when you are remowing ghe flywheel i think its easier to hit on the screw but first screw the nut so it lines up with the thread of the scre and just use something to lever of the side and hit with hammer good video btw
@fernandodasouza956417 күн бұрын
Un trabajo horrible les dejastes los retenes viejos, no le pusistes grasa de litio en el sigueñal, no lavastes el motor, todos los plásticos sucios!!! Compañero perfecciona antes de hacer un video por favor. No lo tomes para mal.
@eduardosousachiau954721 күн бұрын
Good day Mr. I do have a blower FS480 and don't know with candle of fuel and how can I refill..
@seanmcgrath916729 күн бұрын
how come you have two washers missing off your clutch?
@paulparkin3052Ай бұрын
Hi buddy brilliant video!! I have a fs 240 i can't get the clutch drum off the shaft , any advice would be much appreciated , thanks Paul
@tonyd6821Ай бұрын
Need help ...I bought an Husqvarna chain saw 326 the fellow who sold it to me started it and cut some wood and I bought it The day after I was using it and it went terrific for the first quarter of an hour then it didn't start anymore I though it was a carburettor problem and got one from China replaced it but didn't start . One thing that I could not understand why it so hard to start and I got a sow arm I said l may remove the cylinder off and see what is the problem ....The piston has a little scratch on the front the it has not damaged the ring ...Then I decided to test if there is any big gap in the ring and when I fitted it in the cylinder there is a millimetre gap --- plus or mine ---- the question a would like to ask you should I replace the ring and the piston ----there is no scratch in the cylinder . I forgot to mention that when I removed the plastic(?) from the cylinder and carb. that is shown 5.50---on this video---the part has 4 screws that are fitted to the cylinder ....when I removed it the gasket (?) that is glued to cylinder got a bit damaged only a little bit should by another one or use some gasket glue when put back ? ALSO for the first time I saw 2 piece of plastic inside of the cylinder probably this is the reason why the piston goes hard ??? Can be removed ? Thank you
@thomaskapetantsis4951Ай бұрын
Where’s your proper work bench, even a table is better.
@Bigmacmagicmac2 ай бұрын
Great video
@kainikander26372 ай бұрын
Minkä helvetin takia noita hommia pitää tehdä sahanpurujen seassa??
@RAMBO2BASE2 ай бұрын
Thanks. Just saved my bacon. 🤟
@user-sh2yu9ld8f3 ай бұрын
What did you use to clean the saw
@triple67583 ай бұрын
At 1:15 in, yep it'll run. I just used my gray one this past weekend. Its older than some of my coworkers and more dependable than some.
@goldfish661003 ай бұрын
excellent video saved me a lot of time and more monye after gettinrg it back for a repair shop..It came back just as bad so followed your video and did it myself...repair shop failed to notice clutch was totaly gone ....I will be paying them a visit 😠 many thanks bud👍
@nzuncovered18454 ай бұрын
I just scored a 97 CS3400 the same as yours for $10 from an op shop, looking to service it like you have. Thanks for the video
@algothica62074 ай бұрын
Hi, I am searching for the service manual (adjustments etc) for Niki carburetor. Do U know if it is available somewhere? Thanks.
@jaybillyjosh4 ай бұрын
a bit like yours did after it started
@jaybillyjosh4 ай бұрын
i have plenty of fuel
@jaybillyjosh4 ай бұрын
i have 2 questions for you if you don't mind answering, 1) i have this saw and i have cleaned all the carb and it runs but for some reason when it's warm when you press the trigger it's like it wants to cut out so several quick presses and hold it runs full on do you no why it would do this ? 2) i have new bar and chain and i tighten like most show how to but the chain keeps coming loose is the a reason why if not how do i stop this happening thanks
@jamesmilnes21944 ай бұрын
Fantastic video matey, exactly as a how to video should be done. Cheers.
@ElThomsono4 ай бұрын
I was given a 550XP that had ingested it's spark plug electrode when going full chat, thanks to this video I was able to disassemble it, and fit a replacement piston and ring, now it's back up and running again. Amazingly the bore was perfect, yet the piston was so badly shot it had lost compression (ring forced in and peened) Anyway, I'd like to thank you for putting this up, it really helped me out.
@TigerRagFishingTeam4 ай бұрын
Thanks for the help on rewinding the recoil spring on 2 series saw!
