Would it be possible to to a 125 Box comparison. As there the Polini seams to rev much lower. A powerful Vmc 187 setup would be cool then test Polini, Malossi, BBS V2 and Sip road 3.0 Maybe with Rotary and SI 26 as originality and Box exhaust seams to make sense.

The option for converting for the pinasco casings using m6 threaded bolts is surely a better job.

Yes, its time i go from points! Which setup best. Sip road ignition or piaggio setup sip touren flywheel 1800g? Its for quattrini 172 setup. Touring..

This just heped me open up my Rally! Big thanks 🛵🥇

What does the lip do on the corteco seal?

For small handpieces, do you use a foredom?

Hi I am trying to use the toothed connection 65/24 type in a Malossi case( it comes with the auto mix stud), have you tried the toothed one in an auto mix case with no issue???

Is this setup going to be reliable/durable ?

Another great video, I wish the PX 200 engines where easier to find.

The sound of the simonini!!!! How was the performance though?

nice vid. are you still active in this world? cant find that tool anywhere.

how much oil does the vespa piaggio lx 50 2t take in the gearbox? Thks

Ok, I wont attempt it this way, looks totally random, I will move on, Thanks anyway. I hit the Like button

ya but how do we fix vibration issues

Buenas noches, yo acabe de instalar un amortiguador bitubo nuevo, pero no realice ese ajuste que se observa en a los 56 segundos del vídeo, es importante realizar ese ajuste, podria explicar aquello por favor, se lo agradezco

so gut , danke! bin heute mit meiner suzuki address erstes mal länger mit topcase gefahren und hab mich mega erschrocken als ich kurz die hände vom lenker genommen habe. normalerweise hält sie super die spur aber durch das Topcase ist sie vorne wohl wirklich zu leicht.

Do this work on 50cc ?

Hi, how much liters have the reserve of v3?

Did you have to alter the malossi piston

Can you please tell me if you bettered the fuel usage. I am thinking of mounting the dr pulleys in my original SH300 2013. I know have stock 19 gram rollers. I would like the rpm to go down on the highway.

I had exactly the same problem, 4 stroking, very rich 0-25%. I found out I already had AS264.... I also checked the swimmer. The solution was setting the needle down 1 notch. worked perfectly. thanks for getting me on the right track!!!😁

You must try the exaust from francesco ragucci...I have earned everywhere.

Hi i have just fitted the same clutch in a running engine, but when the clutch is tightened down it locks up the gear box. do you have an idea why ? everything seems to turn ok while the clutch is loose Regards Mark

La pregunta es donde venden esos balancines y que modelos de motos lo utilizan?

Hi mate been watching your videos for a while now and I trust you judgement! What’s your opinions on putting a kit (malossi 210 or something) on a mk1 Vespa p2?

The new SIP Vape comes with the regulator. Is it necessary to install the regulator that are provided in the set?

JB weld is my favourite epoxy to use.

What metering rod did you use for the 306? EF-26? I've got the SC2 28mm ready for my VMC 244 > 252...

Dumb question but when you have the selector rod as far out as it will go and attach the gear selector box should the gear selector box be set in neutral? Thanks.

Sorry just wanna know, do you removed the right centre stand spring? Cause I'm also using polini box, and the right spring centre stand is friction with the top side of the box exhaust.

Moin das Drehbohrgerät gibt es noch größer Von Bauer haben den größten lb 50 den steuer ich

Just the relaxed tuning state for going on relaxed Sunday cruises

Polini box continues to reign.

how much is cost ?

Wow,,,

Mantap pak

Transmission ratio?

Loctite 5923 might work to keep the gasket in place and to seal the cases.

Würdest du auch 2024 bei PNP Tuning noch zu einem VMC 177ccm Stelvio raten oder hat sich deine Meinung geändert? Ich überlege von meinem DR zu upgraden:125 E Lusso mit 24 SI und SIP Road, sinnvolle Entscheidung?

what..? 220 ml..? i use 500ml for all my 150 2 stroke vespas.. since i have vespa in late 1998 till now, i change oil 2 - 3 month, depend on how often i ride it..

What would you recommend as plug&play update for my P200, this SIP or the new Polini 210 cast iron?

im using 10 inch tire../ 4th gear 36 on mainshaft and muffler polini bigbox what your suggest for ratio ? is 23/65 or 23/64..?

Hello Mr Freakmoped! Thank you so much for your time and effort in putting videos like this together and sharing your knowledge. Much appreciated❤ Question - worth drilling to 2.5mm even if running a more stockish setup, e.g. only Sip road 2/3 with stock cylinder. Maybe with a DR177cc? AS IS 2011 PX150 w catalytic exhaust. SI20:20 carb.

Done the whole package: 60mm crankshaft, windows adjusted, exhaust raised 2mm, 0.5 head gasket. Runs with SI24.24 and Polini box. Accelerates nicely, feels like th peak power is around 6500rpm but as soon as it reaches 6800rpm it dies a bit and won't accelerate any further. Feels kind like a rev limiter is activated or the clutch starts slipping (but it's not). I've swapped stator, flywheel, CDI and tried to move ignition timing to 18deg but it still behaves the same. Any clue what could be the problem? It always happen exactly at 6800rpm, regardless uphill or downhill, choke in/out. The engine feels like it still should have a lot of power, the performance cutout is immediate. Is it fuel supply problem? (done only 2,5mm main jet drilling, and short fuel hose - fuel tap not modified) Wrong jetting? Or just the original cylinder limitation? (ports cross section etc.)

Is this the pinasco 251 engine

Really good that box. Always wanted a box but something I love about an expansion pipe. Maybe this is the solution

Cant find your video on the polini cast iron kit about jetting.

Hello from Barinas Venezuela, is possible to do this mod with a Malossi 177 sport cylinder ? Thanks

does the air bleed automatically after a carb cleaning? or do we have to unscrew the lid untill it comes all out?

How to orient the spring pin on the pressure plate? Which end goes to the small and big hole?