Part V518 will not fit in the hole in my valve cover it is different then the original one that was in it. not sure what it the problem 😢

Saturn doesn't have that valve or at least is not the same as the Acadia, the autoparts store tells me that 2007 saturn doesn't have PCV valve.

Thank you for your knowledge and expertise

Very good explanation thank you.

What is the part number???

do you think the cooler fills up all the way or any thoughts it might have air pockets being that the lines are upside down? i know the factory one was upside down aswell but was also smaller

Protip here. If your going to cut your lines and most of us can not make a barb style connection on OEM cut line. Use a flaring tool and slightly flare OEM cut line. Make sure OEM line is very clean on outside since you are sliding hose over it now. The hose will go over the line and use 2 hose clamps to secure for every connection. It makes for a guarantee leak free connection

Dorman part number 800-605 for those not wanting to cut the trans lines.

Came for the part number thanks bro! 😎

At 2:35 you have broken the guide, the wrong way

Try using a buffing pad on a drill method. Takes about one hour total. First, Cover painted surfaces with painters tape. Second, Coat headlight with light coat of the Flitz polish, wait about 5 minutes to allow the Flitz polish to draw out oxidation from the plastic, and Third Buff off polish with a drill buffing pad. Repeat the same procedure at least one more time for increased clarity and shine. This method works well to restore clear hard plastic such as automotive headlights.

If your car stalling or die after start, disconnect the iac and just drive home first.

THIS is even better than the Santa Fe spark-plug video!

Thanks dude. This is an excellent resource. Much appreciated.

Well done. Had the same problem on my 2008 GMC Acadia, but I didn't know there were 2 PVC valves until I watched your video. Will be changing them soon! Appreciate the sharing!

Dont mod these parts. You are not smarter than the GM engineers

Did this stop the vehicle from smoking and or burning oil?

Who told you what the drill dimensions actually are?

Nice great information Man... If you need worker am available for Auto electriction now I do work in Saudi arabia

Soo sad just how much that PVC valve affected the motor. A low cost part ignored by many people.

Worst engine gm ever built. Should have never got rid of the inline atlas engines.

This is a $15.00 part.

GMC Terrain 2012. This worked perfect when I replaced on my wife's car. Couple of pointers for this make and model car. Seems GMC tried to be slick by placing the purge valve in a tricky spot so you have to go to the dealer and pay them 3-400$ to get it done. I was able to accomplish the job and here's how. 1st remove the engine cover by taking off the oil cap and remove the bolt that holds the cover down (rt next to oil cap area). Firmly grip the cover and pull it up. It is snuggly attached to 3 rods underneath but a firm tug should free it up. The purge valve is on the passenger side of the engine in the back. You will need to use a flat head screwdriver to loosen and remove the air intake tube (not a mechanic but I believe that is what it is). It's the big black tube thingy with ratchet brackets holding it tight on both ends. Remove it, it will be in your way if not. There is then an electric box maybe 2inch by 2inch (with wires coming out of both sides) attached to the side of the car frame. Pull this loose (it is attached to the side of the car frame by some blk plugs) push the box down and out of the way. There may be some other wires and things you want to move to the side. Otherwise you will not be able to access the bolt on the purge valve or be able to disconnect the plugs attached to it. When you have your way clear just follow the directions on this video by removing the plugs, loosening the bolt and pulling the purge valve out. Reverse the procedure to install the new valve and you're all set. Worked like a charm and save me a lot of money. Bought the valve for $50 (California) and the whole process took me about an hour which most of the time was spent figuring out where GMC hid the valve in the first place. Hopefully this saves you some time since you'll know where it is and how to access it. Cheers to the maker of the video!

How do you know which line goes to what hook up ? How much trans fluid did you have to replace? How much did it lower trans temp ?

Mine won’t come out , how do you get it out ! I’ve tried every tool to pull it out and it doesn’t come out

I have an 09 Buick enclave , I can’t get the back PCV out !!

Nice install looks good. Inspires me to do mine as well. What is the vertical cooler to the right? Looks like you replaced that one as well?

Now that it’s been a year. How has the install worked out for you? Like the video above most others I’ve seen.

Does 2012 Impala LT have the updated version? Thanks!

Excellent

So by having this problem does it make your rpms idle up and down?

great job thx

Been trying to solve this problem for over a year.... cleaned and reconnected the pcv valve and no traction control/stabilitrac error in 70 miles! Thank you!

same my bad IAC thanks for youtube smile ...

Thanks!

Thanks! Does it read the temperature well? Does it turn off when it hits the set temperature? The stock one we have doesn’t turn off on its own. I’m hoping this will fix the issue.

This is a vent not a valve. Keep your oil clean and change your filter regularly from new and you won't have the problem!

Hope this works on my 2008 GMC Acadia. Just did the mod. Question - I removed the old PCV with some difficulty, when I replaced it, it just slid right in up to the stop. Tried pushing further but wouldn't go. Is that ok?

Gread vid, thanks for sharing! 👍

IT;S PCV !!!!!!!!!!!!!!!!!!!!!!!!!!

Did you have to add any fluid?

PVC (:46 and 1:06 in the video) is polyvinyl chloride, a type of plastic. The valve you replaced is the PCV, positive crankcase ventilation.

If you take it off and start your engine it will push the pin out it self to clean it

Thank you so much guy. This P0720 has been dogging me but now I'm good - huge thanks

From what years are these part compatible with? Ive been searching for 2017 enclave and the rear orifise dont show nothing for that year

This doesn't fix anything, it will let more oil into the intake manifold, intake runners and intake valves, add an oil catch can to help with this issue

Nice. I have the new hose and was a little curious about the disassembly of the grill assembly. Thank you very much, will do today. Looks easy enough.

I had the lightning bolt warning and had this fixed recently, maybe 3 months ago? Well the light is back on... any idea why something like that would go bad so quick? Maybe its a faulty part or something, but generally speaking, could something else be wrong thats messing the ETC up? Man im so annoyed, two things I just had fixed need to be fixed again...

Did the temp drop from 190s? Eldian has a very good question as well! 😊