What calculations did you make while designing and where did you make use of?
@kv1703 ай бұрын
Why was the flow zero at nodes 2 and 3?
@vishalbasutkar93693 ай бұрын
nice video sir thank you
@kunalpadalkar5984 ай бұрын
Nice
@kunalpadalkar5984 ай бұрын
Good
@kunalpadalkar5984 ай бұрын
Nice
@kunalpadalkar5984 ай бұрын
Nice
@Beginner2Creator4 ай бұрын
Can i use those rules and assume that the right angle (90 degree )
@johnsonvarghesenellisery14084 ай бұрын
According to slide number 21, (Inclination of conveyor with ground) < (angle of repose for the given material) So it cannot be used for 90 degree inclination
@Beginner2Creator3 ай бұрын
I appreciate it , is there any design procedure for Z-bucket elevator? @@johnsonvarghesenellisery1408
@Beginner2Creator3 ай бұрын
Please make a video of bucket elevator Z 90degree inclination
@sachristonemms28675 ай бұрын
hi there nice explanation Mr johnson, a question though should we not change the speed that was given on the table psg 9.20? and calculate the new speed base on the capacity ? Bim 800mm and Q=250TPH speed 1.52m/s Regards
@johnsonvarghesenellisery14084 ай бұрын
Hi, the belt width (Bmin) is calculated based on capacity Q=250TPH. And speed is calculate d based on final belt width (Bmin = 800) also standard on PSG 9.20. check slide 27.1
@sachristonemms28674 ай бұрын
@@johnsonvarghesenellisery1408 thank you Johnson will do, keep up the good work 💪
@saima.naz282 ай бұрын
@@johnsonvarghesenellisery1408 what is PSG? can you please share link thank you
@user-gg4xo5nw4d6 ай бұрын
nice
@user-gg4xo5nw4d6 ай бұрын
nice
@jeanmarychinnu20766 ай бұрын
👍
@alphonsaalphonsa90436 ай бұрын
It is very helpful for me
@alphonsaalphonsa90436 ай бұрын
Very easy to understand
@alphonsaalphonsa90436 ай бұрын
Wonderful explanation
@er.junedahamad38086 ай бұрын
Nice
@jeanmarychinnu20766 ай бұрын
👍
@vishalbasutkar93696 ай бұрын
Thank you sir for such amazing videos
@rehanmuqri2726 ай бұрын
Thank you so much sir for this video really Helpful
@user-gg4xo5nw4d6 ай бұрын
nice
@pkul19856 ай бұрын
👍
@er.junedahamad38086 ай бұрын
Short and sweet...
@sujitsahu47466 ай бұрын
Excellent Examples👍
@jeanmarychinnu20766 ай бұрын
👍
@13_b_dhirajpandit806 ай бұрын
😎😎
@rishiswatchin6 ай бұрын
👌👌👌
@sarthaksurve12876 ай бұрын
Well explained 👍
@family001kerala6 ай бұрын
Images conveyed more than Word Explanation great move 👍
Quiero fabricar uno de potencia de compresión de 20 toneladas , un motor de cuantos HP necesito?
@syedhassanali93307 ай бұрын
Thank you very much sir, very informative video
@arianagomez30588 ай бұрын
Hey...
@ceciliaelaine51138 ай бұрын
Hello, well done with this press, is it possible to share the design parameters for the components please
@musabshaikh57689 ай бұрын
Thank you sir
@Wowow1000010 ай бұрын
good explanation sir.by the way i have one question about rope drum groove design what standard should be follow as i have case groove start to go sharp so i need to know the rejection limit . thanks
@johnsonvarghesenellisery140810 ай бұрын
There are two types of grooves, 1. Standard groove and 2. Deep groove Standard groove is generally preferred.
@santoshddalvi11 ай бұрын
Excellent
@vipeshsingh3311 Жыл бұрын
Nos of falls at 1:12:30
@kunalpadalkar598 Жыл бұрын
Nice
@kunalpadalkar598 Жыл бұрын
Nice …
@aniketpawar3388 Жыл бұрын
short and sweet
@saeedsheikh4317 Жыл бұрын
SaEed
@mayagamaleldin9778 Жыл бұрын
can i use those rules and assume that the angle of incline is 0
@johnsonvarghesenellisery1408 Жыл бұрын
yes
@mayagamaleldin9778 Жыл бұрын
@@johnsonvarghesenellisery1408 i want to design a horizontal conveyor without idler just 2 pulleys and one driven by motor can i use those rules and the databook that u used
@johnsonvarghesenellisery1408 Жыл бұрын
Yes, ,but if the idler is not used, then distance between the pulleys cannot be more than 1.5 meters.
@mayagamaleldin9778 Жыл бұрын
@@johnsonvarghesenellisery1408 how can i get the resistance to motion value wu and wo when i need f and f is the friction between belt and idler and i am not going to design idler
@mayagamaleldin9778 Жыл бұрын
@@johnsonvarghesenellisery1408 but how can i get wo and wu when i am not using idler like what will be the value of f(the friction force between idler and belt)
@jonkelo118 Жыл бұрын
Di
@jonkelo118 Жыл бұрын
Berapa harga
@user-sm9hh9hz8j2 жыл бұрын
أحسنت ؛ إستمر . Welldone ; go ahead .
@dilipgahukar39022 жыл бұрын
3 tan ka chahiye co se compani ka oder kare bataye
@dilipgahukar39022 жыл бұрын
Hi...
@kentlouieeyana71892 жыл бұрын
Sir do you have a tutorial regarding power transmission from belt drive systems to chain drive systems?