What part of the country do you live,because I live in Dallas Tx I wanted you to look at my 06 f350. Please

You are overthinking it. Just paint the letters.

I just use tripoli and rouge on a buffing wheel.

Cool the blue diamond is an overhead valve.

Paint the frame, sheesh!

I don't like the lining because it comes off. Personally I just fabricate another gas tank.

Its not an ignition control module, its the regulator.

You know tuners are not good for the engines unless it's light, custom to truck tuning. Next is contaminated fuel, diesel quality sucks. An aftermarket water seperator should be installed. Next is the pos air filters, AFTERMARKET AIR FILTERS DO NOT FILTER AS GOOD. 99.93% IS THE MINIMUM EFFICIENCY YOU WANT. THERE IS A HUGE DIFFERENCE BETWEEN 99.93 AND 99%. AND CHANGE YOUR OIL!!!!

Great video!

How did you get the front cross member out it rested on both sides in your video it was there and the next shot it’s not how does it come out without cutting it

Where did you find vin # please I have one similar

8.3 cta with a mechanical 653 trans is the absolute best. That bus also has the not so effective air to water intercooler that circulates hot coolant.

Where did you go? No videos in over a year. What happened to the Blue Bird Bus?

I didn't think you could use Zero Rust on sheet metal. Have you had any issues with cracking?

Use a semi deep socket and wedge something in behind the ratchet but don't be too rough and don't the oil pan

Did you have to drive the truck across the scales or did they check brake lights, etc. in CA?

I want 8.3 . I want ungoverned ; too many crackas on the road going slow .

My 6.0 just started making a lifter noise after 270k and suddenly began to overheat. I’m determined to fix it myself one day 🤔

Is this what you do for a living?

Bounces around just like the originals

Nice project, I put my 48 on a chevy 4x4 frame, Is there an easy way to pull the chrome strips on the grill ?

What model was this bus specifically? this is exactly the bus i'm looking for

Hi im trying to replace the seat in my 1965 gmc truck but all i can find is upholstery kits. Do you know where i can find a seat?

I connected that way but in third gear, 40 mph, my truck it starts shaking when i step on the gas pedal. What could be the problem?

What did you do with the orifice fitting for the wastegate?

Do you know where the VIN is located in a 1936 Ford Pickup? Thank you!

NICE DULLY 🪬

Love the travelall!

I am in mo i need someone who can work on my 60

What state are you in

Another very good option following the rear engine, good access and transmission. A little more of a “newer” model. The Thomas Saf-T-Liner HDX or MDX. BE PICKY! Get one that that is pre-emissions, and one that has pass through underbelly storage. Maximized living pace and getting the best bang for your buck! Those have a couple engine options. The newest ones have the Cummins engines, BUT, they have emissions systems. The older ones have CAT C7’s and the Mercedes. I recommend the C7.

Good vid. One thing though, the pump was probably good. If the pump did wipe there would be metal in all of those injectors and they would of plugged up quickly. It was probably a lifter, the metal would fall into the engine and ve pulled into the filter housing, it would also likely wipe the lpop and cover. What did all that look like on the motor with the cast iron. Pump?

Heisenberg lookin mafk

What happens if the 2 wires connected ground out? Does it damage anything?

I'd love that bus if it was half as big. I have a 24.8 ft long conventional. International with the dt444e. Wish it had the 8.3 Cummins ...no such thing. I don't know how many people I've seen that become disenchanted pretty quickly with that big of a bus... They can sure enough be a money pit.

That's good information sir , information is king on making good progress and development in choosing a platform to. Build on

Hi . Where is the VIN plate located on your van? We have the same van and are trying to locate the vin plate. Great project!!

TV cable not a kick down cable

Keep it. It might be worth a lot in the future 😮.

Got a 05 with 180k might just change the injectors now honestly haha

Good job very nice truck can’t wait to see when it’s done!!

Any chance you can tell me the height of the inside?

Dodge Cummins and Ford Diesels.....Run!

great job but not for the novice

We need a update!

Smart 🤓 guy good information thanks 👍😊

How did the hill choice in an almost stock Land Cruiser fj45

I got this same bus.you are right they bad to the bone .its still a scool bus im.converting it next month i gave $4500 For it and dont regreat it at all .i bought it from AAAbus in phoenix and they got a stock piles of used parts and busse. Not to mention they treat ya family when you'er there. No bullshit sales man .they wont sell you junk .

How do I find the next video?

is this snake oil or is it legit. what are the benefits