Did not show how to remove the front seat headrest
@dgc8082 күн бұрын
Hi there, do you know what fitting is required to attach an air hose to the Compressor? Read online that its difficult to find out what fitting goes into the compressor to attach a air hose
@drivewaydiyer65042 күн бұрын
I’ll check it out and get back to you.
@TheGraffoe4 күн бұрын
Thank you for your helpful visual instruction.
@drivewaydiyer65044 күн бұрын
You’re welcome.🙏
@ricardosom77664 күн бұрын
I got an ac system from a donor car to my 95 civic, fan worked fine when I tested it outside, but now everything is installed it’s not working. When should it start running? When one presses the ac button? Or whenever the compressor is working?
@drivewaydiyer65044 күн бұрын
Is the system upto pressure? Has it had all the moister evacuated and refilled?
@ricardosom77664 күн бұрын
@@drivewaydiyer6504 here’s what I’ve done. Since I’m a beginner when took down the compressor it lost a lot fluid, so what did did is emptied completely, and put new oil in it. I installed everything, yesterday I tried to recharge it but I think it didn’t work. And that’s why o know the fan isn’t kicking in.
@dazzahaywood32986 күн бұрын
Wheres the low port for vauxhall corsa d is it the same place under air intake box... thanks
@drivewaydiyer65046 күн бұрын
Not sure on them, probably. Follow the pipe work round. Should be fairly accessible.
@RobertMakhura7 күн бұрын
This rubbers are they removable
@drivewaydiyer65047 күн бұрын
To be honest, I’ve never tried, I don’t think so.
@graememoran14069 күн бұрын
Thanks for the video.
@drivewaydiyer65048 күн бұрын
You’re welcome 👍
@thewhopper202310 күн бұрын
Informative, thanks for the information, it is all greatly appreciated 🤘😎
@drivewaydiyer650410 күн бұрын
Cheers, hopefully it gives people a chance of fixing it.👍
@daibolical853211 күн бұрын
Trying to decide between this one or the Dewalt version, have batteries for both and generally prefer Dewalt tools but this looks a handy bit of kit, thanks for the review 👍🏻
@drivewaydiyer650411 күн бұрын
I really like it, I live out in the countryside and everything gets covered in dust, so it’s great for cleaning the outside areas.
@rollingthunder339112 күн бұрын
Thank you bro.
@drivewaydiyer650412 күн бұрын
You’re welcome.👍
@thinwhite859314 күн бұрын
Mate we can't see what you're doing
@drivewaydiyer650414 күн бұрын
You’re probably the only one. Thanks for watching.
@grahamsouthern217516 күн бұрын
Thanks very much for this very informative and straightforward video. Very helpful indeed. Thank you for posting this.
@drivewaydiyer650416 күн бұрын
Glad it helped.👍
@ishaqfazal171918 күн бұрын
Hi there. I have an issue related to my fuel pump relay on Vauxhall 1.6 B. Engine turns over but does not start. When I remove the plastic cover from the relay I can see that it does not engage. Have swapped over the relay and the fuse box, but still does not start. Engine management light stays on. Only starts if I manually hold the metal part of the relay together as to manually engage it. Any ideas? Only possible causes are engine washed (my bad) and I unplugged the switch/plug that goes to the injectors while the engine was running. Drove fine after the engine wash. Only stopped starting after I unplugged the connector going to spark plugs
@drivewaydiyer650418 күн бұрын
Well the first thing to check, are you getting spark? You swapped over the fuse box? That would need coding to the ecu. The coil is controlled by the ecu aswell, is there any water damage there or green crusties. Check all the connections that you unplugged for water ingress. Definitely check the ecu. Do a pedal test aswell.
@ishaqfazal171918 күн бұрын
@@drivewaydiyer6504 Hi Thanks for super prompt reply. Sorry bit of a novice - how do I check for spark. Changing the fuse box didnt require any programming. Didnt see any water damage on ecu or any green. Will check connectors tomorrow. What is a pedal test? Last resort is send off my ecu to get it cloned but dont feel too comfortable with that or 100 sure how it works.
@drivewaydiyer650416 күн бұрын
@@ishaqfazal1719 to test for spark, pull out the coil, plug the connector back in. Get a test light attach it to ground and hold it close to the coil stem and get someone to crank it. See if there’s any spark
@RJ-x20 күн бұрын
thanks mate!
