Ok..ok...1 min into vid and i hear " IMPACT"...PLZ GUYS..NEVER USE IMPACT FOR PLUGS..REMOVING OR PUTN IN!!!
@CocosPlayound21 сағат бұрын
🤣 trust me these are known for breaking off I used it to pull the little bolts holding coils in
@addictedcreeper11 күн бұрын
Ours was makin a rough rattling sound at idle in the water. Figured some rocks got sucked up in there from beaching it so often. Took apart the housing and a bunch of little pebbles fell out…. except they were shiney. Yeahhh those were the bearings. Completely cooked. Been trying to figure out how to get that nut off and was about to buy a complete new housing till i saw this and the tool to remove the impeller
@CocosPlayound11 күн бұрын
Hell yea I’m glad you got it figured out! Did you like my technique? 😂
@addictedcreeper5 күн бұрын
@@CocosPlayound too bad i ordered the wrong size one. Too big for the hole lol
@goldenliver02313 күн бұрын
What kind of resin and fiber glass did you use?
@CocosPlayound12 күн бұрын
Just the stuff that you can get from AutoZone, but I hear total boat is the best
@catfisher42016 күн бұрын
No better way to check the cooling system than stick it in some nasty gunky water to clog it up!
@CocosPlayound16 күн бұрын
Naa it’s clear just knocked some bark loose that was floating the pump intakes don’t really clog like people think.
@ToddleyProductions16 күн бұрын
Ask the owner if he wants you to send it to Jetski solutions! That ebox would look and run brand new! I recommend it
@CocosPlayound16 күн бұрын
He just wanted it running so I replaced everything needed and sealed her up.
@ToddleyProductions16 күн бұрын
@@CocosPlayound they rebuilt my 650sx ebox and it’s mint now
@kyleanderson976217 күн бұрын
What did you do about choke and fuel switches?
@CocosPlayound17 күн бұрын
I’m doing a primer where the choke was. Don’t need choke if you have a primer. I set it on reserve and plumbed it to carb. We don’t do full tanks and if we do I stop and check under the hood of my skis every hour or so to make sure everything is good.
@Hubjeep17 күн бұрын
My screen is awake, but the solenoid just clicks.
@CocosPlayound17 күн бұрын
Try crossing solenoid with a screwdriver if it turns over the solenoid is bad if it just arcs and doesn’t do anything, the starter is bad or the engine is locked up
@Hubjeep15 күн бұрын
@@CocosPlayound Thanks! I removed the top deck, found the starter looking very corroded. Power is getting to the starter, but is not turning. Ordered one on Amazon.
@catfisher42020 күн бұрын
We just sold an identical boat that we got at auction. It had a cracked engine block. Only had 125 hours on the boat.
@catfisher42020 күн бұрын
If you're putting wood into a boat then Every inch of the board should be covered in epoxy resin. Or make it all out of plastic.
@ajridge226424 күн бұрын
Do you not need the water running into the back when you're starting and engine running?
@CocosPlayound24 күн бұрын
You don’t have to if it’s for a very short period of time. No more than 20 seconds or so. You are suppose to start it after pulling it out of the water and rev it to clear water out of the system
@angryburrito741126 күн бұрын
Great series. Boat looks great. Gray looks stupid, should have gone with White.
@CocosPlayound26 күн бұрын
Place was out of white and white stains our family can’t have white stuff 😂 thanks for watching!
@zyrastolemyllama623129 күн бұрын
Thank you ! It fixed my no start problem
@CocosPlayound29 күн бұрын
Heck yea!!!
@lakelifeandbeyondАй бұрын
Great video!
@CocosPlayoundАй бұрын
Thanks for watching!
@finbah5706Ай бұрын
in the early 80's my Grandfather gave me a whole lesson on how Marvel Mystery oil is the answer to everything. I buy it buy the gallon ever since and agree.
@CocosPlayoundАй бұрын
Yes! Great stuff!
@englandentertainment1530Ай бұрын
Awesome video man! Hope to ride with you again sometime!!
@CocosPlayoundАй бұрын
100 percent coming back next year 💪🏼💪🏼
@Factory928ACАй бұрын
That was wild lol… did you run the 144 pump with this swap??
@CocosPlayoundАй бұрын
No just impeller
@melvinrawlings1457Ай бұрын
Dude u whistling after every little thing u explain is quite fucking annoying. I believe ur watching too much of vice grip garage. Because not only are u whistling and shit but ur also doing his little hand movements and shit as well. Be a leader not a follower bro😂😂😂.
@melvinrawlings1457Ай бұрын
Great content as usual. Keep it up. And much love to yall from Maryland❤❤❤.
