Great video!

Can you share the configs if possible ?

sir, as per this configured topology, asa unable to read the loopback addresses. why. but in your case its working. fyi iam using pnet lab

if you are having GARP and supress ARP, then what is the need to configure multicast ? once the endhost do GARP leaf using the control plane should send the info to other leaf and using Supress ARP endhosts can populate their arp table ? do you think without multicast it can work ?

Amazing explanation, very useful bookmark for my collection.

In the latitude longitude you forgot to write North & East Direction.

Hey I have a question.. usually AP are connected to some edge switch directly, because these are POE. Does AP still create the Vxlan tunnel?

Thank you for your video. How about using ebgp instead, what will be the routing behavior changed. Appreciate if you can show us some examples.

Could you please continue this series with more focused on troubleshooting the real time issues. It would be very helpful for the people who wants to learn silverpeak sdwan and do certifications

Very well explained. Thanks!

Thank you so much All your videos are great Could you please create a video about using VxLAN for DCI?

Great job .Thank you a lot .

Love you sir. Much much appreciated. Awesome explanation. Keep it up.

Any video on AOS10 virtual VPN deployment?

FYI - 42:36, I had run the "show ip route" soon after the e0/1 was shut. Hence you see the 10.0.13.0/24 (connected route) has been removed from the routing table and the route from RIP hadn't arrived on R1 yet. RIP sends periodic updates every 30 sec so you will see 10.0.13.0/24 ( RIP route via R2) if you run the show command again post 30 sec.

Nice content. Another point is, in some cases, we need to limit ARP responses for a given eth segment. This result more strict routing policy and we need to define at least two RIB entry which they are more specific than our eth segment. We can point to null interface for more specific routes but this isn't a good idea, so we will point to a trusted intermediate hop. Now the problem is, router no more have a next-hop reachability, since our ARP limiting specific routes points to any random eth neighbor. The solution is to add exit interface in our more specific static entries. This will solve our routed networks reachability and any traffic destined to next hop itself but we have new problem, any another intermediate hop in this eth segment also need to static entry since we are still unable to point any directly connected entry.

Great Video Glad for the video session 🙏

Thank you

I saw a few videos, your teaching skills are really awesome... teaching isn't matter how teaching is matter great is there any chance to start WLC and Wireless ?

In the pop3 you also need connection between RR's correct? I think thats missing from the diagram?

Another great video as well, is 5:30am EST and I am enjoying this video so much.

Joyal is a fantastic engineer and a trainer who makes learning very easy, first by designing, secondly by explaining the lab layout and finally showing how to make the technology work. Thanks, Joyal for the mentorship you provide through these wonderful vlogs.

I had to mute this guy. His voice so loud and panicky. His head is all over the place.

Hi Joyal, @ 13:40 , both wan interfaces were configured with INET1 labels for SP-4. However SP-4 had MPLS and INET profile. Doesn't it need MPLS+INET profile?

Can you share the path of ios xe image which supports telemetry

very low volume

My mac keeps having errors and says it can't download them bc it is from an unidentified developer

Hi ,how get orchestration silverpeak trial license?

Thanks for your vids! The test drive SD WAN was already configured with some edges, how can I request one without any instances, like the one you show in the video?

Hi bro, have you configured svi? I can't be able to reach to csr internal interface IP.

Great Content brother. Thanks!

This is very helpful and very well explained.. Thank you Sir for such rich contents ❤

Request to please continue for more videos, I am waiting

What versio of switch are you using and where did you download it ?

Great Explanation . Brushed up with basics and the set up

Nice intro - but how can you automate the address attribution for the sites behind the edge? Can you read from a database? Can you add variables in the pre-configuration file?

Thank you

Nice one

[ERROR] /home/stack/devstack/functions-common:2366 Neutron did not start

echo 'WARNING: this script has not been tested on focal' WARNING: this script has not been tested on focal +./stack.sh:main:237 [[ '' != \y\e\s ]] +./stack.sh:main:238 die 238 'If you wish to run this script anyway run with FORCE=yes' +functions-common:die:285 local exitcode=0 +functions-common:die:286 set +o xtrace

echo 'WARNING: this script has not been tested on focal' WARNING: this script has not been tested on focal +./stack.sh:main:237 [[ '' != \y\e\s ]] +./stack.sh:main:238 die 238 'If you wish to run this script anyway run with FORCE=yes' +functions-common:die:285 local exitcode=0 +functions-common:die:286 set +o xtrace

./stack.sh: line 61: warning: setlocale: LC_ALL: cannot change locale (en_US.utf8): No such file or directory

./stack.sh: line 61: warning: setlocale: LC_ALL: cannot change locale (en_US.utf8): No such file or directory

Excellent!

Hi, Does igmp multicast works on different version? Example: router on v2 and host on v1. Are those version backword compatible?

Hi Joyal, thanks for this kind of content.. how can I download Cisco ios/sdwan os for labs.. should I have a contract or we can have any specific licence or free.. need advice on this pls..

Good video thanks

Ru conducting ISE online course

Very Helpful thank you

where did the orchestrator is deployed as I am not seeing in the simulation ?