Can you please show how to bind the controller? Changed my motor but now it works for about 30 seconds then no control.
@racecar02187221 күн бұрын
What motor did you use? Just changing a motor should not mess with the binding of your TX to the RX. Sometimes changing ESC's will need to have you recalibrate the throttle positions of your TX to the new ESC.
@leonelmolinajr224 күн бұрын
What’s the wheels & tires?
@racecar02187224 күн бұрын
The wheels are just Amazon special 1.9 beadlocks. The tires are a Power Hobby pin type tire. Great on the rocks, almost cheating tires.
@marksaxton476025 күн бұрын
Very well done video, I have the gray one and just love it. 😄
@racecar02187225 күн бұрын
Thank you very much. I really do like this crawler.
@stevenbyrd7128 күн бұрын
Looks like it’s sitting a little bit too high still.
@racecar02187227 күн бұрын
Pre Runners with the I Beam Suspension like this always have some positive or negative caster depending on how it is sitting or running, its just the nature of this type of suspension system.
@hondacivicef2ify28 күн бұрын
Nice build
@racecar02187228 күн бұрын
Thank you.
@jiveturkey36529 күн бұрын
Great video. Thanks for the info
@racecar02187228 күн бұрын
Thank you.
@bigmage25 ай бұрын
One last question for you. The winch on the bed how did you route the wires? Did you also coil them around the plastic stick on the bed like the channel 3 unit wire.
@racecar0218725 ай бұрын
Yes. I had to run a long extension on it to get it to the receiver but it is coiled around the other side of the bed.
@bigmage25 ай бұрын
Any chance you could take a picture?
@racecar0218725 ай бұрын
I would but I don't have the truck anymore.
@bigmage25 ай бұрын
Ok. Im just wiring it for someone who built it do they give you enough stuff to have that slide on both sides?
@racecar0218725 ай бұрын
Mine had the parts to do both of the little round bars that the wires are coiled around.
@bigmage25 ай бұрын
So are you just running a small 2 or 3s lipo that fits under the hood instead of in the battery box?
@racecar0218725 ай бұрын
I am running a small 3s lipo that fits in the battery box under the bed.
@bigmage25 ай бұрын
@@racecar021872 Ok thanks so much
@allaspectsrc41787 ай бұрын
Oh I want one .very cool video..u just got another sub
@RCplamodel8 ай бұрын
Thank you for introducing me to a great car! It's a great video.~~~^_^😊😊😊
@emersonpedro394410 ай бұрын
🔝🔝🔝🔝💯💯💯💯💯📷
@aviationdomination855111 ай бұрын
What remote are you using, I'm planning on getting one of these but need to know what remote is good and how many channels I would need for everything
@racecar0218725 ай бұрын
I am running a Spectrum DX5C. The 5th channel is not working correctly on mine so I could not get the Winch to work. But everything else was working with it.
@johnmiller4553 Жыл бұрын
NICE 👍. ANY WAY WE CAN GET A BETTER VIEW NEXT TIME LIKE FROM IN FRONT OF YOU SO WE CAN SEE WHATS GOIN ON BETTER 😁🤙🤙🤙🤙🤙🤙🤙🤙
@racecar02187211 ай бұрын
I am going to try mounting the camera on the cupboard in front of me as I am facing my work bench with the camera facing down so everyone can see better. Will do that on my next build. Thanks for the suggestion.