what resin? what layer exposure? what supports? what base layers? I've been having trouble with sunlu abs-like stickign to the bottom of the vat non stop.

It would be helpful if you worked on the fob in front of the camera lens and use more light!

Interesting, how long did the original hot end last? So far so good on mine. I print something almost everyday and want to have a replacement on hand.

are we locked into chitubox? or are there other programs we can use witht his machine?

Would have appreciated some time stamps in your videos, plus maybe a look at you setting it up the first time. Video is labelled as a first time set up after all.

This is the worst DIY video I have a EVER seen. Why would you even upload this???

I have had this printer since release and I think the bed is great. I use the school glue stick and I never have a problem with things sticking too well that I can't remove them easily. Just my experience.

What nozzle and temp settings are you using vs print speed? Just out of curiosity

Life saver

I bought the creality original recipe vacuum bags with pump, for $25, only a few out of 8 hold a vacuum. I'm looking for a better way. I live in a humid climate. thanks for this video. looking forward to the follow up.

Great video. I just replaced my 2016 Chevy Sonic fob using a $10 version on Amazon. Chevy dealer wanted $340 for a new key! I also found the following: 1) the battery contacts on the replacement fob kept falling out during the fiddly assembly, so I used a dot of superglue to hold it. The original circuit board was also loose in the new fob (as shown in this video) so a dot of superglue here would also really help you. 2) On my spring, you had to wind up the key by turning the top case CLOCKWISE one full turn. Look at how your spring is coiled, and turn it the direction to wind it up.

A helpful video for anyone trying to move the circuit board and cut key blade to a new fob housing. After going through this process I realized the original manufacturers did not want you to be able to pop open the original fob and remove the electronics and key blade. They want you to replace at the dealership for $350. (Canadian) Getting the original fob to separate takes some persistence and brute force. I started to pry the halves apart with a screwdriver but it took 2 needle nose pliers to finish the job; being careful not to damage the circuit board. Finally, if you're struggling to tension the spring, use a couple small pieces of tape to secure the key blade to the bottom half of the fob while you're winding CCW. (7:00 minutes into video) Then pull the tape off just before you snap the 2 halves together.

I have been using these for a few months and they seem great (for the price). They often don't keep 100% of the vacuum and the bag expands very slightly, but still keep the filament dry. Just a quick note - putting your Silica in the centre of the drum isolates it from the filament somewhat, when the vacuum pulls the bag in tight. It's better to have it in the filament part of the drum.

I completely broke my factory key fob. That’s was a pain. But now my only problem is the silver button does not pop out. ( doesn’t fit) 🙈 seems like the cut is different. What do I do?

How has it been printing? Any updates?

I just got my 4 ultra a week ago. Just need to make space for it. Thanks showing the set up.

I have a Mac and ChituManager for Chitubox Pro just crashes. I hate Chitubox. I hope Lychee gets the ability to send prints remotely to the printer because that is all I want here.

I have been unboxing and setting up mine this weekend. No instructions on printer set up - think it is just remove a couple pieces of film but did I miss something? As for Chitubox, yea you have to get the beta but where did you get 2.x? My thumb drive had 1.5 and does not look the same. EDIT: OK, 2.x was for basic, 1.5 is for pro. Just confusing.

Appreciate that you also looked into the chitubox card that came with the boxed set

I cannot pass the security screen. Whatever I choose, I gets stuck.

How are people getting this so early? Are you in the states

what exposure time and bottom exposure times do you use? Mine adhesion is hard to break off.

What exposure time worked out for you? I also have sunlu abs-like.

When did you place your order?

Nice! How long did they take to print? Also what resin are you using?

Your affiliate link isn't working, but great video thank you. IFixit left out the soldering portion of it.

Mine will be here Friday.. So this and the X1C combo should do me well.

Just got mine and unboxed it yesterday too! Love it! Not thrilled with ChituBox. Finding them to be a bit scammy where the free trial and subscription scheme is concerned. That bib is stupid. It does not fit. The side aprons are way to shallow to fit the machine.

Oh did you preorder it and get it already?

Please make a video video too.

How do you add an external spool if you already have the AMS Lite connected? Do I need to remove ALL the other tubes or is one enough?

Well, that was interesting... same issue. Factory keyfob appears to be ultra-sonically welded or something. What a bear!!! I tried your method and succeeded in breaking the key end off, but NO access! Would not budge! I ended up using small side cutter nippers and slicing along the seam in the hopes I could get a screwdriver in there.... nope. So I ended up nipping very carefully from the key end, very top down, then broke off small pieces so I could see the board and not damage it. Once I had the bulged part off, I worked my way down each side of the battery compartment, breaking off pieces with the nippers and needle nose pliers as I went. Once I got most of the battery ring broken, I could slip the board out. 20 minutes. Don't forget to preload the spring so the key flips out properly and fast enough. EDIT: the screw behind the chevy logo probably is there. The new one has a screw in about the same place. Didn't see it and could not find the piece after I was done to check

🌸🌸🌸🌸🌸🌸🌸🌸🌸🌸🌸🌸🌸🌸🌸

good video except its ANOTHER video without showing how to use the external spool.

I have this exact issue with my key too. I'm saving this video and buying a replacement cover. Thank you so much

Mine has a weird spring like wire, not a regular spring like this one 😪

screw under the logo on back. No need to destroy it like you did.

Video was great! $10 and 30 minutes later I’ve replaced my broken fob. Thank you!!

I literally use a Dremel and a plastic cutting bit to cut mine open.

Thank you for the video :D I am curious, did you have any problem with the bed leveling after installing it ? I have the printer for over a year and the glass bed annoyes me with small prints, because it sticks too well and I am thinking about putting a spring steel plate.

Hi, i just wanted to thank you for posting this video cause i have to move out of my apartment and was trying to pack it away but i had all this foam and didnt know the arangements to safely store it. So thanks for posting this i really appreciate it. :)

Very helpful

I glanced over the text on the thumbnail and I thought it said "How to replace a heartbreak."

U have soft perdy hands btw

I need this printer

The not so easy tutorial...jeez man..

Huge help for me. Thanks for sharing!

I keep getting anything PLA stuck. did you experience that?

I follow the steps but something goes wrong during the reboot stage. Retropie recognizes that the pro controler is connected but either abort the emulator startup or simply skips to the main screen without ever letting me configure the gamepad. Please help...

Thank you! I have changed now!❤