Hey man so i went on the looser side 11in on exhaust and 9in on intake. Now i notice a little ticking is that normal since i went on the loose spec? First time doing my valve adjustment btw.

You are not even using the coolant bleeder screw?!? why do you think they put it there? for decoration?

Check out the S2000 Prop Rod Secret videos, bro.

Excellente, muchas gracias!!

Awesome tutorial really appreciated it

not a lof of oil varnish in that motor. how many miles?

Don’t know if you have the solution but I got my depo headlights tapped to my indicators and when I go to use my signals they don’t work so I flip the light switch to off and they blink with the angle eyes and the indicator.

Are the angel eyes blinding at night?

I wish you showed the location for the slave cylinder better

Hey how has the 75w-90 held up ?? Really curious because I’m gona be using this fluid soon thanks

what's the green liquid in the engine?

what year is your s2000? I have a 2007 and my fuse box is a lot closer to the firewall and is getting in the way of removing the cylinder.

Phenomenal DIY Vid!!!! Thank you so much for all the details you provided so thoroughly.

Teach me more

Another moron who pulls the orginal cooling system off the car that had 150k miles on it and calls it "trash." Then puts a bunch of aftermarket TRASH that only lasts 2 years and then blames bmw...absolutely amazing

Your E36 is si clean bro this is insane keep it up

Very clear explanation ... thanks!

What’s the part number for the OEM weatherstripping

Great video. Just did this to my Alpine White/Modena convertible. I kind of did the opposite though. Used a Stewart water pump and an OE radiator. I like the Mishimoto radiator and if my car were a manual coupe, then yeah, I would definitely go this route. But for an automatic convertible, that radiator would just be overkill. Stewart water pumps are just better than all the others. Both our E46s have them and the cars just run cooler than before. The only other one I would use is the BMW OEM pump because now they have a metal impeller instead of that cheapie plastic crap. With all the other aftermarket pumps, you get what you pay for. Just spend the extra $100 and get the pump that will last for the rest of the car's life because the cooling system is the Achilles heel of this motor.

👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍👍

Where can I get the thread chaser from ?

no Sealnt?

Yo so how do you turn the halos on and off?

What length studs were those?

detailed video, well done

Because they're aftermarket lights you're going to get a "Low Beam Failure" message on your OBC every time you turn your lights off. You can install signal interuptors (cheap) or ignore the message (even cheaper).

Can’t find these headlights anywhere

so what ado you do with the bike and red wire that’s connected together on the back of the headlight, do you keep them connected?

Is the thermostat housing leaking ? You didn’t put sealant in it

Still have it? Wanna sell?

Good stuff fam… what’s the tool to install the wheel studs not sure what’s it called man

Did you notice less fuel economy when they needed to be adjusted?

Nice car drive safe😎

love the video, super helpful. I was wondering why you decided to not delete the fan clutch while you were down there? I know those have a tendency to explode under high rpms and can put a hole through the radiator. You can install an electric fan or put a lower temp aux fan switch with lower temp thermostat on and it runs just the same.

lol man I envy you nobly for the car. I think this is the coolest e36 I've ever seen. And I've seen a lot of them.

Doing the same thing soon 💪

What wheels do you have on your car? I also appreciate the videos you do for maintenance hopefully you’ll be able to do more. Also hope this channel grows. God bless🙏!!

Looks great man, nice job. I’m installing the Bayson R AP2 lip as soon as it comes back from paint.

DO YOU HAVE AN EMAIL ADDRESS SIR?

where should coolant level be in expansion tank once the temp gauge is at ideal position?

What thickness 3m tape did you use?

Wat size engine is in your e36 1318ti

Nice information yu offer..its very detailed

Have a 95 m3 i just got and need to swap out everything, any recommendations on a good kit?

Did the 3M tape and the couple of screws on the sides hold up until now? I usually see these using bolts from the inside of the bumper after drilling holes along the front.

Will air in the system cause to to over heat fairly quick?

How do I fined these head lights ?

I got the same lights on my dakar only i did a bixenon retrofit with d2s. Gonna install them in a couple of weeks

Where did you get the CR lip? Did it.come painted?