What are you using for tac solution?

Hola buen día. Excelente trabajo. Una pregunta. Que producto utilizas para posicionar el material.

after watching this video, i put my cape on,,,and believe i can ppf anything.... then i go try it, and i realize,,,, i am not Ron....but surely, watching this, opens up all the possibilities in my mind about how to do ppf.... again, thanks for the invaluable hours put here for us pheasants to learn from... Dirty

That was fun to watch! By the way, I have a Jeep and had an unusual problem with Xpel. I had a partial hood removed just a couple weeks after application due to a scratch that I caused (doh). It was done by a local expert who has added and removed PPF from my other cars before. The Xpel came off the important surfaces with no problem at all. But just under the hood, where it was wrapped, it pulled a fair amount of paint off too. Looked to me like it pulled the paint of the primer. It is not on the rolled edge that has the exposed clear coat paint, so no way at all that the repair shows. Since it is really not visible, I filled in the gaps with touchup paint, waited a few days, and they reapplied Xpel to the hood. You need to take a flashlight and really look hard under the hood to see the repair. Ever see anything like this? Not sure if I should do anything else or just wait and see. (I noticed that in some newer cars and trucks they are just priming under the hood anyway.

I appreciate these videos, I always like to watch something like this before going into a hard install. Feeling way more confident with this fender now, wish me luck!

useless! most important part not shown

Jeez! They skipped trimming. Useless!

Where can I buy this?

Very quick and simple, a lot of people spend over 1 hour per car part while you do it in a breeze. Flawless work

I have a durango with a racetrack tail light that just WILL NOT take a taillight tint without pulling back, and it's not even THAT deep of a recess. I've cleaned it thoroughly and I've used 3M 94 and even that won't have the vinyl bond to the plastic. What can I use to have the vinyl adhear to the tail light?

How much did you extend the pattern ?

I’ve personally used legend and many other films. I’m sponsored by Xpel now. Legend is barely a mid grade film. I don’t recommend this film to anybody unless you’re just practicing to start but I’d still use something better.

first time seeing your videos here! I appreciate the thoroughness!

I believe it''s impossible to not cut into the paint when trimming on the paint 100% of the time.

Another great video

Ottimo lavoro, considerando l'estrema difficoltà del cofano, molto spigoloso e concavo in molti punti. Il prodotto che spruzzi, cos'è? Acqua e sapone o un gel diluito? Complimenti ancora 💪

That's a great tip with the undiluted soap on the ridges. I'll try that out on my next hood. You've got to love the audio issues. LOL I hate it when I loose the audio on one of my recordings. You get to watch your video an extra time while you record the voiceover.

WOW, Great tips and tricks, Thanks for sharing! A lot of great stuff!

are you using gel

very nice 👍🎉

How can i contact you brother

This have been done with a 60” roll?

Hi. Thanks for sharing this. It looks so cool and will be handy if we don't have to worry about re-pressurizing every time. If you don't mind, could you tell me about the pressure out of that thing? I usually use between 80psi to 60psi(make it 80psi, and then refill when it goes down about 60psi) on my keg. Is this thing capable of making about the same pressure? Thanks in advance.

thanks for sharing. probably one of the cheaper battery powered sprayers. im in for 1

Hey man what tack solution you using? Grabs right away. Dilute ratio?

Is this a 72 inch roll

One of the best installers out here imo 👍🏽

We mostly use TPU, Now plz tell me how many drops are used for slips solution for tpu and tack solution and which one use alcohol or hot water????

Which solution is best for each film?

What Type of Slip Solutions or Tack Do You Use?

Hi sir, Excellent work, i have some questions about “ slip solution or Tack solution “

It just seems like the film obeys your commands before you even touch it. 😂 Very instructive - thank you 😊🙏

Where do you buy your torch handle

Awesome

Is that the same Mike Sanchez from down in the valley there in Texas. ? I think I've met him a couple of times at Ray Levy's, when he was with 3M, and then Sungard. Way before Madico bought them. Anyway, we're a Suntek in the white mountains of AZ. We're solid in the tinting,and while being exposed to the PPF industry never pursued it full time. Well as fare would have it were moving into PPF. What is your perhaps mix for your tack solution and what angle is on those blades your using. Enjoyed the video new subscriber. Take care.

What angle is in your carbon blades

at 20:49....i almost saw your finger sliced and on the floor....mucho cojones mang!😆😆

What is the ration of your alcohol tack solution? Great vid.

Having no luck finding this training tool. Where can this be purchased?

What’s your slip and tack mixture and ratios?

What does somthing like this typically cost? Just recently got a nee carbonfiber hood and I think I need to do this as well before mine starts fading

good

подвороты не показали как сделали

There are a lot of great helpful hints, tips, and tricks in this video. Even for a long time, installers like myself. Awesome video. 👍🏻 those air damns are always keeping it interesting. 😂

I was stressed watching this 😂

Don't stop teaching...or the world will stop learning.. I appreciate the time taken to educate us all!!❤❤ Dirty ✌️ ✌️

Very very good job!!

Thank you for your technical sharing; I have benefited greatly.

How much does it cost to do ajeep jlu?