I got ABS code C1218 I replaced the wheel bearing sensor on the front driver.

Leave a classic car, classic. Computers and sensors and fuel injection doesn’t make it better. It just makes it harder to work on.

I need to know how he used his hand to shift it into neutral

Good demonstration of electrical shorts. A lot of people's dont understand the danger of overloading a circuit.

Why wouldn't you replace the o rings while its apart?

First 4 minutes useless

Excellent video! Thank you for keeping this video online. It was much needed information because everyone was a Google technician, and I was getting different instructions for the same thing. This video got me back on the road again!

What’s the part number ?

Do you guys sell battery cells?

WHAT WAS THE OUT COME??? VOLTAGE OK? DID YOU NEED TO RE-SET ANYTHING RELATED TO THIS REPLACEMENT? DID EVERYTHING WORK FINE? 🤔🤔🤔

You just have to love that they put an important thing like the AC-compressor so available and easy to access in the Mustang. Just take a look at any German premium car and they basically started building the car around it (well not really, but far from easy access) 😁

A lots of talk with zero details

I believe it was 1994 when R12 was banned.

That’s weird autozone advanced or orileys could not get ball joints for my rsx

Good info. Would have liked to seen the 12v battery test you did at the beginning, again after the new hybrid battery was installed. Did it fix your battery charging issue or not?

Awesome camera angle.

All these videos fail because they just say go spend 1000 - 1500 bucks on a new valve body. HOW DO YOU REPAIR THE VALVE BODY??

Need help

Aircon Systems had always confused me. But your straight to the point education on 'Understanding the System' was awesome! Not even more than 5 minutes to explain how it all runs. Thanks and cheers!

Can't do it without an expensive scan tool? WHY the f do you even do these shows then?

Very helpful to learn the functions of the a/c system and how it works. I had my condenser replaced in a shop. Do you think they would have replaced the orifice filter?

Readjust the lip seal spring to be a tad tighter

what size was the wire? and did you need a fuse for this winch?

What is a "compresher"?? English bro, the only language you know..

My mom's 2008 Buick Lucerne has the exact same problem. Hopefully this will work. Can you please provide me the parts number information for that seat? Thanks for the video. It's helping even though it's a different vehicle and seat.

Odd things about this video. They did a leak check with the drive shaft out. They had to go buy a piece of cardboard.

Can this be done on 1957 Chevy 283v8

These guys are on point! I learned the hard way. Always change both the seal and bushing.

The Prius has always been a series-parallel hybrid. Toyota literally coined the term "power-split".

I’m sad to see you use the Cobalt stamped steel LCA , the HHR has forged aluminum lower control arms , they different in that the lighter Cobalt is not strong enough for the weight of an HHR.

Can we use it in Toyota 3y , 2 liter petrol, carburettor engine with rare wheels drive

So bleeding the brakes after isn’t necessary or was tht another step you guys didn’t explain?

Expantion valve likes valve can throttle if Clogged?

What about the clip on the cable by the shifter?

Many thanks for the education!!!

What's the part number of that peace that u replace

how did you torque those bottom bolts?

I need guidance from any HVAC tech please. I replaced the expansion valve and the filter drier. With the engine not running the gauges read 60/60. Once I run the engine and turn the AC on the compressor clutch runs and the condenser fan spins but the low side goes into a vacuum and the high side goes to 80. The expansion valve turns to a block of ice.

So does the bushing cause a vibration on the rear end so I replaced my seal three times and I’m like why the hell does it still leak? I’ve noticed it splattering on my truck so now watching this video. I wonder if this is causing my issue also, I feel like I have a vibration but it’s more on the rear.

Your not telling people what year this truck is !!

Link of the clear coolant hose

NDE inspection

How do I determine the correct shock on an air bagged S10

How many ohmics is it supposed to be, did you guys make this up?

I have a bad seat motor....this is no help at all!! I need a video on fixing and replacing GM seat motors.

Do you can give work permit, i from Bangladesh, i can do automobile

This is literally what is happening to me and earlier it was fine. I think I am going to have to pay to get it looked at because I don't have the tools or the man power to be picking up a whole seat on my own.

Sorry this video was not linked to the previous video about the seat repair. I was able to get it from the channel searching it out.

So do you bleed the brake system before removing the old module or only after the new one is installed?

My wife and I are picking up a used 2014 2500 5.7l Tradesman Crew Cab 4x4 with 18,030 miles on it. This truck has VVT so this is going to be important to know! Thank you for posting this video.