What state u live?

There's nothing special about a brake job so 150 per axle is overcharging the customers, specially because it don't even take an hour to perform the job.

You’re not only paying me for what I do, you’re paying me for what I know. Also, as a mobile mechanic, you’re paying for me to come to you and do it where it is no matter the weather.

Actual footage of the cameraman getting harmed. Oh wait nvm it was just only the camera.

I live in the rust belt(Quebec) shit get insanely rusted here. No anti seize on my rotor. I just apply some PB blaster around the studs holes and into the center, leave it for a couple of hours while it bakes in the sun and do its thing. Two 6lb light hits and boom its off, its really that easy just let pb blaster work its thing

$20 break jobs

Over priced 100 for both sides is still good 150 for front and back

Brakes, just pads and rotors, is one of the few jobs that I can still perform on my own car. So when it comes to the wheel end of the brakes, I will do it. If it is an ABS problem, I have to see the mechanic.

In Missouri, labor at a Chevy dealership is $210 obviously with parts it is considerably more. Usually $525-650ish for pads/rotors depending on vehicle type

What can happen if you put the oil where the dipstick is

Bro get some WD

Every mechanic has the right to add his value. Yet still, they are persons who get quality break jobs done for free

Link for the red grease you put on the outside of the pads? Thanks man

Looks like quality work with quality parts, at that point the price is justified IMO.

Just get a bigger hammer

Thats shop rate with no over head wow expensive

Any thoughts about using a 10W40 non synthetic oil for a high mileage E46 that burns some oil?

What kind of drill bit do I need to remove the panels to put in the regulator

I dont anti sieze the clips.... they arent that hard to get off and you definitely dont want them popping up and siezing the pads

'Don't get any of this on the studs.' Proceeds to paint the studs.

🤦🏾‍♂️🤦🏾‍♂️🤦🏾‍♂️

I just try to put it on the studs only, it then automatically gets all over everything else 😊

Parts included..?

Silicone is a sealant and cause sticking.

Where do you jack from so that you can use the pinch welds for your stands? Near the end of the video it looks like your floor jack is near the control arm?

I do my own. Not hard

Super over changing 🤢

You must be spending an hour on each caliber...

What collects dirty and debris? Anyone?

When you compressed the calipers you didn't open the bleed valve? I thought that wasn't good for abs brake systems.

What you call a $250 quality could be a $50 quality to someone else !!

The location of the oil drain plug looks intentional in a bad way lol. Like they wanted it to be challenging.

Cant you just change the ball joint?

Thats why use copper anti seize spray

Do you not have to replace the screw you cut from the rotor? Thanks

Do you have a video for the front brakes? Thank you.

Changed the pads for $50 a few weekends ago. Pretty easy, just gotta get dirty.

No hate bro but ur talkig about quality , i noticed u didn pinch the caliper hose and opened the bleeding valve so the old fluid in the caliper will b remove , that a procedure needed on car with abs , windings caliper back like u did could cause back pressure on the abs module and damage seal ect , just saying again no hate

🤣 he is insane

Sounds cheep. I spent 500 in parts on my last brake job

If you want high pay go to a track. This brake change cost is too high for the actual labor involved. I can only imagine the rotor cost change.

This video was so well done. Torque specs included too, bonus. Love the Avenged Sevenfold background music too.

Awesome bro that's why I had my power down I thought it was under the intake good video good video

this is more for diy jobs, I don’t know if they do that if you take it to a random mechanic

I APPROVED THIS VIDEO! WELL DONE SIR, I DO THE ANTI-SEIZE ALWAYS.

Need change it

Its bad brake

10 months later and still Foh boii pass me what you smoking +$200 an axel 🤣🤣

Weld a nut on it and it’ll come right out.

Nice work! Thanks for sharing your knowledge.