@drivewaydiyer650420 күн бұрын
You’re welcome 👍
@jackcool853920 күн бұрын
Hello I have a 1994 Honda Civic dx , the coolant doesn’t want to go through the hose and I already changed the thermostat and radiator and the fans also doesn’t want to kick in and when I add coolant , I don’t feel the coolant circulating at all
@drivewaydiyer650420 күн бұрын
Check for air and possible blockage in the coolant system or water pump failure. Give the pipes a good squeeze . Try flushing the system out. Is there any gasket sealer in there?
@jackcool853918 күн бұрын
@@drivewaydiyer6504 no I don’t
@jackcool853918 күн бұрын
@@drivewaydiyer6504 and my heaters turn on but there is no heat going through the vents
@drivewaydiyer650418 күн бұрын
Try flushing both the block and the radiator and make sure it’s bled thoroughly.
@malluuk666621 күн бұрын
How long those batteries are last ?
@drivewaydiyer650421 күн бұрын
I think the service date is to change once a year to be safe.
@steffen474922 күн бұрын
Thank you for this!!
@drivewaydiyer650422 күн бұрын
You’re welcome
@macdee862823 күн бұрын
On my zafira b horn itself works even though it looks as though its been rescued from the titanic i ran a direct 12 volt cable to it and it beeps :) the connections on the horn were just spade conections so looks as though its had a different horn in the past i changed the spade connections as they were rused to hell im only getting 3-4v dc then the horn button on the steering wheeel is pressed the relay is clicking away ok ive tried to short across connections as you have shown in this great clip im getting the same readings back at my multimeter looking at the condition of the wiring itself its very tarnished inside the conductivity will no doubt be poor im guessing this could be the problem ? i might even just run another feed into car dash put a push to make horn button and new wiring via a relay to the existing horn as the wiring loom looks a pain.
@drivewaydiyer650422 күн бұрын
When you press the horn, can you see how many volts you’re getting at the fuse box, if you’re getting good voltage there, then there’s obviously a relay issue or a wiring issue. Sounds like the CIM is ok.
@CFCMADFAN201326 күн бұрын
Thanks matey 👍🏾
@drivewaydiyer650426 күн бұрын
Glad it helped.👍
@DiehardSportsCardCollector27 күн бұрын
Great video. I will do this shortly thanks
@drivewaydiyer650427 күн бұрын
Thanks for watching.🙏
@davidhorvath121228 күн бұрын
Hi mate thanks for the video, i have a zafira 2007 and the revs keeps going up and down while stationary so the car is idling a little bit . Been told it could be the air intake sensor , do you think i should change it? Engine light keeps coming on and off
@drivewaydiyer650428 күн бұрын
Well firstly I’d try cleaning it, but there’s lots of reasons your car is surging, could be a vacuum leak , could be egr. Try unplugging the sensor to see if there’s any change, in performance. Do a pedal test, to see if there’s any related codes.
@DamianNoudАй бұрын
Super helpful video. Thank you!
@drivewaydiyer6504Ай бұрын
Glad it helped.👍
@Brynben1Ай бұрын
Great advice mate, thank you
@drivewaydiyer6504Ай бұрын
Thanks for watching.👍
@JohnCoote-qj7rwАй бұрын
Have you tried the T25 tool that came with it in the toolkit
@drivewaydiyer6504Ай бұрын
I didn’t have a tool kit, with it. But I have one now.👍
@GuyGuy-rq3teАй бұрын
I have a Honda civic year 00, the coolant keep decreasing in the overflow tank still my car neither overheat nor bubble on the radiator. why?
@drivewaydiyer6504Ай бұрын
Any signs of cream in your oil, check under the dash board could be a leaking matrix. Any sign of leaks from pipes and around the timing belt area?
@GuyGuy-rq3teАй бұрын
@@drivewaydiyer6504 Thank you for your reply. No cream in my oil. I have checked all the pipes and still no leak. I will check under the dash board.
@drivewaydiyer6504Ай бұрын
@GuyGuy-rq3te if no luck, then do a pressure test on the system, there maybe a pinprick hole somewhere, that’s leaking when under pressure. Sometimes the only give away is some colour from the coolant when it crystallises.
@seemaabАй бұрын
Just saw your video but you got it in low mode? You need to press the power button and set it to high mode and then try the wheel?
@drivewaydiyer6504Ай бұрын
I’ll check that out, thanks for that.👍🎉
@seemaabАй бұрын
@@drivewaydiyer6504 let me know how it goes. I just got the same one delivered so going to test it
@cyrusstothard3 күн бұрын
@@seemaabHow was it?
