For details and pricing, visit our website at www.printdesigns.com/basics-curved-counter
@ElormBeenie2 күн бұрын
Thanks for this video. Just have me an easy way out😇🙏🏾
@moneisblessed94952 күн бұрын
The locking pin that came with my banner stand doesn’t fit inside the hole on the side! Now what do I do? 😖
@PrintdesignsLTDКүн бұрын
Hi, On your banner stand there will be an outer hole on the casing and a hole on the spindle inside the roller banner. When you put the pin through the outer hole, it has to line up with the hole on the inside for the pin to push into place. You will need to pull the banner up and down so the spindle inside the banner stand rotates and the two holes line up. Try pushing on the pin whilst you pull the banner up and down and you might find the pin locates correctly. If the pin you have is too big to go through the hole, you can use something smaller such as a small Allen/hex key, a nail or possibly even a cocktail stick. I hope this helps! Best wishes www.printdesigns.com
@PrintdesignsLTD6 күн бұрын
For more details and prices on Twist 2 Banner Stands, please visit our website at www.printdesigns.com/twist-2-banner-stands
@poseyparks369312 күн бұрын
My sign snapped from the top. I should be able reattach. Thank you so much.
@MasonObjora2 ай бұрын
I saw a monitor like this at McDonald's, you can order a hamburger through it, and what are you gonna do with it? ))
@PrintdesignsLTD2 ай бұрын
I guess that the type of monitor you are describing at McDonald's was a touch-screen device. The product shown here is not a touch screen (although we sell those too). Non-touch screens are typically used for in-store advertising but can also be used in other spaces to relay messaging to customers.
@PrintdesignsLTD2 ай бұрын
For information and prices, please visit www.printdesigns.com/basics-round-counter
@marcosfurukawa11042 ай бұрын
!1. Excelente vídeo! Muito bem explicado e informativo.
@abdelkebirtaghia36903 ай бұрын
شكرا جزيلا
@PrintdesignsLTD4 ай бұрын
The Vantage Banner Stand is available to buy online at our website www.printdesigns.com/vantage-roller-banner-stand
Hi, you should use a good quality permanent adhesive tape. We use 50mm tesa 4965. It works well for us based on the printing materials we apply to roller banner stands at www.printdesigns.com but you should test adhesion to the particular print material you are using to make sure it holds OK!
@MS-uz4ix Жыл бұрын
Accidentally pulled the pin and the spring on the roller unwound. Any tips on rewinding the roller to get back to the original tension?
@PrintdesignsLTD Жыл бұрын
Whoops! sorry to hear about this. The banner can be fixed but it's a fiddly process. The first thing you need to do it remove the screws from the end plate of the stand that has the flat spindle protruding from it. With the screws removed you can rotate the end plate of the stand clockwise while it is held flush to the casing of the stand. The flat head of the spindle should be still poking through the slot when you rotate the end plate. Be careful here because as you rotate the end plate with the spindle poking through the slot, the tension on the spring increases inside the stand. It is easy to accidentally pull the end plate away whereby the spindle will pop out of the slot and 'lose' all of the tension. Also be very careful that the end plate does not fly out of your hands whilst turning it or you could hurt yourself! We wear gloves and safety goggles when doing this. You need to give this end plate about 20-25 turns after which the print should be wound back into the stand. Once the print is wound in, put the screws back onto the end plate to secure it. Again, be careful that you don't pull the end plate away from the stand and allow the spindle to pop out of it's slot while doing this or you will need to start over! I hope this helps and good luck.
@MS-uz4ix Жыл бұрын
Thank you!
@dylanweinholt4978 Жыл бұрын
Keep up the awesome work! You should look into using a service such as "promo sm"!!!
That was simple and great information I needed!! Thank you! 👍
@NitinKumar-wo4qp2 жыл бұрын
Hello sir
@olyvia95962 жыл бұрын
You’re a lil intense
@tkbradford12472 жыл бұрын
Thank you. This was perfect information. I am above average handy, so I shouldn’t have any problems with this. I just wasn’t sure how it would attach on the bottom, and your video explained it in great detail.
@PrintdesignsLTD2 жыл бұрын
No problem, i'm glad the video was useful. You will need to use a strong double sided tape to attach the print. After sticking the print to the stand you can over-tape the join between the graphic and the stand with parcel tape. This will make the join more secure!