Mahmoud Abido

Пікірлер

@pranchalengsaengma7647 23 сағат бұрын

Thank you so much sir

@MahmoudAbido 23 сағат бұрын

@@pranchalengsaengma7647 you are very welcome

@hype_henry 6 күн бұрын

Thanks man. Great information great videography and being very specific on recharging the ac. Appreciate you a ton

@MahmoudAbido 6 күн бұрын

You are very welcome, I am glad that you find it helpful

@livewithseatibiza6l245 11 күн бұрын

Спасибо за видео, я думал что замена будет похожа на замену платформы Ford Focus 2/3, та радиатор меняется через снятие бампера и переднего усилителя что удобнее и быстрее, но Mazda так не думает)))

@MahmoudAbido 11 күн бұрын

Hi, thanks for your comment. Unfortunately I can't understand what you wrote, can you please translate it? Thanks

@Devo1987 13 күн бұрын

So what does the expansion valve screw do do you know ?

@skworpiondevo9093 15 күн бұрын

Best video by far. Awesome work. Thank you for such great detail.

@Januareza13 2 ай бұрын

Bro, 2.0 cc or 1.6 cc?

@MahmoudAbido 2 ай бұрын

2.0 cc

@Januareza13 2 ай бұрын

@@MahmoudAbido thanks u

@MahmoudAbido 2 ай бұрын

@@Januareza13 you are welcome

@brenson77 3 ай бұрын

Great video man thanks

@teia9845 3 ай бұрын

since you had to replace the compressor, expansion valve, and condenser due to a seized compressor, how much pag46 oil did you have to add to the system since everything was replaced? I'm working on my mazda 3 as well, but my compressor came out bone dry without any pag46 oil so I'm not sure exactly how much I should add for the whole system since I'm also replacing the 3 main parts. Looking at the service manual, it mentions "A/C compressor oil sealed volume approx. 120ml" and "Condenser Supplemental oil amount approx. 35ml", so I'm assuming I'll need to add about 155ml of oil into my A/C compressor before installing, and is it okay to add all of the oil into the compressor only (since it'll move it throughout the system)? Additionally, since you flushed the HI pressure a/c line that goes from the compressor into the condenser, I assume there needs to be a few extra ml of oil added into the system (maybe 2-5ml)? Let me know if I'm on the right track!

@Devo1987 13 күн бұрын

Did you figure it out? How's your ac at idle or stop and go traffic ? How cold are you getting out the vent ?

@teia9845 13 күн бұрын

@@Devo1987 hey! i was actually able to finish the job and it works great now, been a few months so far with ice cold working a/c. I can't remember the exact amount of pag46 oil I added, but I believe it was 145ml after adding up all the necessary amount for each part in the service manual (not the owners manual), I'd recommend that you double check that by looking into the service manual yourself too. I replaced the expansion valve, condenser, compressor, and cleaned out the line that moves from the compressor into the condenser.

@teia9845 3 ай бұрын

im glad this video exists, theres basically no older mazda 3 videos to reference off of, especially when it comes to the AC system (my AC compressor was also seized up so it was contaminated). This is extremely thorough and well explained and even has an entire series covering everything!

@MahmoudAbido 3 ай бұрын

Thanks so much, I am glad that you found it helpful

@user-xq4jd3jp5f 5 ай бұрын

The best Video id say . . even someone who has never done it before can do it without having any doubts. Thankyou Mahmoud.

@MahmoudAbido 5 ай бұрын

Thanks so much My pleasure

@bisfal 7 ай бұрын

very good video.thank you very much.

@MahmoudAbido 7 ай бұрын

Thanks, my pleasure

@filip9171 8 ай бұрын

How much torque should the tensioner bolts be tightened to?

@MahmoudAbido 7 ай бұрын

This is a good question Thanks for asking The factory repair manual torque specification is 14-18 ft-lbs

@_dondie_ 9 ай бұрын

Nice vid, keep it up 👏

@MPAPILOS 10 ай бұрын

The most clear video i ever seen until now. Thank you man for sharing!!!

@MahmoudAbido 10 ай бұрын

Thanks, it is my pleasure

@mtnsports 10 ай бұрын

I was expecting to see you clean the tube between the condenser and the expansion valve....didn't you flush that? Admittedly that would be a challenge, but I thought you mentioned at the end of part 2 that you were planning to flush that tube also.

@MahmoudAbido 10 ай бұрын

Thanks for your comment, You are right, I was planning to clean the pipe coming from the condenser going to the expansion valve. As you mentioned, it will be very challenging, especially you have to clean it in the opposite direction of the refregirant flow (from the expansion valve to the condenser). We don't have enough space to do this. If we think about it, we will find that we don't need to clean this pipe. Why? Because we are cleaning the pipes to remove any contamination. The refrigerant flow goes through the condenser before reaching to this pipe. The condenser has very, very small channels, so most probably, any contamination will stuck in the condenser. Thus, this pipe should be nice and clean. Do you agree with me?

@albertma413 10 ай бұрын

I love your video.

@MahmoudAbido 10 ай бұрын

Thanks

@amalfula2331 10 ай бұрын

Great

@MahmoudAbido 11 ай бұрын

Do you mean coolant or refregirant? They are different. The coolent is the colored water (green in this car) however the refregirant is the R134a that is used in the AC system. If you don't have enough coolant, you can easily add some in the coolant reservoir (usually it is in the passenger side). If you don't have enough refregirant in the AC system, then most probably you have a leakage somewhere. The AC system is a sealed system, so it should hold the amount of refregirant that the manufacturer added at the beginning. To check for leakage you can add UV dye to the system and rent the leakage inspection tool from AutoZone. Thus will help you to know where is the leakage. Then you can see what should you do to fix it. Thank you for asking. Let me know if you need any help

@user-ri2yo7kl2d 11 ай бұрын

So is this the reason my car doesn’t hold pressure and coolant ?

@yandia8336 11 ай бұрын

I appreciate your very detailed videos. You explain clearly how to do each step, even providing details such as torque specs. I utilized all six parts for the Mazda 3 AC system replacement and now have working cold air! Thank you.

@MahmoudAbido 11 ай бұрын

Thanks so much. I am happy to find this helpful. Let me know if you need any help