Hi I followed same steps. When short it, can see red light on the charger. But, as soon as I disconnect, it is turning back to green. How long do I have to hold it for? Tried holding it for 2 mins

WORKED BUT IT TOOK A FEW MINUTES TO BUILD UP A CHARGE TO ACTIVATE CHARGING ON IT'S ON, BUT IT WORKED! ORAISE YAHWEH!!!!!!!!

If the charger still does not change to red and battery does not what could the problem still be

Thansk you broo it is goood 😮😮😮 very very good my bro

Be easier. To tripod the CAMERA ! Instead of DUFUSING...

Gracias hermano me sirvió mi sobrino se había puesto triste por que ya no funcionaba pero con tu vídeo pude arreglarlo

I have this issue , right out the box 😭.

Good idea

Thank you daddy

I think I'm just going to replace all those cells with high-capacity cells, that way I get more than twelve miles out of it I can double it and maybe twenty-four more

in my case it became red for 5 minutes then again green. The hoverboard now has 2 bars so at least it powers up but the charger is still giving me a green light so I suppose it's not charging anything...

How long do I hold it for

I did a variation I just held a bridge wire between the earth into the board and the battery minus for a while and held it there for a few minutes then when took off the bridge it kept charging must have been just enough to fool the system

you are a clever, clever dude, thank you worked great!

I did this and I revived a dead 36v battery pack. Now my question is the battery on B- and the positive terminal on the xt60 connector shows 40volts but when I test the voltage at the connector it reads 25 volts. I think something is wrong with the BMS and I have an extra one as someone gave me two hover boards with dead batteries for free. Any ideas?

A massive thank you mate for this explanation and tutorial on how to solve this issue, I tried it 1st time the bypass I didn't have to do for long as I new battery had charge moments later my battery started to charge and work again, a massive thank you again

I tried to by passed but charger light still green. I bought new charger but still green while charge. Does it mean battery died ? I tested battery it 22.1v . Any ideas about that? Thank.

My brand new hoverboard run time is around 25 minutes then it cut off power of board. At full charge it was around 41.5 V and after 25 minutes the battery voltage was only 37.8 V for cut off. Why is the voltage still so high and already there was a cut off the power? At wat voltage should the board switch off? Any suggestions?

Are u n asheboro

But the charger will be cut☹️💔

Thank you for this helpful video. I did what you described us to do, and it worked a treat. 😀👍

Very good explanation and it's working perfectly. Thank you very much Sir. I didn't cut the charger wire. I used 2 small wires and connected them directly in the plug charger and bypassed the battery for 2 min and inputed again as original. The charger came back on red charge. I didn't use the hoverboard since 1 year. I charged just 2 times so the hoverboard stayed new. But I forgot to recharge again before storing. So I suggest to anyone to never let the battery low a long time. Insure to recharge your battery before store during winter.

What do you do if you have 2 wire from battery

Thanks very good explanation i will try tomorrow since I don't have extra wires around :S

my battery is different,i cant bypass the wire any help?

do i need to slice into my power cord or can i use just one side of the plug (the hot side)

Question, if I just re-solder the negative cable on the PCB board over to the bypass location would that ensure that the problem never happens again?

Thank you alot it work very well

My charger doesn't get red light how i fixed it and my hoverboard also not charging

YOUR ARE A KING... THANK YOU..I ONLY HAD TO DO THE BYPASS CHARGING FOR FIVE MINUTES AND PLUGGED THE BATTERY BACK IN AND ITS CHARGING WITH OUT THE BYPASS NOW THANK YOU SO MUCH!!!

thanks bro this trick realybworks

At 4:51 did you say 2 hours or 12 hours? I am very confused.

How long does it take for charger light to go red once the wire is connected to the b- terminal ?

Thank you very much! It's fix my battery. I tried to short before but it was unseccesful because I didn't keep if longer. When I follow your video my battery first blink red and after about 1 min the light was read. Now charging without any problem. To short I use a wire and conected - to the + like you when charger was connected

Please tell me

How i battry by i have big hoverboard 10 inch tyre

Sir mere 10 inch tyre vala hoverboard hai mai kon se battry buy kru

super safed the day