Thank u!!

I wish I could get my hands on that planning pdf still!

Faltan medidas .

Great job!

Hey Phil why have you never emailed me back i've tried to contact you like three different times, was this just a scam???

Hey Phil why can't I ever contact you or why don't you ever get back to me?? I've wrote you like three emails, is this some kind of scam?

I don't know if this page is monitored anymore, but the link doesn't work and takes you to a spam site... I wouldn't recommend clicking it until it is fixed.

You forgot to mention how much caulking you need and you do not put it on the takeoff.

Going to attempt to move my 8x10 shed this weekend with your recommendations.. wish me luck! Will be back to record how it went 😅

Haha, LAST comment

Do you guys sell this doors?

I bought your plans a long time ago, nothing was put together right .I don't have a G&H plans or specifications? I'm building a 10x20That can't be any higher than 12 ft.I think you last messaged me to cut down the walls to make that 12 ft height. The plans are a little bit sketchy but I will figure it out Thank you. So is G&H for a 10 ft wide shed 3 ft 10 at 22 and 1/2°???

"shittin the ruff",?😂

What size pipes?

FYI, your web site link is corrupt.

Thanks so much 🎉

New to building, please help. Building a she shed office for wife 10x12 in washington state. Using 12 camo blocks with 4x4 posts using 2x6x12s on either side of the 4x4s to make beams using structural screws. The floor is then made of 2x6x10s with single 2x6x12 rim joist. Im using 2x4s for framing with 3/4 inch plywood subfloor siding with additional siding to be added and 3/4 inch plywood for the roofing. The beams go full length of the floor but the long sides are cantilevered 16 inches from the middle of 4x4 posts along the beam. The roof will be single pitch lean to style. Walls will be 7'6" on back and sides whereas approximately 9 feet on front. The shed will be finished on the inside in tiny home style fashion. And have a desk on the back side. I will have windows on the sides and a door in the middle front unless swapping it to the side is safer. Question is whether i can do this safely for my wife to work in 12 hours a day or whether i need to rebuild the walls to shorten over the beams or just focus theblive load to the center over the beams by putting the door in the middle. Most plans ive seen allow for the cantilever but when i look at residential building code the allowable floor cantilever is only the size of the floor joist. Ive built the beams floor and 3 walls already but as im new to building am getting nervous about putting the weight of those walls over the cantileverd sides. We won't have lots of things stored in the building as it will be meant for using computers and have decorations rather than storing heavy equipment and such.

l thought u would need to attach all the floor joists to the runners underneath the floor ?

Thank you very much for doing the design work and build tips for us. I started designing one and hit on the jig idea on my own. Then I saw your video and realized you already had better ideas!

Complete bs. Don't waste your time. You mention nothing about leveling or squaring or properly tying the walls together at the top: UFO made it all of the important stuff!

What about when your sheds skids run parrallell to the fence and you want to pull the shed straight out away from the fence!?

Thanks for the great videos! I bought your plans and am planning on building my shed next week. Can I make the sidewalls extend 8 inches down instead of 4 so it looks like the shed is flush with the ground? Or is there some engineering mistake I am missing?

No help if the shed is NOT on concrete

the fuck is a tuba fours?

Thank you You made it look easy, I will give it a go

Thank you! Clear explanation in voice and caption, w excellent picture examples. I can do this…

Fabulous video and much appreciated. Thank you

Really good explanation.

That's what I got going on and I'm not a novice. I have a decade of siding and window installation but these cheap shed videos need updated

thank you! Needed some ideas on the trusses

Before the top goes in caulk inside turbine to flashing and flashing to roof

I'm a little confused about the roofing sheathing. How is the overhang 12in, and it looks like the trusses are on 24 so how did you get the 8-foot board to land on a truss? Did you cut it down to seven feet?

How far to space skids for a 12’ wide building

Love this video man thank you!

Floor should of been staggered

Don't nail below the glue line. You have to cover the 2-3 nails up with the shingle that goes over that shingle. Never leave nail heads showing😮

Note: DO NOT ATTEMPT AFTER HEAVY RAIN.

I bought your plans and took on the mission of building the 16' X 32'. We not able to find help, so I built it all my self. I now only have the trusses to make, sheet and shingle the roof as well as add the wood paneling on the sides. Then, I am done. It has been an adventure.

Drill pilot holes and screw all of that in? There much better, quicker and cheaper ways of doing this. Galvanised ring shank nails will more than do the trick

That’s really easy, thank you 😂

Que bonita quedo gracias por compartir

So simple! Thank you!

Could rain water come in through the holes in the vent

If G = 12 then what is H?

Gambrel roof

I am adding on to a 10’x10’ shed and need to know the angles for a gable roof (22.5?). Thanks for your reply.

Common household items.... Errr NO its Not. Not in the UK anyway, I mean really who has Metal Piping, Jacks and Timber planks just laying arounf the house. Come on now Get real.

What size is "H" ?

thank. i was brain farting and you cleared it up. I understand everything and I like the part when you said to return anything borrowed and thank your friends… I was just wondering if you knew or know where I could get some of those? Those “friends” things that you’re talking about?

Great video! Thank you