A foundation moisture barrier should have been put down first. There is a foam type for wet area that might work after the fact.

This is cool video its interesting because I want a steel home some day and have hold ups about costs its emotional and gotta stay strong.

Your slab should be same height or higher than your exterior sidewalk

simple video. thanks. I don't see the proof that it worked though? The key-way for this part is right shifted compared to mine....

How’s it holding up?

Raid looks like it makes the insects think they're coming to a rave party. 😂😂😂

So that fixed the issue I thought it was the shift solenoid that caused that problem

my car had 3 transmissions in it at 100k i think ecus bad

Question prior to you replacing with the kit was the D and R blinking on and off inside the Cabin on the electronic dash? Mine does and feels like it in limp mode but shifts and reverses I don’t think it’s going past first gear but the letters blink and blink and sometimes it will stop blinking and pretend to act normal 🤦🏻‍♂️ Suggestions anyone? Mines a 2010

My friend has one..great car , smooth ride and very reliable..hidden gem..

Great video!

Did you have problems with the car acting like it is in neutral when you put it in drive?

Thank you sir for your video. I was able to fix my mother in law’s truck and get her back on the road safely 🙌🏾

it's an erector set.

For laying the freezer on the side you need to lay it on the right side. There is a video on KZfaq that shows you what side to set it on so you literally only have to wait 10 minutes before plugging it in.

WT5500

How do you program a WT five 500 wireless keypad to a 1864 power series panel?

Should've done a drip edge

Did you get any error codes or warning messages because of changing the type of bulb to the LED? Or did everything work just fine with no error messages?

I have a sway bar link mounted to a Hole in a Lower Control Arm on a Acura TL. I want make the hole slightly larger to accomodate the new larger swaybar link bolt. The LCA metal is probably 3/8" thick?. I am guessing it is cast steel. Will these bits work? The hole needs to be enlarged about 2 mm. thanks this is what it looks like. you have to stop the video and look at the Bottom end of that stabilizer Link. That is wher it attached to the LCA kzfaq.info/get/bejne/eM6dmZCZppm5qac.html

😎👍

How long does it take to get a full charge.

I bought one and it works great! But it cost $300 on Amazon.

🛠 ✨ ✨ ✨

Complete waste of money mine never worked right Straight Out of the Box brand new

The button the red button how should it be

Junk ...apple cider vinegar and dish soap will do the same

Thank you buddy

put your earth clamp where it does not get in the way and wet rag around the swivel eye.

Great video!

Use shampoo to remove gas smell from.your hands

So let me get this straight… you filled up your entire tank with injector cleaner? And what type of cleaner did you use? I’m having some issues with my 2011 Honda Accord.

Installed my new carb and still no start :/ just cranks. I have compression and spark too

Did you put brake grease on the pad surface that touches the rotor? Sure looked like it. We both know it goes on back of the pads not part that creates friction on rotor.

Thank you for this video. I have a 2014 Cadillac SRX that is downshifting hard into first. I thought that it might be a full replacement of yhe transmission, but because of your video, I've come to believe that the problem is in the solenoid vacuum plastic thingies you replaced in yours. I haven't takin it apart yet, waiting on those parts from Amazon to arrive. I'll tear into it this weekend to be sure. I'm almost 100% sure its those pieces you replaced. And watching your video shows me the right way to do it. Again, thank you so much from one Cadillac owner to another. Ill post an update when done.

OK, so I just bought this carburetor that you have on here, and I’m planning to put it on my homemade engine, instead of having it vacuum fed, can I have gravity, fed by the fuel tank above the carburetor? Thank you!

No check engine light cuz you disconnected the battery, my experience was the shift solenoid right in front on the transmission

Great video!

I purchased 2 and assembled them today, as a woman, by myself. It took maybe 15 minutes each. It recommends 2 people to attach the Lid. It doesn’t require 2. I’m very pleased.

HELLO, great video! Nice dutiful helper. What size socket did you use?

I bet you the sound better without the plastic on the back more air movement 🔈🔉🔊

I don't have 2 channels. I only have 1.

nice video, clear and simple. btw, do you need to reset or reprogram the srx after replacing with a new battery?

Was this the non bose speaker model?

Great video!

I love these lights!! We have one!!

Did you end up having to have it reprogrammed or was all good after using the repair kit?

Did u change any solenoids b4 jumping to the computers?

Why didn’t you use it with the trim on?

what size speaker would you suggest