can this actually go into the sensor in side of dpf ? - or is it better to take off the dpf sensor tube & spray down that ?
@user-uc7ke4si1jКүн бұрын
🤕!
@SW-qr8qeКүн бұрын
My drum had lots of slop but the bearings were ok. The plastic bearing seats on the drum had worn larger than the bearing. Reckon it had spun, a lot.
@dspirto2 күн бұрын
Excuse me, do you know how to synchronize the control with the central box?
@Art_crafts_colours3 күн бұрын
Nice 👍 useful information 👍
@CWhite-rd6xh4 күн бұрын
That is not an "easy" fix. LOL
@FelipeSantos-bb4jm4 күн бұрын
It was a wasted of time...😵💫
@ArbitraryOnslaught6 күн бұрын
Might need new brush
@ZutiDIY6 күн бұрын
kzfaq.info/get/bejne/qbWYf6imqdSof58.htmlsi=IfvSCyZ2K2ZCvWHd Complete Video
@mosam50976 күн бұрын
Oh mate pls advise me::: should I run the car for 10 15min and the put this in… and drive again for 10 15min … or tell me the best way to get best result pls
@cleaneat_shealthyrecipes57018 күн бұрын
Thank you this was quite useful
@lakovlzr8 күн бұрын
Hello, is this the same way on the peugeot 407 2008? Thanks.
@ios758411 күн бұрын
Min.3:54 De ce ai tăiat plasticul ăla? Când montezi regulatorul pe alternator, acel plastic de protecție se montează jumătate, nu îl împingi de tot. În felul ăsta ține cărbunii comprimați. După ce ai montat releul, decât împingi la maximum acel plastic de protecție și cărbunii se eliberează, atingând colectorul.
@SharaNabadda13 күн бұрын
Can i use multimeter insterd of bulb
@ianwood724114 күн бұрын
What's with your test light,can you please explain how to make one.where are you getting the power supply from to the light
@technicaltreats270414 күн бұрын
This motor can be continuously used for how many minutes?
@BurtReynoldstash15 күн бұрын
Legend
@ItchyKneeSon15 күн бұрын
What grit sandpaper did you use to file down the commutator?
@ItchyKneeSon15 күн бұрын
I recommend getting 7 mil or 9 mil thickness nitrile gloves. I've used those thin 5 mil ones while working on rusty cars for 20 years and they tear so easily. I got a box of 9 mil and they're AWESOME!!! They last MUCH longer for about 2-3x the price of 5 mil.
Bonjours Pas mal mais quand c est abîmé à interieur aussi on fait comment ...merci
@ahhimary347525 күн бұрын
What is the diameter of the drill hole to use? is it same for canon pixma MX495? what ink colour used for hole in the left and top? the right is it yellow?
@jcr648328 күн бұрын
Not show wire connection
@aziz-sweden29 күн бұрын
This is a turbo, not EGR.
@darrenj8329 күн бұрын
Electric key in meter! Quick before it goes...
@jameshughes8937Ай бұрын
How did you pop it out so easy? These cars suck
@stoneislandkirkcaldyАй бұрын
I've literally just fixed my Citroen Berlingo 1.6HDi using the same approach but with Mannol DPF cleaner. I could not get the O2 sensor off with just the spanner so I ordered a 90mm 22mm long reach socket that has a gap cut into one side so that you can fit the O2 sensor wiring through in order to loosen the nut. I used a breaker bar on the socket as it was very tight. I did not even use the whole 500ml can. I let the car idle for a while then took it for an 18 mile drive up and down the motorway. The DPF warning light as well as the EML came on one more time to put the car in limp mode but I pulled over into the hard shoulder and cleared the fault code to take back out of limp mode and went back to the motorway driving. You can easily clear the error code causing limp mode with just a cheap code reader off Ebay. The port to connect your code reader can be found inside the glovebox or around the steering column if you are in Europe. I hope this is useful info as it really can be done and it's not complicated.
@Chonky_boiАй бұрын
I did the same thing with the virgin 360 box and got a free 1tb hdd.for my ps4 that had a failed hdd 500gb
@billwest4570Ай бұрын
Can't beat a nice salmonella strip!😂
@aminahmed887Ай бұрын
Agr capacitor na lagae to
@marcushall8432Ай бұрын
Waist of money
@user-od4dc6up6uАй бұрын
muje lena he
@user-od4dc6up6uАй бұрын
shop adras
@hannumonto209Ай бұрын
Use a torque wrench.
@maryanneparker863Ай бұрын
Thabks for something short and straightforward
@1289vinayАй бұрын
Good information
@jonathansimmonds5784Ай бұрын
What a useless video, try some commentary, and yes, do the fecking screws up again!
@josuecerqueira7191Ай бұрын
you didn't clean the EGR dude...if anything you dissolved crap and sent into the engine...it takes a LOT of work to clean the EGR valve + intake + pipes...and that you certainly didn't do...
@vitalylysenko4161Ай бұрын
👍 Good.. Thanks you.
@martinpokorny7599Ай бұрын
Peugeot 5008?
@ZutiDIY19 күн бұрын
Partner Teepee
@AndreDeSwardt-ur4jxАй бұрын
I tried Wynns Stop Smoke and before using it I warmed up the bottle and made sure my engine was warm before throwing it in. It worked brilliantly for my old car and no smoke came out of the tailpipe no more. Early detection also helped. Another thing is my car felt smoother on the road. What a fantastic product.
@user-oq6vj8xm6qАй бұрын
Its the only mount? Or there is more?
@ranbirsinghheer8174Ай бұрын
My dehumidifier collects water from air but fail to put in buckets please explain me
@adventureswithMustafaАй бұрын
Wow that's cool❤
@nityadevinatha4841Ай бұрын
Muchas gracias!
@xianreissАй бұрын
Is this video for real or are you trolling? If you caulk around your taillights you won't be able to remove the assembly. Wow I can't believe it.
@ZutiDIY19 күн бұрын
You don't need to remove the assembly to change the bulbs.