@seemaab3 күн бұрын
@@cyrusstothard it’s alright but not better than my mains electric one
@MrZeki86Ай бұрын
Ennyi pancserkodást össze hozni is tudomány ám
@drivewaydiyer6504Ай бұрын
Can you translate?
@MrZeki86Ай бұрын
@@drivewaydiyer6504 no worries just saying, well done for sharing
@ayanessa7879Ай бұрын
Thank you so much. This was so helpful for me right now. I am so grateful to you🙏🏽
@drivewaydiyer6504Ай бұрын
Thanks for watching, glad it helped.
@tsky552Ай бұрын
Have you changed the Relay or have you sprayed an electrical contact reactivator on it? because I'll explain, the horn works for me, but often it doesn't work when the headlights are on! sometimes yes, and sometimes no! I had already repaired the CIM
@drivewaydiyer6504Ай бұрын
Check all the grounds , they may share the same ground. Check all the obvious stuff like voltage to the connector. I suspect there’s still a CIM issue, especially if it involves the headlights.
@marcor6403Ай бұрын
I only had the screw at the end that was broken. Ended up fixing it by drilling a hole on the end of the shield at the backside and drilling through chassis. Then I used a bolt that went through the small tool compartment to the heat shield if you know what I mean. Basically a new hole/screw. I do want to thank you for your video as it gave me ideas and a better understanding how to fix this and I also as a means of prevention gave the in-tact bolts rust treatment. For me I did not need to move the exhaust out of the way. Also, 5.5k views versus 42 likes makes me sad. I hope more people leave a like.
@drivewaydiyer6504Ай бұрын
Thanks so much for the feedback and glad you got sorted. I think a lot of viewers just watch and move on , I don’t think there’s many who consider the like button. Thanks for watching
@TomasDambrauskasTimurasАй бұрын
Thanks. Very helpful
@drivewaydiyer6504Ай бұрын
You’re welcome 👍
@djruiz2857ableАй бұрын
Where can I buy
@drivewaydiyer6504Ай бұрын
The puller? There’s plenty on eBay.
@DP-ed4ndАй бұрын
My citoren berlingo van doesnt have anywhere where you can turn the passenger airbag on or off? 2019 model
@drivewaydiyer6504Ай бұрын
It’s probably not fitted with this option. Check your handbook.
@yadis5239Ай бұрын
I need help with vauxhall astra mk5 H 2007 the clutch feel free and soft any idea what would it be ?
@drivewaydiyer6504Ай бұрын
Check for leaks, drop in fluid levels. Sounds like your clutch is gone, possibly slave cylinder. Trying pumping the pedal with your hand, see if it firms up. Check for leaks first though.
@yadis5239Ай бұрын
Yes there fluid leak
@yadis5239Ай бұрын
Under the car
@drivewaydiyer6504Ай бұрын
From the gearbox or master cylinder?
@yadis5239Ай бұрын
From the gearbox
@paulrea7673Ай бұрын
Thanks baby’s got bigger
@drivewaydiyer6504Ай бұрын
They do grow 😂 mine are full size now😂glad it helped.
@vapingmatty4209Ай бұрын
You need to turn the engine on with the nozle and trigger attached to get the reading.Having the engine off won't give you a reading
@anoodono1841Ай бұрын
Thank yo
@drivewaydiyer6504Ай бұрын
You’re welcome 🙏
@gabrieltomescu4806Ай бұрын
It can also be located above the clutch pedal.( Mine Honda civic Fastback 1997)😂
@drivewaydiyer6504Ай бұрын
I’m pretty sure they put it anywhere, yours is probably a Friday afternoon build.😂
@LifeofLiamАй бұрын
This just happened to mine in exact same spot in the middle. However mines I noticed about a finger length now looking it’s about a hand length. Any idea what I should do ?
@drivewaydiyer6504Ай бұрын
Insurance job, it’s classed as part of the body structure. Very expensive and it will get longer.
@LifeofLiamАй бұрын
@@drivewaydiyer6504 is it worth the fix ? Mines a 2011. Just worried it’s gonna happen again only had the car 10 months
@drivewaydiyer6504Ай бұрын
@LifeofLiam if it’s not dangerous or leaking when raining , I’d probably leave it. Mine was a lease car, so had to repair it.
@TheJam53iceАй бұрын
Nice bunch of videos you've got, I purchased an 09 plate Zaffy the other day and I have the exact same issue on the exact same door, following this video, I'm going to check mine out tomorrow and attempt a temporary repair and then look at the wiring kit :D keep up the good work
@drivewaydiyer6504Ай бұрын
Thanks so much for the feedback, it means a lot. You can buy the wiring loom on eBay, which comes with everything you need. Definitely worth getting one of them.
