edgin rn

Why do you even need that.

The quick releas rol is to remove the steering wheel to have room to get in and out from a competition car. They dont last long. After every race or event( drift, rally)they need to be changed for safety.

You bought a knock off product and expect it to be up to standard. Come off it.

What laptop did you use in order to get it working properly?

high quality production

lool this is jokes

Only bought this so my integra wont get stolen 🥲 now yall making me regret it

"Steering wheel goes out the window, you die." Hate when that happends... 🤷🏼‍♂

Looks familiar 🤔 Nice setup tho!

What BOV is this

what do you expect? get a proper nrg, works bell, nardi etc hub. get what u pay for

Thats the EXACT wheel I am about to buy...

Are these knockoffs?

then maybe. just maybe. dont cheap out by buying on ebay?? go to the real deal and not buy fake stuff

Could we have a tutorial?

My sparco quick release isn't like that one.

Just got done making mine off of your measurements. Fit nice and snug. APPRECIATE IT!

it legit says oparco

great video

lol i like the ride up and the shirt.. lol

I would call this a hot air intake. Scooping up the headers heat.

Thanks man

That’s why you buy nrg and not something cheap that you think will do good because it won’t

Hi, I have some of these photo interrupters but can't make any of them turn off. Mine are marked with the standard led symbol on one side and a raised dot on the opposite corner , so impossible to mix up polarity. A 10K resistor works great but nothing I've tried, shuts off the beam. Remove the power, and the led goes off after it uses residual voltage (maybe a capacitor ?) Could be a different type of interrupter - don't have any spec sheets .

The ebay link goes to AFM adapter that says 600dollars :0 Did they change the price up Shkreli style or what?!? LOL

Thank you! Ben wanting to see a video on this for my Eunos

what's the name of control panel hinge? Where can I buy it?

Thanks so much dude !

That AFM needs to be rotated 90 degrees, it should be horizontal to allow the gate to swing freely. What ever gains, if any your loosing with it in that position.

Happened exactly the same on my simracing hub, few months and the problems started

Yo is that the moneypit miata?

良い子はNRG買おう

using this cheap fake quickrelease back in 2012..got same problem..loose ball bearing..steering will shake..try NRG original quickrelease..better and safe

in other words, water is wet. buying a fucking ebay part for the most critical part of the car

Link!?

Thanks

Any link to get the kit???

How did you change the Miata chime please I’ve been wanting to know but I can’t find it anywhere

Im french and thanks you for your tuto

Did you notice any power increase

Hey I’m thinking of doing this setup with a different wheel and hub. I have the short hub and 2.0 quick release but I’m still deciding what wheel I want. You run the boss hub which is a little bit longer I’m running the short hub so I can run a deeper dish wheel. My set up should be around the same length as your so I was wondering if the steering felt too close to your face?

Can it still be done with Android???👉👈

How do I do this!?!?!

Wow I can't wait to blow up my engine!

ok that is NOT stock, there's a nice exhaust rattle mod done to it. sounds like a honda civic lmao the catback sounds MUCH better I'd say y'all mostly fixed that horrendous exhaust rattle

Thank you sir, my 1990 Canadian Miata now has a beautiful wooden NRG wheel, quick release, and hub. All with a working horn!

We need the tutorial :c

This looks like the moneypit miata lol

This tutorial helped me realize that I had been using the wrong card this entire time, also that I probably have a fake or a clone since it has a 2021 label, but the site says that it stopped production in 2013 :^) but the card still works so I don't care. Thanks