Spark plug socket drill a hole through the socket tap it and put a grub screw with a allen head
@sleepercell992610 ай бұрын
I did that. Total bitch of a job
@stevene5194 Жыл бұрын
This design is NOT what you want unless you drive like a old lady, Over time even with thread locker that bolts work their way loose and causes the collar to widen , wobble, and will not tighten up again. Look for the type that has 2 bolts that hold the collar tight on the shaft, and 3 bolts to hold on the pulley.
@emersenandreasen8457 Жыл бұрын
Hey oz mini you still got ur mini cooper s ?
@jaysemartinez2943 Жыл бұрын
UNO you could have just taken the rubber out of your socket and just tightened the plugs same way 😂
@zokusharuuku1091 Жыл бұрын
When your spark plug socket comes off you just have to put the extension back in and try pulling up at and angle wiggling it.
@TheRedgtv20002 жыл бұрын
The cars body is so clean, so lucky to live in a warm climate where there is no salt. I also enjoyed the property and the quietness!
@ozmini69682 жыл бұрын
Thanks for your comment, yeah I’m lucky I got a clean car. Not leaving in a salt environment really helps under the car and rust. Cars in Australian weather are pretty good in that regard. I’m really surprised when I see cars in UK where there’s high salt. Yep again lucky to live in a bush block!
@johnhibbs65082 жыл бұрын
Your video production skills are excellent!
@johnhibbs65082 жыл бұрын
]Great mod list. Don't forget the de-carbon the intake valves. Could add 20 HP! I'm going to use Bg valve cleaner from ebay.
@johnhibbs65082 жыл бұрын
I just bought a R53 2006 here in San Diego. I have lots of plans for mods. Watching lots of KZfaq videos. Should be fun.
@johnhibbs65082 жыл бұрын
Are there any ECU changes? Are you going to change out the camshaft?
@johnhibbs65082 жыл бұрын
How do you film from your head?
@johnhibbs65082 жыл бұрын
My R53 has 100k miles so I plan to clean the intake valves. Using chemicals instead a walnut blasting . Going to take off the intake manifold. Maybe I should start my own channel. Is it hard?
@johnhibbs65082 жыл бұрын
I just bought a R53. My first project car. I plan to install a 15% too. Your channel is perfect for me.
@DavidLopez-lh8gd2 жыл бұрын
Love the animals in the background please post a video of them just subscribed !!!!
@brianrabbit71592 жыл бұрын
I did 19% it was amazing
@SkyPirateU2 жыл бұрын
@OzMini Are those special heat resistant stickers? How have they (the stickers) held up over time with heat cycling?
@PekanOsijek2 жыл бұрын
Now after a time do you would say the 17 would be better? Or what would you prefer? Whats the big different between 15 and 17 ? I thinking of make the same move an dont know if 15 or 17...? What would you say...thank you great video
@ozmini69682 жыл бұрын
Hi Pekan, I’m really happy with the change the 15 made, it’s a must upgrade. I can guess the 17 would give a little more midrange pull, it’s roughly 2 psi difference so I should notice it if I did it. If taking on a track is your aim I’d say stick with 15, because a 17 will generate more heat. If it’s a road only car maybe go 17. I think at some stage much later I might try a 17 just to see first hand if with an upgraded inter cooler I could get get the most out if a 17
@PekanOsijek2 жыл бұрын
@@ozmini6968 thank for the answer. It should be only a fun 2nd daily. Heat should not be the problem for maybe 4 pulls in raw. And little bit fun on curvy roads. Upgrade cooler maybe go in one when i am at the mechanics. Thnaks for the infos
@K03sport Жыл бұрын
You can also do a +2% crank pulley. Turns the 15 into a 17 and the 17 into a 19. But as said, more sc spinning generates more heat and wears on the sc gearbox more
@davebalaam2 жыл бұрын
Cracking video. Definitely something I'm looking to tackle in the future. Quick question regarding using the puller: would applying some heat to the pulley before fitting and using the puller help with the removal of the pulley, or is it difficult to do that without setting fire to something nearby?
@ozmini69682 жыл бұрын
Thanks I’m glad you liked the video. Hear may help the pulley but not the puller. Honestly not sure. For me the chain vice grips was the key, clamped down as hard as I could. Alta sell a different style puller that could offer a better clamping force but didn’t try that.
@Niki_R1882 жыл бұрын
You could put the new plugs with the existing spark lead just to get them to catch half a thread and then take the bloody rubber out of your tool to make your life easier..been there done that..
@ozmini69682 жыл бұрын
Ahh, didn’t think of that! Good idea! 😁
@alexalpizar40962 жыл бұрын
hi my name is Alex I have one Mini Cooper 2002 ,wher you bye this pulley?
