Use a red butt connector crimp a piece of copper wire or small screw in it. Drop of super glue on the other end slide it on and you’re good to go.

Good video, thx. 👍

Nice presentation! I wonder if sanded aluminum (powder) could be added to the baking soda?

Should be titled “how to be all over the place and almost drive through the garage driveway plowing”

W😊W GREAT TIP 👍🏻

Nice

just rinse with distilled water. If rinsing would work, and that is hit or miss, then that would do it, then put the right mix of acid and distilled water back into it. It's hit & miss since you can't see between the anodes and cathodes to see just how bad it is.

So why does my spring always pop off

I run O'Reilly 5W-30 convention oil in my 09 Tacoma, my truck run smooth just like the oil change from Toyota dealership . Good oil I will keep using O'Reilly oil.

You’re right helped me start my car

Thank you for being understandable and to the point.

Thank you for your video, very helpful. Literally the problem I'm having. 👍💙

Thank life saver !!!

I'd be interested to see cotton impregnated with baking soda. I think the fibrous nature of the cotton would aid the baking soda in tinsel strength....

Got me up and running in 2 minutes. Thank you !

Thanks for trying, and showing us your result!

take a shot everytime he says snug

Can you do this to a tea pitcher? Will heat from the tea leech the chemicals to the tea?

Thank you so much!!!

I just cleaned this same carburator. I have three inlet places . One for the gas and one for the primer. The small inlet I don't know what it was for. Maybe it was for air to the carb. I just don't know.

What do you do when you can’t see well enough to fix?

You could evevn use the right diameter of the old telescopic antena fir adjusting the carburetor 's screws. Thanks

good Job Love the song

On a murray 2500

Who sells the proper screwdriver tool?

You can't find the screw adjustment screws on my carb... I'm going in.

Thank you so very much Bob for all the insight on topics you just cannot find answers for anywhere else. I hope everything is going well for you! Take Care & God Bless!

greatest video ever thank you

Thx, got a GM so even better I found you with yours. Had a good idea it was the starter but didn't know where to find it. Now I do, thx

Thank you, I had the same exact issue with the same exact machine, what are the odds? Thank you again.

Thank you Vice Grips Bob. I'm about to use this recipe on an alumitub submerged aluminum firebox.

Can't you just take the Positive off and leave it off for an our to do the same thing?

They're trying to make it a hard as possible to do any home repairs. I'll give your suggestion a try until I get my adjustment tool in the mail. Thanks.

Thank you. Just put a new carb on the wife's weed eater and was needing to pull the plug and add a drop to start it. This should make it all better.

Why not clean the bearing with gasoline then pack them? Why do you mix the old grease which came out back into the new ? :)

My 32cc professional 4 cycle craftsman weedeater doesn't have those screws.

You saved my MUTHAH FN DAY !!!!!❤

You are, the man worked like a charm

Would love an update.

Thanks! Really Helpful.

I repaired my rad on my Dodge Ram with crazy glue and cow brand and it was awesome how good it worked and lasted

gracias hermano un abrazo desde Venezuela

great explanation.

Thanks great video

You can take a plastic ball point pen take out the ink and the end plastic fits on the screws

I am a woman and nobody can help me. Looks like I have this problem and want to fix it by myself. What kind of starter I have to buy? Or they are all the same? And where? On Amazon?

Not 1 time does anyone say to screw in or to screw out , nor do anyone say how many turns.

Wonder if that would work on the GM A/C condenser coil ? They always break at the weld.

Old school is better than that new school

Thank you because I ain’t byeing the same thing I saw the video the chain saw I’m got some of those that I can use I hate the unnecessary crap they put on these weird years and lawnmowers and everything is basically new. They want you to spend money every time when I work on the damn thing by myself to make it nearly impossible you have to take it to the shop. school is better than the school. Thank you for the tip.