How do the rinse nozzles cut the flow of bleach? I had no idea you could do that, I always had just taken the line out of my bleach bucket every time
@dougrucker67838 сағат бұрын
The soap nozzles lower the PSI of the machine so the bleach draws, when you put the rinse nozzles in the PSI is raised back up so the bleach can not draw. Just like using the black nozzle that comes with a machine, versus the colored higher pressure nozzles.
@danielfisher1283Күн бұрын
What's the swivel measurements? Need a new one
@ktpowerwashing3 күн бұрын
Doug Ruckers Pressure Washing School is 2nd to None! Doug is a true industry veteran. Wish you much continued success Doug!
@dougrucker67832 күн бұрын
Thank you and back atcha
@shaferspressurewashing89113 күн бұрын
Doug is a businessman, but much more than that. He is a people person. He has ALWAYS taken time to answer all of my questions when I have them. By the way... He builds some great rigs also. Check him out online!
@dougrucker67832 күн бұрын
Thanks Mark. Appreciate you
@go2powerwashatl4 күн бұрын
🔥🔥🔥🔥🔥🔥
@countchungalitus76045 күн бұрын
Why provide bleach tanks that violate DOT? Can't you get a MASSIVE fine if you don't have UN rates tanks?
@ScottTerry-yc4uu5 күн бұрын
How much is the online school ?
@vcash11126 күн бұрын
⭐⭐⭐⭐⭐
@JacobG.058 күн бұрын
I got a Simpson machine and the pressure outlet is a qc socket kit with a male m18 can I change it to a qc male plug or do I have to keep that oem kit?
@dougrucker67837 күн бұрын
Yes there are conversion fittings available, we just don't carry them. Might contact Simpson and see what they have available.
@JacobG.056 күн бұрын
@@dougrucker6783 okay thank you
@RichardCInman8 күн бұрын
Do you cram a 12 minute video into 48 minutes?
@PressureCleaningSch8 күн бұрын
@@RichardCInman I would never do that.
@richardnichols20649 күн бұрын
what is the psi rating of the ball valve? the seals will blowout if not matched to equipment. also if your using a valve you better have a unloader moving the water pressure somewhere else or risk overheating your pump.
@PressureCleaningSch9 күн бұрын
@@richardnichols2064 these are for dedicated pumps. Not pressure washers.
@kmc66910 күн бұрын
Will a M5 nozzle 3-7 gpm work on a 2.5 gpm pressure washer?
@dougrucker678310 күн бұрын
I doubt it will work very well for distance since the GPM of your machine is so low.
@kmc66910 күн бұрын
@@dougrucker6783 thank you
@shaileshbhagat527510 күн бұрын
How much price of pressure machine with all nozzle
@PressureCleaningSch10 күн бұрын
All the prices are right here at this link. www.dougruckerstore.com/collections/pressure-washers
@alejandrocortezpalacios328710 күн бұрын
What is the recommended psi for operation?
@PressureCleaningSch10 күн бұрын
4 GPM minimum. 2500 PSI Minimum
@alejandrocortezpalacios328713 сағат бұрын
@@PressureCleaningSch thanks
@kevinjones199310 күн бұрын
What kind of drop stick you you have in the Sh tank for the king slinger
@PressureCleaningSch10 күн бұрын
I don't use a drop stick. I use the clear braid hose to the bottom of tank and weight it down with PVC
@kevinjones199310 күн бұрын
@@PressureCleaningSch do you sale them at your store
@PressureCleaningSch10 күн бұрын
@@kevinjones1993 the clear braid hose yes. PVC pipe we do not.
@HouseWashingRick11 күн бұрын
Hello Mr Doug
@dougrucker678311 күн бұрын
Hey Mr. Rick
@pjaydomingo662912 күн бұрын
Does the actual swivel have o-ring inside on it?
@dougrucker678312 күн бұрын
Yes it does
@deanrucker13 күн бұрын
2024 updates!!!
@deanrucker13 күн бұрын
Edwin is the man!
@deanrucker13 күн бұрын
Good stuff!
@deanrucker13 күн бұрын
This stuff works great on pretty much EVERYTHING!!!
@deanrucker13 күн бұрын
Always helping the folks!
@MarianneMorris-e5s17 күн бұрын
What solution doe you use on tennis courts? How long do you leave it on?
@mahdi318118 күн бұрын
Doug My prusher washer is 2500 psi 2.9 gpm with 100 ft hose 1/4".. do you think that i would upgrade to 3/8 hose???
@dougrucker678318 күн бұрын
No with that low a gpm you need to stay with the hose that came with the machine
@makycaris467219 күн бұрын
Nice 👍
@kylebaker822419 күн бұрын
Doug- just to clarify: if an injector has a 20% rate and I’m using 10% SH, I’d be getting about a 2% mix coming out of the gun?
@patriciasierra577819 күн бұрын
Im so glad you all are safe!!
@kylebaker822420 күн бұрын
Doug- I run a fence/deck staining business. I use a small, portable 2.6 gpm pressure washer with an AR pump for prepping the wood. What do you think would be the easiest method to apply a 2-3% SH solution? I’ve tried using an X-jet but it’s not easy to use when doing two sides of a fence. Thanks!