@CocosPlayoundАй бұрын
Thank you!!!
@LindsayDuniaАй бұрын
I just bought my first (88)650SX 2 weeks ago. I'm kind of excited to try it as every time I own a JS, it does not run like my 88 440. I've never ridden a standup yet but have owned them they just never wanted to run in or near water. I'll give my 650 another chance in a few weeks when I'm off-call. If I can get my 88 650 and 440 to run IDK WTF, I will do with the 440. Hey, at least I get to learn how to ride on Lake Havasu in Lake Havasu City, AZ at Body Beach.
@CocosPlayoundАй бұрын
Make sure the fuel system is good on the 650 and it won’t treat you wrong! I say away from the other JS models now!
@LindsayDuniaАй бұрын
@@CocosPlayound oh. I have an SBN44 on the 650 with a Coffman pipe and I think waterbox. Someone modded this 650. Ya the JS lineup just seem problematic
@JetSkiBuyFixPlaySellChannelАй бұрын
Instead of open headers he's running an open hooder. Nice. Could be a mud dauber nest in the pisser.
@CocosPlayoundАй бұрын
Yeeaaaaa! Hahaha! Blew through all the lines and everything flows! Now that some time has passed I’ve figured out the culprit and it will be on the next video!
@teenafancihyatt6756Ай бұрын
😁🤣💫💫🇺🇸💫💫🙏🏼🌏🌎🌍🌎🙏🏼💫💞🎶🏝🏖 🍿
@taylorjames1127Ай бұрын
Makes me anxious watching a motor sink like that(Ik it's made to. Still tilts my brain).
@CocosPlayoundАй бұрын
It’s pretty sealed but the engine would still be above when doing those tail stands if that’s when you are talking about
@jemskee9188Ай бұрын
This is exactly how I want mine.
@CocosPlayoundАй бұрын
Watch my full video on here!
@cameronglidden794Ай бұрын
🤘🏼
@doublem6027Ай бұрын
Where's your 95 superjet?
@CocosPlayoundАй бұрын
Guy on lake Lanier bought it. We decided to keep the 650 my wife likes it better and it went to a very good home and he will preserve it
@englandentertainment1530Ай бұрын
Hope y’all make it out again some day it was great having yall out there!
@CocosPlayoundАй бұрын
Already thinking about September💪🏼 got a whole video coming of the trip
@squaredealshoes9964Ай бұрын
before this video even starts, i'm sayin yes.. beside the dust that thing looks completely unmolested.
@CocosPlayoundАй бұрын
Thank you for watching!
@estebanrodriguez5333Ай бұрын
Hi ! i have an issue with my 08 rxp x , i try to start it up with the start/stop button and it doesn,t work once i try with cables it starts OK ( i know that is harmful but just to test it was ok) once i turn it off with the start stop button it stops normally, we check selenoid and replace it and still the same issue, we check the startstop cable and might be OK , something a little bit strange is when i push the stop button it accelerates a little bit, also the strange thing is how the button works to stop the engine and not turn it on? thanks for your help! in addition the fuel gaugue does not show the level of fuel! appreciate your help!!!!!!!!!
@CocosPlayoundАй бұрын
Has to be button or battery or cable issue
@Redneckxican84Ай бұрын
What was your steps on polishing the boat minus pretty faded like yours was what did you use? Thanks in advance.
@CocosPlayoundАй бұрын
What I showed Just a cutting compound on a wool pad. Do a reasonable size piece then wipe it then do it a second pass
@HandlehandlebarsАй бұрын
If I woulda know mine had this junk I wouldn't have bought it...
@CocosPlayoundАй бұрын
It’s ok unless you slam somethinb
@JesseUnderscoreMartinАй бұрын
What were you priming it with? Pre-mix?
@CocosPlayoundАй бұрын
Yes
@Lego9215Ай бұрын
What grit Sandpaper did you use?
@CocosPlayoundАй бұрын
400
@Lego9215Ай бұрын
@CocosPlayound thank you 😊 🙏
@erichter66Ай бұрын
What is the part number?
@CocosPlayoundАй бұрын
I don’t have it I just bring it to auto parts store. I put it on the screen of what I could find during the video
@martinparker9249Ай бұрын
i call BS ....why would someone jus leave it neading jus a fuse ? i bought one in UK same as ....wouldnt run , had spark ....deduced crank seal gone .....POS £400 loss . must be because people in US are dumb and jus buy new on simple shit .......DOESNT HAPPEN HERE..... THAT OR YOUR SOME LUCKY MOFO
@CocosPlayoundАй бұрын
Thanks for watching from the UK! It’s sat for many years with the battery hooked up the fuse, just corroded. I don’t think that’s why it was parked. You watch the whole video at the end. You see me riding it and it started to overheat with a lot of air in the cooling system. I think that’s why it was parked. We will be getting into that in the next video.
