Hi there! I use Dayton PA 460, Dayton PA 200, Dayton horn and a GHXamp 1,75 inch commpression tweeter.

Hi, the Eminence coaxials are in a closed box. The subs have a slot reflex port around the back.

They are great, crisp and accurate. I had them crossed over at 1700 Hz.

I had them professionally resprayed as there was a severe discoloration in the grey paint and a large scratch on one of the speakers.

200 Hz and 1700 Hz

Yes indeed. Kind of sorry I sold them some years back. I built something even louder now. 😄

Thanks man! 😉

@@Vouwfiets9 i’m designing 10 inch coaxial studio monitors. for mixing and mastering music. I’m not sure why no one gets it yet. except Tannoy. check out the Tannnoy Gold 8. I want that design in a 10 inch with more power Tannoy Gold 15A is sick too

@@johnviera3884 I actually built these as poor mans Tannoys. 😄 Better casing, just not the nice Tannoy finish. Good luck on our monitor design. 😎

Thanks! Reflex ports are tuned to 30 Hz, most 18 inches will manage that.

Thanks man! Looking too fancy will never be a poroblem for me. Finishing of speakers is not my strong point. 🙂

Thanks a lot! Yes they go plenty loud. 🙂Bass is pretty nice too, the simple Canon camera doesn't pick that up really.

I sold these a long time ago. I remember being not very impressed. Okay speakers but nothing special. Not sure I tried swapping left and right. Maybe that's why. 🙂

Oh wow, that was a long time ago. 😀 I think it was 200Hz and 5 kHz, to get the most out of the Mark Audio.

No it was just a simple box. I think I didn't even put bracing in it. :-)

Hi! Tough one, it was 10 years ago. 🙂 What I can remember is the incredible spaciousness and detailed sound. Bass was completely lacking however so need a subwoofer for most music. Watch out for loose wires with second hand Magnepans.

Crown XLI 1500

Out of the box, no contest. The Lintons are far, far superior. The CV I had to room EQ, they sounded slightly bland and muffled right out of the box. They can go crazy loud though and with REQ were very, very capable speakers. I prefer the Lintons, they don't need anything, they just make music.

@@Vouwfiets9 thank you sir...

Thanks man! Very happy with these loudspeakers.

Yes, I bought these for 40 euro's. Really surprisingly good speakers. Lots of fun. Not available anymore, I guess these are 15+ years old.

Hi! Gain was at 60 dB and Inpedance at 1 kOhm. The latter was a bit much (fierce highs) and now I use a Rega Fono MC set at 400 Ohm.

I really had to look because it was some time ago. 🙂On bass it was a Yamaha P3500S, midrange a Behringer A500 and the highs were done by a Samson Servo 170. I've got a comparible speaker set up now, but slightly bigger. 🙂

Thanks! It's not that impressive. 🙂 It's a Rotel RC03 pre amp and Hypex UcD 400 mono blocks. And an Behringer DEQ2496 for room correction.

It's not an analoque filter. Crossover frequencies are set by a DBX 234XS (high-mid-low) and level correction by means of a Behringer DEQ 2496 DSP.

The behringer is not there to contribute, it is an essential part of the system. With the DBX I decide the crossover frequencies and the gain of mid/high/low. With the Behringer I control the frequency spectrum, as an equalizer, and as room correction. It helps me get a flat frequency. In a 'normal´ set up the Behringer definitely helps to get better sound in room.

Hi! I agree with you, the entire table feels firm and bulletproof, except the tonearm lift which is flimsy. I sold it in the end and got an SL1200 again, a Mk6 this time. It felt like coming home. Before that I bought a new SL1500C, but the same thing there, very flimsy and in my case faulty arm lift. I run the SL1200 with a Denon DL103R and also a Pro-Ject Phono Box S2. Very nice combo. :-)

@@Vouwfiets9 I have learned to work with the somewhat weak arm lift. Nothing is worse than a stylus that takes a sidestep towards the outer platter rim after being dropped. So I carefully lower it each time just to be sure. I really like everything else about this deck. And the only other deck I might consider would be a belt-drive like a Rega Planar 3 or a Fluance RT-85. I am a sucker for these beautiful acrylic platters lol

@@svenschwingel8632 😄✌

Anywhere out of the world by Dead Can Dance

Behringer DEQ 2496 is the DSP and a DBX 234XS for the crossover.

Oei, lang geleden dat ik deze had. Ik dacht iets van 25 cm breed en 30 cm diep. Hoogte ongveer 105 cm denk ik. Geweldige speakers, als je ze kan vinden.

Hypex UcD 400 monoblocks

Hi! It was an active system, with Crown XLS 2000 for bass, and Samson Servo amps formid and high.

@@Vouwfiets9 Thanks for your answer. And which sounds better to you: the CROWN XLS or the YAMAHA P3500S ??? THANK YOU