@PressureCleaningSch20 күн бұрын
Hey Kyle, either using a pump up sprayer or using a dedicated 12V Pump. If you can use the pressure washer that may also get you close to 2% or at least strong enough to change the color of the algae on the fence.
@kylebaker822420 күн бұрын
Thanks Doug! The pump up sprayer is a little inefficient when doing a big fence and I don’t have the ability to get a 12v system just yet. Using what I have…..
@kylebaker822420 күн бұрын
Does using a down stream injector cut the SH percentage in half like using an Xjet with no proportioner?
@ExpertPowerWash21 күн бұрын
Glad you guys are ok!
@dougrucker678320 күн бұрын
Thanks Tim
@ridethepace600521 күн бұрын
I'm glad I was able to purchase my machine from you, and when I can finally add a 10 gpm skid, you will be getting that call. No question.
@ktpowerwashing21 күн бұрын
81 yr old mother was standing in her hallway when a 60 ft Cottonwood Tree crashed down onto / into her 1 story home. The base of the rootball was 34' diameter that uprooted. She got out without a scratch but house is totaled, every room. Thank God she was standing where she was when it happened.
@dougrucker678320 күн бұрын
Yes Praise God she's ok. Wow that was close
@gcsoftwashllc21 күн бұрын
Glad you guys are all Ok. 👍🙏
@dougrucker678320 күн бұрын
Thanks so much.
@smitty469921 күн бұрын
any reason why you use the 25 and not the 15 degrees?
@dougrucker678320 күн бұрын
Have used before on a 3 nozzle bar, but I just prefer the 25. We have never gotten a request for a 15 that I can remember.
@Jay-Kaizo22 күн бұрын
What do you do if your test on the concrete shows that you will leave etching? Do you go with very low pressure after an sh mix?
@dougrucker678320 күн бұрын
Yes. Just a light wand rinse after pre treating
@Jay-Kaizo19 күн бұрын
@@dougrucker6783 Thanks so much, Doug! Love your channel and I just realized I'm not subbed. I'll fix that :)
@dougrucker678318 күн бұрын
@@Jay-Kaizo Thanks Jay
@user-ok8is7mk4w22 күн бұрын
Hey Doug, previous student here,,, my question is can you leave the flowpro connected at the pump of the pressure washer and run it in bypass for surface cleaning ect....
@PressureCleaningSch22 күн бұрын
@@user-ok8is7mk4w yes mine always connected. Surface clean when in rinse mode for full flow and pressure
@lupedominguez916322 күн бұрын
Why isnt the thermal relief valve opening. I replaced it bc it was not closing. It kept spewing water. I replaced it with two new ones and now it does not open at all. Can you help. Please
@lupedominguez916322 күн бұрын
Both new ones didn't open.
@dougrucker678320 күн бұрын
They only open and let water out if the pump overheats.
@trcknup23 күн бұрын
I see a lot of guys say they dont use proportioners with the xjet. My question is, whats the technical difference between an xjet and a downstream injector. Like internally what is different? Im wondering why you cant just put a downstream injector at the end of your gun and use an adjustable tip to get close to the same results at less than a quarter of the cost of the xjet.
@dougrucker678320 күн бұрын
You can do that but it will not be the same results as x Jet as far as strength. Difference is X-Jet does not operate off a venturi like an injector does. Injector requires pressure difference to draw the chemical. X jet uses the high pressure at the wand
@aaronbailey364023 күн бұрын
Thank you for showing us how to turn off the mix. No one breaks it down as simple as you do. I appreciate you.
@PressureCleaningSch23 күн бұрын
@@aaronbailey3640 very welcome and thank you.
@FilthyForce24 күн бұрын
Thank you!
@PressureCleaningSch23 күн бұрын
@@FilthyForce very welcome
@shaferspressurewashing891124 күн бұрын
Doug, I'm glad to hear that you and your family are ok. God bless you and your family.
@patriciasierra577824 күн бұрын
Hello Sir! Nice 2 meet you. Thank you for letting us know they are well.
@calvinjohnson817625 күн бұрын
God bless you guys
@aaronbailey364025 күн бұрын
Absolutely love this start up pressure wash machine. Thank you for helping us beginners.
@PressureCleaningSch25 күн бұрын
Happy to help!
@muahaha592925 күн бұрын
Thanks for all the great tips.
@PressureCleaningSch25 күн бұрын
Very welcome
@ridethepace600525 күн бұрын
Great explanation.Thanks. I can't wait for my new 8 gpm machine to arrive. Thanks for the quick turnaround time. ( The guy in MA ).
@PressureCleaningSch25 күн бұрын
@@ridethepace6005 should be picking it up today. We got delayed for to the hurricane but it’s ready to go.
@ridethepace600525 күн бұрын
I assumed that might be the case. I hope you all fared ok.
@deanrucker25 күн бұрын
Love it!
@rgvleo527025 күн бұрын
The business can wait. You need to take care of your family first. Prayers for you, Doug, and the entire Rucker family are on the way!!