Bonjour!Je pense que chacun a sa méthode pour faire le jonctionnement selon qu'il a hérité de son formateur.En général le principe reste le même et les étapes à observer dans la vulcanisation à froid et à chaud.Je fais ce travail(vulcanisation des convoyeurs à bandes)depuis 1987.
@jessiebalaoro4408 Жыл бұрын
what kind of cement will use joined rubber to drum pulley?
@user-gx3ti2wn1k Жыл бұрын
Im heaar my honymoon frind thanks God we are frinds thanks God im moslim saliut you assalam alikom Ramadan kareem Mobark Ramadan kareem my honymoon frind thanks
@lachlanmcintyre5748 Жыл бұрын
absolutely ridiculous splicing procedure.
@estebanortega295 Жыл бұрын
Empalme enfrio con cubrejuntas
@Seamonkey292 Жыл бұрын
Always overlap your lagging. Bevel the lower layer, over top layer and then grind Down.
@Seamonkey292 Жыл бұрын
Yeah, you should probably wear a respirator.
@mohanghosh7583 Жыл бұрын
can u tell me what type of adhesive use for bonding between roller and NBR based rubber compound?
@ricardovelazquez4063 Жыл бұрын
How did you get the measurement to cut it perfectly
@chainspending63434 ай бұрын
Times the diameter of the pipe x pie Example: pipe od 250mm x 3.14 Answer 785mm
@FarhanKhan-mu6qz Жыл бұрын
Nice
@carlostrajano5456 Жыл бұрын
Faltou os epis ne kkkk
@edwintadile Жыл бұрын
good day sir do you have rubber liner for hire ? I am from the Philippines and have a experience for rubber liner , I am Currently working in mining industry in the Philippines
@chandrasekharkunala8943 Жыл бұрын
What is the rubber used for hot joint of steep angle belt Rubber material name pls
@bigikediesel2 жыл бұрын
Do you have instructional videos for joining sidewall? Do you ship to the States?
@Justvulc2 жыл бұрын
There are currently no instructions for sidewall. Subscribe to our channel so you don't miss it when it comes out! We ship to the USA, contact us for details justplatform.com/en/contacts.html
@anilshukla67772 жыл бұрын
Good what did you apply for covering the rubber does it need vaccination ?
@edwintadile2 жыл бұрын
what is the title of your job?
@derekleblanc5712 жыл бұрын
Good work!
@derekleblanc5712 жыл бұрын
Why wouldn't you just do a long pre-bevel one end then stitch your lagging up the bevel? Only time I do a but to but edge is strip lagging.
@Justvulc2 жыл бұрын
We do it with proven technology!
@derekleblanc5712 жыл бұрын
Doesn't matter so long as it works. but if your not perfect with your mesurements and calculations you might have a gap or be forced to try to shrink the lagging wich will often cause a section with air bubble /( unbonded lagging to pulley) Easier and safer to ride a few inches of rubber over a gradual bevel then cut and buff the extra. But if you can line it but to put perfectly then awesome good job! Do you seal the but seam ? Of so what do you use?
@alex86902 Жыл бұрын
@@derekleblanc571 Hi Derek, We use a similar method to do our drums. We lay the rubber to a 15mm overlap from our measurement to allow for mistakes, once glued and stuck up to the last edge we will take a mark and trim the edge to within a 2-3mm overlap using a small shim on the underside to prevent premature sticking, we then lay the rubber in and stitch away any bubbles while the glue is tacky. We do this method to allow for multi directional travel and if it is in a harsh environment will seal it with a 2 part rubber mixture. I can say from our experience over the last 10 years failure due to the butt join of the lagging has not once been an issue. I do enjoy seeing other methods so of you have any tips id be glad to hear them.
@derekleblanc571 Жыл бұрын
@@alex86902 interesting technique kind of the best of both worlds. I like it. And that 2 part rubber mixture is probably the tire repair compound wich works awesome. Thankyou for the share.
@haronwaruru48582 жыл бұрын
Which glue is that
@Justvulc2 жыл бұрын
This is a cold vulcanizing adhesive TRS 2002 NEW justplatform.com/en/catalog/chemical-products/trs2002.html
@haronwaruru48582 жыл бұрын
The glue
@AjitKumar-nr7ot2 жыл бұрын
Steel code belt ka splicing dikhaye.
@Justvulc2 жыл бұрын
We don't have that video right now. Subscribe to our channel and be the first to know if such a video appears!
@marvinsoriano56112 жыл бұрын
how to calculate diamond grooves in roll 90 inches rubber face,16 inches diameter
@eduardomachado7788 Жыл бұрын
Medir o diâmetro do rolo e multiplicar por 3.14
@sanjaykolhe76682 жыл бұрын
Belt chhilkar palay ko khichne wale tool ka Nam Kya hai.
@user-ze5in8gx2h2 жыл бұрын
Полный бред
@elijahgichohi78343 жыл бұрын
Why use a sledgehammer to kill a house fly. Why the the winch . Contact me by my email for an easier and faster way of splicing . [email protected]
@fabiopassos85253 жыл бұрын
Qual o contato fone
@Justvulc3 жыл бұрын
justplatform.com/es/contacts.html
@indianproductionplant7823 жыл бұрын
That is cold solution
@sadrianagrest41203 жыл бұрын
Perfect
@bayronsotoherrera42513 жыл бұрын
Creo que para el Forrado del tambor hay otra opción que es solapado que también queda ien
@MrFernandoBedoya Жыл бұрын
cómo es?
@bayronsotoherrera4251 Жыл бұрын
Montando una punta unos 2 o 3 centímetros encima de la otra, pero antes hay que hacer un desbaste a la primera punta los centímetros a montar
@MrFernandoBedoya Жыл бұрын
@@bayronsotoherrera4251 Gracias. Tiene sentido.
@PraveenKumar-wg1sv3 жыл бұрын
More details (Cutting rubber size Electric or pneumatic Blade type)