An excellent video overall and very descriptive in your narrative. It makes sense to me how you did it and thank you for making this video. Keep up the great work
@codybird2879Ай бұрын
Same truck but an auto. I cleaned the blue and it fired up first crank. I've been dealing with this no crank problem for 3 months doing hot shot all over the US and it's crazy how one little wire has left me stranded for hours
@gatecity5284Ай бұрын
I know right, mine was so intermittent like to drove me crazy
@geraldo.m2 ай бұрын
can you tell me how much that chain needs to be tightened
@gatecity52842 ай бұрын
Loosen the tensioner bolt push the gear ⚙️ towards the baler until snug and you should be good. But if you do the upgrade I would put a new gear on since your right there
@imagoodlistener27303 ай бұрын
Great video. Im gonna splain. Hahaha! Were you able to change the wiper arms without removing the whole knotter(s)?
@gatecity52842 ай бұрын
Yes it just take so fanagalin to get under the knotters
@imagoodlistener27302 ай бұрын
@@gatecity5284 I did it this.passed weekend. I slid the timing drum(?) over on the shaft, and boom! Tough actin tinactin.
@scottganjon68953 ай бұрын
Why are people assuming that it’s the tucker fingers and shafts that are bad. I have only replaced tucker fingers or the shaft if they were physically damaged. Missing bales intermittently is most likely other areas of the knotter
@ianmorrisseyjr.47715 ай бұрын
Same truck same year automatic transmission exact same problem wrecking my brain also I appreciate the video My Brother 💪💪💪
@allendouglas635 ай бұрын
FUZZ BIT MORE WOOD... My kind of guy!!!
@frankboothe69465 ай бұрын
Good info… Hey, i had that same lightbulb on mine ha. Found a screwin LED dusk to dawn at RK and i love it. Check em out
@gatecity52845 ай бұрын
I do that thanks
@tysonha6 ай бұрын
It sounds like a TIPM or IPM rebuild depending on the year would fix your problem they are known to get corroded and have electrical problems.
@ianmorrisseyjr.47715 ай бұрын
Thanks for info I appreciate it
@jaimevasquez95677 ай бұрын
Did you find out the problem?
@gatecity52847 ай бұрын
Yes it was a short under the fuse box on that wire leading to the starter wire
@SoyChukii5 ай бұрын
@@gatecity5284where does that wire lead to brother if you don’t mind me asking having a similar issue but my wire was just loose/ next to battery terminal
@c5manufacturing5888 ай бұрын
Hi! Thanks so much for the shoutout! We really appreciate it. Do you mind if we share this to our social media? If so, we would love to get more of your information so we can shout you out!
@gatecity52848 ай бұрын
Absolutely 💯
@c5manufacturing5888 ай бұрын
@@gatecity5284 Awesome, thank you! What is your Facebook profile username, so we can message you on there.
@LarryPrice-et6lb9 ай бұрын
Wow, that was a big load of wood!! Gonna save you some work! Nice job!
@user-ul2nn2lb6s Жыл бұрын
Great video Matt!
@gatecity5284 Жыл бұрын
Thanks
@jayrobert59172 жыл бұрын
One thing you didn’t mention can you put that tucker shaft in without removing the knotters? I need to do the same thing to my Baler
@theneweraba73292 жыл бұрын
Aye good work man. This filled all the gaps
@joseestebantreminio32132 жыл бұрын
Ver a ver este video en español
@100cesarin3 жыл бұрын
How to synchronize it or put it on time friend?
@jamesmorrison18843 жыл бұрын
Think this may help me also. My baler is not tie right side and I see the tucker fingers on mine are not same position. Thanks
@ruedaricardo2 жыл бұрын
Your operator manual should detail the procedure to adjust them.
@elenagalvan93953 жыл бұрын
Todo mui bien Ahora en español por fabor
@ericcrosco62713 жыл бұрын
Just ordered this kit last week.Hope to get it next week. Mine would bale 10 bales fine then miss 3.So aggravating!!thanks for the video
@gatecity52843 жыл бұрын
You are welcome there id nothing more agravating than a miss tying baler
@user-ot1ct1jt1r3 жыл бұрын
Нихрена не пойму
@cawacyr39202 жыл бұрын
полумесяц захватывает шпагат и подает на клюв , который оборачиваясь делает узел . если полумесяц не додаст или не захватит на большой массе от иглы вязать не будет
@manuelrios52233 жыл бұрын
Es muy bueno pero me gustaría en español
@100cesarin3 жыл бұрын
Why? Does it give me more thread on one side, like an inch or two more?
@gatecity52843 жыл бұрын
Your tension on the role might be looser on one side or the other causing slake im the twine
@100cesarin3 жыл бұрын
@@gatecity5284 tanks
@100cesarin3 жыл бұрын
Why? Does it give me more thread on one side, like an inch or two more?
@melchymia3 жыл бұрын
Hello, can l get a trancsript of this video in order to translate it faster in another language?
@Airspace123 жыл бұрын
I just started a 336 JD baler page if anyone is interested in joining. Its John Deere 336 balers on F.B.
@everantonioaltuzarmauricio34594 жыл бұрын
Porfa suvir videos en español
@jaimemoralestapia34844 жыл бұрын
Seria bueno si se pudiera ,traducir al español
@100cesarin4 жыл бұрын
😆
@brucereeves63905 жыл бұрын
Thanks for the feedback on the installation of the Tucker Finger Update Kit. We are glad you ordered it, and we appreciate sharing it with the other viewers here. It looks like we need to update our installation videos! Could you please email me directly at [email protected] so I can thank you personally. By the way, we had to change our name to Green Baler Parts because John Deere didn't like us using "JD"! www.greenbalerparts.com