Hello, I have a green box in my yard and it fills with water. Is there something that needs to be turned off inside the green yard box?

I have a liftmaster the door will open once then if I lift it again it will stop in the up position and all power shuts off. In about 20 seconds it will light up again. After trouble shooting I could hear a clicking in the motor and could bump the motor and have the lights come back on. I checked the boards and couldn't see a bad soder. Any ideas.

Thanks a lot it is really useful. I salute you man👍

1:15

Lost tech - distributor points file from pre-electronic ignition in a 50s to 70s car. Try to keep the point so that they maintain contact across the whole surface. This minimizes the current density and minimizes the chance for further arcing.

Hmmm what if you do not have a striker button?

Should've oiled the bearings on the other side of the motor, too, while you had it apart.

Thanks for a very helpful video.

There's an easier way! 🤟

What does it cost?

Thank you! I just followed instructions, unscrewed both relief valves as I didn’t see any debris in #1. Upon reinstall and water turned back on, leak is gone! Will check back tomorrow. Thanks for the video!

Thank you for this. I had the problem where my garage door would just click and not move. Determined that was circuit board. My lift master is so old I had to buy a used board off of eBay but followed your instructions( good tip on color coding the wires). $30 with shipping and I’m back in business. Thank you. Subscribed.

Balancing not accurate but general idea.

thank you.. you saved me 300$

Thanks man u help me too , it's my 1st time. I am sure I will be back manytimes to this video.. 😂😂😂

This was super helpful and exactly what I was looking for, thank you!!

My preventer was removed and I don’t want to use sprinklers. How do I handle the two open holes left from the device?

Thanks bro, this helped us out. I just got back in town & the kids & wifey were taking cold showers. It works! Thanks

Thank you so much 😊

I just want to replace the motor. Where can I buy that at?

You’re a really tidy guy. It’s nine years later now. Are you still tidy and meticulous, or did you give it all up for assisted living? Or, are you the maintenance guy at the assisted living place?

Great fix, thank you. Resoldered those connections and put on a new antenna and garage door works perfectly now!

Thank you that was informative

Thank you I have searched all over for this exact thing.

Thank you for excellent video. My Maytag washer was directly start agitating without filling water either at the beginning OR during rinse. I suspected it is timer, so used your video as guide to repair it and saw 2 pins got shorted inside, so separated them, filed and put it back. It is working fine now. You saved me $100+ just for part and repairmen asked $300 parts+labor for repair. It hardly took 30 min to do this repair myself using your video. Part that I repaired was W10111389.

Spatula? Plastic knife? Sure these work, but I've used a stiff 1.5" putty knife. Plus the putty knife is stiffer which makes it much easier to use. AND the wife isn't gonna complain you "ruined" her spatula! There is plenty of room to slip it under the control panel without risking scratching the washer, just make sure the putty knife is clean and rust free and you won't scratch any paint

Thanks for your help. I’m 25 and have my own lawn now. I’ve edged my dad’s lawn growing up but never had to reline it. Thanks for helping me further become a man

My door is closing and then coming right back up. Nothing to do with the sensors since I eliminated them when I had the unit installed a while back. My kids are grown and my dogs are never in the garage or near it.

Thanks a lot ! I was able to fix by looking at the video

Thank you so much for making this video. I needed this exactly since my washers lid switch broke and was not 100% sure how to replace. God bless.

Wow. Thanks Adam. Exactly what I needed to see. I have a spoon wrenched inbetween the grinder ring and the hopper wall. And now I know or guess that it is because that plate is wearing thin? I truly appreciate your video enough to subscribe.

I just bought the Craftsman 3400 psi washer and I knew right off not to do some of the things another video did, like not hook up the water first. Great video sir.

Thank you. Easy fix.

I used your video to troubleshoot my dryer and the thermal fuse was open. Got a couple replacements off Amazon and voila the dryer works! Thank you!

Excellent, you did it. Great job 😂

Spinning the wheel to give it momentum was the trick! Saved me the cost of a new and unneeded electrical controller!

I bought one the same model at a thrift store for $10... Bought a battery charger for $16 on Amazon haven't tried it out yet, thought something was wrong with it because it wouldn't go from a dead stop🙄🤔

thank you so much ..for the first time in my life i didnt have to call my husband to come fix the disposal 😅😅

Thank you for the awesome video. I got half way through then checked my new mirror and it was a different colour lol. It was wrapped up.

It's been almost a decade and u still saving people 100s of hours.

Great video, that fixed my leaking!

where's the flashing?!

Thanks Adam !!😊

Great video ! Simple and explained everything very well

I know this was possibly close to 10 years ago, but I want to say thank you very much for your assistance. I purchased this bookcase last week & I haven't been able to assemble due to physical reasons & today I was going to give it a whirl, but the military me knew there was a K.I.S.S. Method to the madness in the instructions. Your video has allowed me to take some necessary notes and also think of an idea. I was thinking of adding 2 long pieces of plywood in a criss-cross manner on the back for stability. Do you think that's doable?

They do go out and I heard, if bad they will stop the heating element from powering up.

Damn now they are $2,000!!!!

If they could make this ebike with 2.5 inch wide road tires, it would be perfect.

Thank you! Water heater shut off after a new gas appliance was installed.

I just bought some plastic toy pliers. It looks like something like this might be great application for my new tools