Where is 2 nd light bulb in refrig for a side by side.
@user-uy1um8ne9o13 сағат бұрын
Many thanks
@abidfarooqui489913 сағат бұрын
But why does the high limit thermostat button trip multiple times to start with?
@user-uy1um8ne9o13 сағат бұрын
Thanks
@ramlin3514 сағат бұрын
Mine still didn’t work Not sure if I got a defective replacement or if it’s something else
@kathy859014 сағат бұрын
What is different about the new one???
@yannduguay282615 сағат бұрын
Thank you so much very helpful....you make it look easy ....the retainer clip took me 15minutes hahahha
@user-dl6lh4yk3e15 сағат бұрын
Thank you very much for such useful information!
@Mike-su8siКүн бұрын
My bogging down problem on my husqvarna 122 hd 45 was just the bad gas filter line. That trimmer sure uses a weird looking gas filter I've not seen before til then I wasn't gonna check the spark arrestor the trimmer is to new for that to be dirty and i didn't check that doesn't need done plus it wasn't having a start up or stalling out problem it had a bogging down problem while i had it aimed upwards in the air it was bogging down then would just shut off i reset its high and low 2 years ago so i know it wasn't that. Some people should know if they don't know your little spark plug coil can burn out on those just like on any other small engine stuff doesn't last forever and at some point needs new parts or used parts they work to. But a stalling out problem is usually a dirty carburetor or your little rubber gasket at the back or bottom of the carburetor in it could be the little round screen in the carburetor is full of dust could be a dirty air filter could be bad gas for it to stall could be needing the h and L reset to I had a bad coil on weed eaters before so i know those do go out my weed eater been needing a metering diaphragm in it for a year now but i don't like weed eatering so i don't care to fix it and keep using it how it is
@loudspeakertestsmorebyaida3804Күн бұрын
I love Samsung appliances.
@mediamilitia7572Күн бұрын
Just replaced mines!
@geechee9385Күн бұрын
Just replaced my seal, had this video open whole time. Thank you so much! It is a little harder than on the video, but instructions were excellent. Had to go look at old seal to see where spring went (marks present) to be absolutely sure - sure don't want another leak! Clamps to assist with spring replacement are a must, I got 3" Ponys from Lowes, very cheap. Highly recommend this video.
@robcampbell3235Күн бұрын
Great vid. I wish every repair video was as clear and concise as this. Thank you.
@user-np6it6tk8dКүн бұрын
Rest my washer
@The_lucky_wifeКүн бұрын
Dirty coils outside- frozen coils in freezer inside! All fixed now- thanks!!!❤
@SabrinaTucker-w5tКүн бұрын
Do you have a video for the model FHWW083WB1
@masamune..Күн бұрын
Thx for this video! really appreciate it! :)
@LittleYokiКүн бұрын
All this to change the hose??? I have a small hole spray water every lmao this is nuts
@marsdiggy8Күн бұрын
Kitchen Aid blows
@el1743Күн бұрын
Perfect video. Showed repair was much easier then found on other where machine needed to be tilted and moved to get rods out. Fantastic instructions.
@heribertomojica9308Күн бұрын
This video was very helpful thanks 😅❤
@paukhansiamtonsing8707Күн бұрын
Where can i get the new sensor
@soundattentionКүн бұрын
Thanks. Replacing this thing with a Bosch 800 and you made removal easy!
@iggster433Күн бұрын
Thanks for video!
@MuswellКүн бұрын
I've ordered & received the Electrolux pump. I really hope I can do this. There are a few things I'm not sure about -- removing & replacing the spring retainer around the rubber seal, removing the detergent dispenser, that socket screwdriver thing for the bolt, & the different electric connectors to the pump. Gosh - we'll see.
@MuswellКүн бұрын
On this video - what is the other pump & hose next to the water pump?
@River_dawg2 күн бұрын
What is the purpose of all the foam insulation? Is it for the electronics or something else?
@NickPepe-t9o2 күн бұрын
I have a double oven with a F2E1 ERROR. Any idea of the root cause? Nick
@gallyarteaga87982 күн бұрын
Then only way we got ours out was to remove the bolt spray some w-40 and turn it on to drain and spin and it loosened up. I thought if this doesn’t work I’m going to have to jump in there and pull it out like there other person did in the comments 🤣
@sixdouble532one2 күн бұрын
Thank you for this video. It's the exact model I have. New belt replaced in under 30 minutes.
@lgbnz2 күн бұрын
front loaders suck. mold factories
@andrewross1942 күн бұрын
No mention of the fact that 316536621 does not come with holes pre-threaded.
@dalesatterlee48082 күн бұрын
It’s not as easy to do as the video depicts! The two minute video took two hours plus a pry bar!
@jeshaulis2 күн бұрын
Great instructional video. Very thorough and did not assume anything that the repair person already knew. I am going to order my pump from you as a way of saying thanks.
@Nick-mm9dg2 күн бұрын
Thank you. I was having trouble figuring out how whirlpool wanted me to take the console out.
@joepacheco79792 күн бұрын
Thanks for making this video! Although the part is hard to come by, at least I know it is very accessible/swappable.
@danyssolorzano76892 күн бұрын
what is the that little black rod on the timer? that rod chipped off on my timer and now my dryer won't work efficiently. ordered a new timer and just watched this video.
@rolandthethompsongunner642 күн бұрын
Why doesn’t unplugging the switch shut off the engine? Mine is stuck in the on position but switch clicks doesn’t seem bad.
@jamesa.hyerczyk65332 күн бұрын
I cannot get the block on, it doesn't seen to go far enough down to slip the block in as easily as your video shows. Your guy doesn't even have to push on the trunnion. I put on a new seal assembly do you think I have to put it lower?
@heidenburg54453 күн бұрын
Thats really cool :)
@scottjohnstone34713 күн бұрын
My keypad is one unit stuck on with a sticky adhesive. No separate keypad boards.
@joeburttschell12863 күн бұрын
What is the part number.
@joeburttschell12863 күн бұрын
My machine is the Kenmore Elite no model #
@mariotech303 күн бұрын
Half fast repair 😂
@daveevans71513 күн бұрын
This was a great video, but ditched this piece of crap washer. Have grown to absolutely despise front loaders now, especially after this. Pulled the gasket off and everything was full of mildew. The recirculating water line, drum, etc. this is a WASHING machine that uses water. This should not have to be maintained at this level. Not groaning at y’all just this mess they think is innovation. Literally just got back from Lowe’s with an old schools top loader without all the crap in it. Again, video is solid and helped me get this thing ready for haul off.
@julieschmidt77443 күн бұрын
Thank you so much for this video. I was able to remove the housing cover remove and the lint I couldn’t reach. Total time spent was roughly 30 minutes. Thanks again 👍
@rickleger35283 күн бұрын
Thank you great video it made it easier
@edgutierrez9003 күн бұрын
very favorite
@RUBYSTREETPRODUCTIONS3 күн бұрын
This video was right on point. Exact instructions. My dryer had 1 more cord that this model did not have but it was a simple step. Wish all instuctions were a clear as these instructions. THANX!!!!!!!!!!!!!!
@johnstewart72643 күн бұрын
RepairClinic, my ice maker box leaks water after dispensing into a cup. Do you have a recommendation on smart part to buy (general)?