Glad they helped!

It’s a lifesaver

You can do it!

I would start with the transformer for sure

My pleasure

You are welcome

Glad to hear that

Glad it helped!

Not that I’m aware of

Yes, I go through the eye and knot it once

Intersting, thanks for the input

What I use does not require 3 phase and it handles the blaster just fine. And it’s definitely not a mobile/portable setup, which hopefully I didn’t lead anyone to believe that

Agreed :)

Glad it helped!

Glad it was helpful!

It does work, but I had no hand in that. I usually research a professional record player repair near me for help

Glad it helped!!

Thank you very much!

eBay. Those parts still exist on their new models. They typically don’t change the mechanism design, but they don’t know how to figure that out for you unfortunately

Thank you!

eBay, recliner-handles.com

That’s the route I would have gone. The foam may need to come out and be steam cleaned as well

My recliner mechanism works but wont lock

Glad it helped

🙌

Most of them don’t have any adjustments. You can tighten the KD brackets. You might look into replacing the springs with ones with a different tension

@@the323vlog4 it doesn't have springs for the back of the chair, just the footrest so I'm not sure if a whole different mechanism will fix it. I wish they had springs in the rear of the chair for the back rest. Any ideas? I love the chair but this is irritating. I have to climb clear up on the back of the chair once I get it reclined to try to keep it in place but if I breath the chair goes back to the sitting position.

Sounds like a tension issue. Maybe the spring is too much tension not allowing It to lock in place correctly. I’d also check to make sure the footrest isn’t interfering with the arm frames

@@the323vlog4 Is there anyway to adjust the tension? I ended up putting a couple of nylon wire ties around the frame to hold it place.

It’s hard to tell without looking at them. I always start with inspecting. I open up the dust cover of necessary and see if the arm is accessible. Sometimes there is zipper access and other times there is not

I have slower more in depth ones

Very welcome

I would replace the whole port

I don’t hardly use mine for latex paint removal. Unless it’s in terrible shape(the paint) I don’t think it would come off very easily

I wouldn’t expect So. It doesn’t work well on paints

@the323vlog4 thank you

Found this on the web... Yes, soda blasting can remove paint from many surfaces, including cars, brick, and wood. Soda blasting is a non-abrasive, environmentally friendly method that uses compressed air to shoot sodium bicarbonate (baking soda) at the surface being cleaned. When the baking soda particles hit the paint, they explode and disrupt the surface without damaging the underlying material. Soda blasting can also remove other coatings, dirt, grease, and stains.

@@the323vlog4 found this info on the web... Yes, soda blasting can remove paint from many surfaces, including cars, brick, and wood. Soda blasting is a non-abrasive, environmentally friendly method that uses compressed air to shoot sodium bicarbonate (baking soda) at the surface being cleaned. When the baking soda particles hit the paint, they explode and disrupt the surface without damaging the underlying material. Soda blasting can also remove other coatings, dirt, grease, and stains.

I’d start by making sure no wiring was damaged, then trouble shoot the switch, transformer and finally the motor.

It costs a little more to operate for sure but saves so much time comparatively . My labor is much more expensive than the cost of goods don’t makes sense

You may have a finish that is still very resilient. It work a lot better on worn out antique finishes

I have only seen them sold as full mechanisms by vendors. That being said, eBay would be the best resource to find them being parted out.

Sounds like something may be hooked up incorrectly, Like it’s getting constant power

Good question, I have no idea! If it were me, I’d spray it with degreaser and then blast it

Not quite sure. I’d have to evaluate it

I use a 80 gallon ingersol rand

Does it need an air dryer?

Thanks!

I’d say around an hour or so of blast time

Hope it goes well!

I usually just buy a generic one on Amazon and they work fine

I would imagine so, those are well Designed. I can’t remember on This one. Probably rooms to go or Ashley’s

amzn.to/3WZ15wj

Glad you liked it!

Thanks!