@neptune59302 ай бұрын
I cant find location for my fuel pump relay in peugeot 206 1.4 8v can you help me
@neptune59302 ай бұрын
does someone know where this relay is placed in peugeot 206 1.4 8v?
@drivewaydiyer65042 ай бұрын
Have a look in front of the right hand side headlight, pretty sure it’s there.
@neptune59302 ай бұрын
@@drivewaydiyer6504 where precisely? i can't find it, i searched also near the engine ecu but nothing
@drivewaydiyer65042 ай бұрын
@neptune5930 what year is your car
@neptune59302 ай бұрын
@@drivewaydiyer6504 thanks for helping, 2003
@neptune59302 ай бұрын
2003, i'm desperate 😭 thanks for helping
@jisharchatteysseri68772 ай бұрын
Can you do a video on cruise control function.
@drivewaydiyer65042 ай бұрын
Unfortunately my model doesn’t have it😂 but I’ll consider it for a future video.
@angelamoore85712 ай бұрын
You saved my life with this video. Tomorrow i was going to the Skoda garage to find out just where the release catch was. You are a star!!!!
@drivewaydiyer65042 ай бұрын
Glad it helped, definitely a hard one to find. Thanks for watching
@abdussobur4942 ай бұрын
Cheerss
@drivewaydiyer65042 ай бұрын
Glad it helped
@jameskiets-oe5up2 ай бұрын
what the normal temp range of this car? 2007
@drivewaydiyer65042 ай бұрын
These engines run very hot, I’ll find out the exact temp.
@jameskiets-oe5up2 ай бұрын
yes, press and hold setting button on radio console till you hear a beep, then navigate using the BC button to 8th menu it should show V: OT:
@jameskiets-oe5up2 ай бұрын
any update??
@drivewaydiyer65042 ай бұрын
The thermostat opens between 90 and 105 degrees Celsius depending on what type of thermostat you have.
@jameskiets-oe5up2 ай бұрын
mine stays between 105 to 107 when idling ?
@shapoorsahil79792 ай бұрын
Hi sir! I have a opel astra h 2005 which I Chang the clutch and clutch pressure now I want bleed air but it doesn’t give me hydraulic from bleed air pip ?
@drivewaydiyer65042 ай бұрын
Could be the nipples blocked, might be worth giving it a clean out. Makes sure the reservoir caps off aswell.
@shapoorsahil79792 ай бұрын
@@drivewaydiyer6504 Thank you for your reply, I will check tomorrow, but the pipe that comes from the hydraulic tank event is not hydraulic even there.
@drivewaydiyer65042 ай бұрын
As in the grey pipe from the master cylinder?
@shapoorsahil79792 ай бұрын
@@drivewaydiyer6504 yes I mean that one pip which coming DOT4 from tank to the master cylinder then other pip from master cylinder coming to the gearbox and ther is also nipples but the pip which coming from master cylinder to the gearbox here not coming hydraulic.
@drivewaydiyer65042 ай бұрын
Hi , if there are pipes missing, you need to put them in, if that’s what you mean. The system has to be air tight to bleed, so anything missing won’t help.
@220dpk2 ай бұрын
I found same brand on ebay but in red/black colour. Is battery on yours also 1500 mAh? I see Dayplus branded ones have 6000 mAh battery
@drivewaydiyer65042 ай бұрын
Apart from wheels, been great so far.
@geoffball58032 ай бұрын
Hi, I've got a Zafira B 1.8 petrol and had terrible clutch problems, unable to bleed and reverse bleed via your oil can method, but thought it was worth trying first, so I bought the VS820 this week and this kit along with replacing the master cylinder has sorted the problem, just wanted to say a big thank you for posting your vids on your clutch problems and master cylinder, I don't think I could of done it without watching them. I bought a LUK master cylinder as you recommended and I adapted the VS820 to reverse bleed it once fitted to give it the best chance of it lasting. If you put a small pipe on the end of the VS820 Reservoir cap small tube to make it fit your bleed nipple it works a treat. So again a massive thank you for sharing your content, saved me a fortune in garage costs and I've the satisfaction and peace of mind knowing it has been fitted correctly and bled properly, just hope it lasts. cheers mate
@drivewaydiyer65042 ай бұрын
Great to see this reply, really glad you got sorted. I’ve always found this system difficult, but patience paid off. Thanks for the input too.👍👍