@MichaelBezzant-qx2iw4 ай бұрын
How do you remove the circlip from the inner part of the housing where the drive tube goes? 🤔 can't seem to find circlip pliers long enough 😪 😕 😫
@1982botond12 ай бұрын
A belsö biztositó gyürüt hagy lehet leszedni aszt nem mutad a videoban
@martindickens28875 ай бұрын
4..16
@tomwarner53315 ай бұрын
Thank heaps gunna do my now got the tools 🛠️, was gunna send it in to shop now not ….. thanks again
@stihlhead33385 ай бұрын
Why would you not leak test the crankcase to see why the first cylinder failed. I guess its job security when you end up putting another cylinder on because the seal's😮 leak.
@goksanmotor5 ай бұрын
My KZfaq Channel husqvarna 236 chine 5200 carburator repear
@hanslgurtner30826 ай бұрын
The tires are installed backwards.
@KJHart6 ай бұрын
I collected it like that not sure why they had them backwards
@hanslgurtner30826 ай бұрын
@@KJHart You can swap the wheels. The left to the right, and the right to the left. If the rim doesn't fit upside down, you can remove the tires and put them back on the other wheel.
@paulsouthgate89546 ай бұрын
Cheers mate.About to do mine
@gerardheijne76 ай бұрын
Thank you very much for this excellent video. I have a 026, it is an old and very good/reliable saw and I needed info about this thing for some repairs. Found it in your video, very much appreciated
@robertnln076 ай бұрын
What's cause of nose spreading I keep chain small bit slack not to tight
@imretoth23416 ай бұрын
because autotune has to be put on a computer and updated, because it doesn't work well for me, everything stutters,👍👎
@jancorish38387 ай бұрын
Ace yr english! Cheers bud.... see how it goes
@user-mn7jo8zt7b7 ай бұрын
There are jillions of these types of videos. This is one of the better ones. Mr. Hart manages to make a clear, thorough, straight-to-the point video using only his phone. Very good sir!
@salvadormonella89537 ай бұрын
I don't think these Stihl MS-170 chainsaws send enough oil to the chain. I was under the impression, and the Stihl manual alludes to this, that one tank of gas should use one tank of oil. I'm getting about 3 or more tanks of gas to one of chain oil. Whatya think?
@mountainviewcattle7 ай бұрын
Cool video. Have you got yourself a new pair of Dunlops yet? I'm looking for an orange pair to replace my green ones which are pretty worn out now, but the orange ones are difficult to find here in Canada.
@johnmasce9077 ай бұрын
nice work
@brywong937 ай бұрын
I know the recommended range is 12-16" but would I be able to run an 18" Stihl Rollomatic-E Bar on this chainsaw?
@luvegg78908 ай бұрын
Hi, I think the 'special' tool is just a piece of steel pipe that fits over the rear mounting dowel. It can be used to simply lever the eye of the spring over the dowel..
@KJHart8 ай бұрын
Thanks for that 👍 I’ve got some stainless fuel pipe about that size
@EngineVids8 ай бұрын
You dont need to remove flywheel to clean points as if you do you need to retime.
@1RCPILOT9 ай бұрын
What did you use to clean all the crud off. It looks great. Great video!!!
@marklobbett4559 ай бұрын
Nice video! What was the gasket sealer called?&where can i get some? As ive got to do my old Husky blower main seals to replace ,although Husky do a seal kit for the bottom end together with the crank seals. Many thanks
@patrickvennard8389 ай бұрын
That's really helpful I am going to put a pop up piston in my 550 MKII. The five series are much easier to work on than the three series in my opinion. Do you think that 550 just got too hot or was there an air leak that the autotune hid?
@kirtadams43910 ай бұрын
Nice job of a video. Thanks.
@ericchapman39910 ай бұрын
Tyres are on wrong
@danitiopinas485610 ай бұрын
Hi my name is Danny Thank you for uploading this video I have also a" Fs 240 C" but sins yesterday it wont start. Is it possible that the sparkplug is causing it ? Or do i need to service the machine
@hoacha111 ай бұрын
Great video. Too the point and no BS. Thanks from Canada
@dragantanackovic136011 ай бұрын
Pretego si lanac i nisi ga naoštrio!
@vasilegirigan509611 ай бұрын
TOTUȘI ARCURILE ALEA PAR CAM SLABE PĂREREA MEA PREA UȘOR SAU MONTAT👍👍👍🤝🤝🤝