business / hobby shop / person to print the design for you, it is an easy print and should not cost much. As for the soldering iron, it is an absolutely necessary tool if you are into this hobby, so I would suggest that you get one (preferably with adjustable temperature) and begin practicing.
@emmanuellamvu5010 5 ай бұрын
@@muteFPV if I buy all the necessary items could we FaceTime and you give me a step by step! :))) please hahaha god bless
@muteFPV 5 ай бұрын
Sorry I don't have the time for that. I believe you will find all the information that you will need in my video :)
@leomatis_ 5 ай бұрын
will it work with 15A fuser? better/worse?
@muteFPV 5 ай бұрын
Aside from the current rating of the cables you use when wiring the adapter, I doubt that your car has such a high current fuse for the cigarette lighter. Does it? I think usually it is around 8A
@leomatis_ 5 ай бұрын
@@muteFPV no idea tbh. I just saw a few car lighters with already built in fuser and 12awg cable so I thought to just get one of those and add the xt60 connector. Skip the hussle😂
@D-Flap_FPV 5 ай бұрын
Thanks for the video
@muteFPV 5 ай бұрын
You're welcome!
@ror-ys3qp 5 ай бұрын
what about applying the two types of lub that came with ago1
@muteFPV 5 ай бұрын
Hello! I have never used them
@ror-ys3qp 5 ай бұрын
@@muteFPV ok then state that in review but do not just ignore items in the box.
@muteFPV 5 ай бұрын
They are already applied on the gimbals right out of the box, you do not need to use them when buying the AG01 gimbals and there is not much to say about them.
@ror-ys3qp 5 ай бұрын
@muteFPV one is a grease and one is an oil.
@steve30b 5 ай бұрын
Can this be linked to goggles 2 and dji controller 2 ?
@eduardoserrano5453 5 ай бұрын
How about the female counterpart?
@muteFPV 5 ай бұрын
It is usually already soldered on the multirotor, but if you are building one yourself I am not recommending a crimped PH2.0 connector. Find out why in my video here: kzfaq.info/get/bejne/oNmTf8STutywgIU.html For footage on soldering a PH2.0 you can check this build: kzfaq.info/get/bejne/mMyZpZSEmrmqYIE.html
@craftingwithjean5599 5 ай бұрын
Very good video, taught easy to understand.
@muteFPV 5 ай бұрын
Thank you very much!
@MrJohnston123 5 ай бұрын
Your content is still awesome, hope you come back one day
@muteFPV 5 ай бұрын
I hope so too, thank you very very much!!!
@robovsesvit 6 ай бұрын
Thank you so much for excellent lesson!!!
@muteFPV 5 ай бұрын
You're welcome, I am happy you found it useful!
@riotsupercarver7467 6 ай бұрын
To understand how camera angle and drone handing interact you need to understand the geometry involved. To do that, watch this... kzfaq.info/get/bejne/f6l4n9pju6mzpH0.html
@budkraus4548 6 ай бұрын
Was wondering if you had a video for the RadioMaster Boxer? Or is the Boxer similar to the TX16S?
@muteFPV 5 ай бұрын
Sorry for the late response, never had the chance to try the Boxer :)
@the_walkingdead590 6 ай бұрын
awesome build mute. but how to bind the inbuilt frsky d8 receiver to futaba t6k transmitter?(is it even possible?), what should i configure the receiver settings in cleanflight/betaflight configurator? if not can we attach another external receiver? really need advice here thx
@muteFPV 5 ай бұрын
Sorry for the late response, I am not familiar at all with Futaba radios but you will probably need an FrSky compatible receiver module (or maybe find a brushed FC board that is compatible with Futaba)
@filippoventura1646 6 ай бұрын
What is the diameter of teflon tube?
@muteFPV 6 ай бұрын
Hello! I used the common ptfe tube for 1.75mm filaments
@aminuk23 6 ай бұрын
So basically it shows a lower voltage than actual battery voltage and it shows a higher charging amp than actual amp
@muteFPV 5 ай бұрын
Chargers need to be accurate, at least for safety reasons
@knightcreation4541 6 ай бұрын
Thanks😊
@muteFPV 6 ай бұрын
I am surprised that this video is still useful! Thank you for watching!