@ozmini69682 жыл бұрын
Hi Alex, I actually bought this pulley off Amazon direct from the US. You can get similar quality pulley's off eBay as well, even suppliers in Australia (but they were a quite a bit more expensive for me believe it or not.
@hasaelmonty75312 жыл бұрын
Pretty nice video very informative
@ozmini69682 жыл бұрын
Glad you liked it
@hasaelmonty75312 жыл бұрын
Would like to know where did u get the red trim of the bottom grill please reply
@ozmini69682 жыл бұрын
Hi, the red trim was on the car when I bought it, I think it was aftermarket. It looks like it was just a think plastic strip stuck on. I've actually replaced the front bar completely with a new one (someone backed into me) so its now gone
@hasaelmonty75312 жыл бұрын
@@ozmini6968 thank you so much replying back
@MrSamourai772 жыл бұрын
Hi! Good job👍 did you made a remap after pulley upgrade? Thanks
@ozmini69682 жыл бұрын
No, no need for a remap. I do have a Cam to go in and that will require one though
@bluedunn3743 жыл бұрын
What brake pads did you go with?
@ozmini69682 жыл бұрын
There’s a bit of a story to that! In a coming video…
@FearTheHonkin3 жыл бұрын
Hello! Greetings from the US! I was looking at your budget/list of mods and I am curious if you purchased the crankshaft pulley yet. I had a conversation with Way at Way Motor Works and he mentioned that the 2% overdrive pulley is meant for JCW or stock supercharger pulley sizes. The 2% overdrive size should not be used with a supercharger reduction pulley because it will make for an odd belt size which may slip when the engine is under heavy load. If you plan on getting a crankshaft pulley, I wouldn’t use the overdrive option. I picked up the 15% reduction pulley and the standard size crank pulley with harmonic balancer and the belt fit perfectly so far. Hope this helps you!
@ozmini69682 жыл бұрын
Hey, sorry for the delay in getting to a reply. Ok that’s different from what i understand as I’ve seen people running what I was thinking. That’s one thing I haven’t bought yet, although I have literally been looking at the WMW one. You’ve now made me stop and checkout whether it is suitable, so thank you I’ll need to sink some more time into research on this one. I was assuming I could use a 17% equivalent belt as a note.
@nicolaisadowski87873 жыл бұрын
hey, where did you get the rev counter for the middle? or did you build it by yourself? 🤙🏽 great vid!
@ozmini69682 жыл бұрын
Hi, no not aftermarket. In Australia the middle rev counter is standard for this model. There is another version that has what's called a Chrono Pack and that has three gauges in the middle instead
@waterlover3 жыл бұрын
Do you have a link to your intercooler? Wanted to know where you got it
@ozmini69683 жыл бұрын
I don’t have a link anymore but it’s just an eBay intercooler, which made an immediate improvement. I’ve now installed a “not so hobo” diverted which has made it even more effective which I’ll show in another video coming
@waterlover3 жыл бұрын
@@ozmini6968 diverter? Really have to see a link to that video want to get one too.
@GloriosoMD3 жыл бұрын
Just be aware that if the SC has a lot of milage on it, it can shorten its life. I did mine and 3 months later have to change the SC 😔
@ozmini69683 жыл бұрын
Thanks for the feedback, hopefully mine should last a while as the car has a little over 110k. Although I am thinking of doing a service on it
@JexL923 жыл бұрын
How many miles was on your Sc?
@GloriosoMD3 жыл бұрын
@@JexL92 185k km.
@JexL923 жыл бұрын
great video, makes me want to install one also
@ozmini69683 жыл бұрын
Thanks, it’s a great upgrade, makes a noticeable difference for sure
@derekbond35123 жыл бұрын
You know what this is a really good rundown on what to do to improve the front upgrade, I'm just about to do this myself , I have all the parts in original messy condition so onwards now to hopefully get mine to look like yours, all the best from UK
@ozmini69683 жыл бұрын
Thanks, it’s all in the prep and cleaning prior to painting, the more time you take there the better the finish, good luck with it
@stevewalker98883 жыл бұрын
Sounds like patience is something you need in abundance, when working on a mini. I just wanna get in and have fun in mine. So would have to buy the new-ish callipers a week or 2 in advance , the ones on the car when I bought it are neon green and hideous.🤢🤮. Thanks for sharing dude. 👍 liked and subbed. Stay safe and stay awesome 😎
@ozmini69683 жыл бұрын
Thanks, I think the more I’m working on the Mini the less intimidating it’s becoming and easier, stay safe too
@darrentrishsummers4 жыл бұрын
Good on you Shaun. I’m looking forward to following the journey and seeing what you do to the mini.
@rohanthomas42974 жыл бұрын
Nice work Shaun, looking forward to seeing what’s to come