@TheBehnkeFamilyАй бұрын
Thanks. Do you have the part number by chance?
@CocosPlayoundАй бұрын
I put it up on the screen I don’t know exactly
@lokksable2 ай бұрын
Can you start it with out a key?
@CocosPlayound2 ай бұрын
You can take the prongs off the ignition switch and get a new key and ignition switch shouldn’t be hard to find. In the meantime, you can look up what wires go to and touch the wires together.
@TheZammy2blood2 ай бұрын
Just finished the series! Loved the videos! Gotta say, your boy has better camera skills than i ever did at that age 😂
@CocosPlayound2 ай бұрын
Yea I was kinda shocked myself! It’s been a year and he wants to help more and more maybe I made my own camera guy!
@marissamelchior32592 ай бұрын
Does that piece work on trixx models too?
@CocosPlayound2 ай бұрын
Yes
@marissamelchior32592 ай бұрын
@@CocosPlayoundok!!! Thank you. Mine just recently stopped starting so hopefully this works!
@CocosPlayound2 ай бұрын
Yea it’s battery that relay then starter is how I’d check the electrical
@marissamelchior32592 ай бұрын
@@CocosPlayoundOk
@terrymaine41212 ай бұрын
Heck yea!
@CocosPlayound2 ай бұрын
Thanks for watching! Hope you subscribed!
@badm0t0rf1ng3r2 ай бұрын
Oh heck yeah bud.
@CocosPlayound2 ай бұрын
Heck yea duuuudddee thanks for watching!
@badm0t0rf1ng3r2 ай бұрын
You throwing the ski around up in Michigan?
@CocosPlayound2 ай бұрын
Nope. Covington Louisiana wayyy the opposite way 😂
@badm0t0rf1ng3r2 ай бұрын
@CocosPlayound was curious based on the registration! Awesome stuff man. Subscribed.
@CocosPlayound2 ай бұрын
@@badm0t0rf1ng3r Wisconsin is the shit. I have a fleet registration account with them so all my stuff is registered through there
@potatoboy765-qm3zh2 ай бұрын
wish i could just do this
@CocosPlayound2 ай бұрын
All you gotta do is get your hands dirty!
@BonBon7702 ай бұрын
Nice!!!
@timothysims2 ай бұрын
What is the blueberry juice?
@CocosPlayound2 ай бұрын
Some premix 😂😂 just looks like cool aid
@doublem60272 ай бұрын
Video is blurry homie
@CocosPlayound2 ай бұрын
When I play it’s not let me see what I can do
@CocosPlayound2 ай бұрын
What is your quality setting on?
@badm0t0rf1ng3r2 ай бұрын
@@CocosPlayound Its pretty clear for me and I have it on auto. Maybe they got to it before the HD version was completed processing.
@alexmiller59252 ай бұрын
Looks clear to me
@BigDipper792 ай бұрын
It’s not blurry. His Biden phone has a slow connection.
@juanandino91362 ай бұрын
Hello, nice video, I have a GP 1200r Smokes a lot and also there is a lot of oil on the bottom of the jet. Do you recommend I should do the same?
@CocosPlayound2 ай бұрын
Yours is still oil injected?
@vergis942 ай бұрын
Thanks for the video 🔥 I pulled my 94 Seadoo xp engine and put the time back. I noticed when I move the rotary shaft back and forth there is a little play, do you know if that is acceptable??
@vergis942 ай бұрын
I guess the question is how much play should it have
@CocosPlayound2 ай бұрын
Not sure that would be checking the manual kind of thing but I’m sure it’s supposed to be very minimal. The brass is probably wearing out.
@timmy2dogsable2 ай бұрын
I'm working on mine right now. Thank God I found this. I'm thinking I have to pull the crank. I bet not now. Thank you
@CocosPlayound2 ай бұрын
The reason why I do it!!! Thanks for watching
@sjbadalamente2 ай бұрын
After 30 years of waiting, this SuperJet has been released to the wild 😀... never a dry day
@CocosPlayound2 ай бұрын
Yeap! Glad you have it. I want to make some riding videos up there at lake Lanier
@zacksyakov87172 ай бұрын
Mine isn’t that thing do you know what else it could be?
@CocosPlayound2 ай бұрын
Make sure your starter is good or engine isn’t stuck. Could be something in the jet pump also dont over look that