Thank you so much. Excellent teaching technique! I am waiting for my headlights to arrive and will refer back to your video next week.

Jamie, thanks for sharing this video! the funny thing I've just ordered a new latch from an online spare parts store and it appears to be shipped from Texas to me in Saudi Arabia 😂, probably if your ML waited 4 years you'll get the spare part sooner 😂. I just want to fix it ASAP as it drained my main battery overnight, also I've bought a new battery but I'm not going to install it until i make sure everything will be good to go!

Mine still doesn’t work

Thanks

panasonic switch abj362860 is direct replacement $ 7.17 from digikey

Thanks to your video, I fixed my fuel cap warning light! Thank you!!

Nice job! Thanks for sharing.

Did you used a smoke machine to verify the leak?

So this is the second video I've seen where they show you the tool they were supposed to have used in the tensioning kit but because they didnt realize what it was they thought they had to create a make shift tool. I just want to save everybody a headache and 30 minutes first attach the 19 mm socket to the tension bolt then grab the small bar out of your tensioning bar kit (this bar is known as the tensioner attachment used to create angles with the tensioning bar) attach the small bar to the socket then attach the main tension bar in your tensioning bar kit to the bar attachment ( the smaller bar in your kit) and socket already applied to the tensioning Bolt that is how to correctly use the TENSIONING BAR ATTACHMENT and the purpose it was created for.

Hola, excelente trabajo! Tengo un ML350 año 2012 y tiene el mismo sonido cuando pasa por un desnivel, cambie amortiguadores y bieletas de suspensión, mejoro un poco pero ahora se siente mayor el ruido como gomas chichando. Las bieletas de suspensión también tiene izquiera y derecha? Como lo identifico?

Can you please tell me which way you turn to take off the last nut at the top please I’m having a hard time I watch the video over and over but this this is not turning

Thank you so much for this video this helped Alot 🙏🏽

Thanks for posting part numbers, it helped a lot 👍

Do u know where is the abs relay on a 2001 f-250 V10 gas located at ?i cant find it or located in the truck is the abs relay part 19283 relay duralast

Sounds like a skill issue

Thank you ✅️✔️👍🏼

Also be careful with the oil cooler outlet pipe, I dinged mine up and had to replace it. Pretty sure it's made out of aluminum also.

I've had that same thermostat you replaced the old one with break on me twice now. Don't recommend it at all. Also you don't have to take off the whole panel on the bottom to drain the coolant. I've been able to do it without even having to jack my car up lol.

The other two comments are tripping. The door is held in by clips after the two screws. If you can’t figure out that and disconnecting the electrical connectors/door latch cables, maybe you should take your car to a shop. Don’t bite the hand that feeds you [information] 😂😂😂

torque head bolts 26ft lbs and then additional 180 degrees, can anyone confirm? and do you do the 180 degrees all in one turn or in multiple stages? any help is appreciated

please... where & which fuse will deactivate motorized latch if pulled?

Great job do u know how to do the timing chain in this car

I drilled the hole in steering column & spray wd40. Then the fuse & wire harness method. Battery at 12.35-12.4. Alternator charging. Crank over at 10.4-11.5 sometimes. Then now no crank & now I’m lost.

Thank you so much. Im going to have to perform this job myself.. god bless!! 🙏

Thanks - your video was the most helpful I found on the University of KZfaq.

Dude! You ROCK! The Nylon Strap to feed the Wiring was Genius!! Thanks so much for posting this. You're a Life Saver Brutta'!! 😎🤙

Thanks for sharing

Very late comment but this also just happend to me ! If you happend to have any laying around, a simple bolt with a nut will also work for this too & than you will never have to worry about it again 👍🏽

Thanks buddy got into fender gotta replace 😅

What is this rubber plug part called? Mine crumbled and fell out so I am trying to find a replacement for it. For the car engineers...why did they even h=make this hole behind the brake.

Don’t you have to reprogram the abs module ?

I've had one like this for 15 year now with the exception being the one I have has the upper connection different in that it has a partial circle hinged on both sides that goes around where the spring is and then has hooks that are adjustable with wingnuts that hook over the coil spring on each side. Just don't use anymore because they come as assemblies with new springs and mounts now. Was looking to redesign into pipe bender. Can see how my design would be safer in that it hold onto the spring.

Did you have to bleed any lines to the ABS Module or to each individual wheel?

First time i did my own alternator. $207.99 remanufactured . Three hours. Thank you for your video.

Thank you.

Hi there sir I watched you and you did a great job can you help me from where to buy the micro switch for Honda Odyssey 2010 for sliding doors I thank you very much, David.

Well made video.

Hey so I recently replaced my thermostat housing assembly shown in the video with a new ac Delco one but now my car seems to cool down every times it’s in drive but it will heat up when In idle

Can get mine to compress enough?

Ok I have problem None start on my car I'm making parking what's good The No Starter again

What about completing the starting system check: Starter, Solenoid, Starter Relay, Ground, Key fab, etc.. Checking the entire starting system.

What can happen if i let abs on and no fix. On this trucks

Thank you. My 2006 L322 has a similar problem. Every once in a while, I turn the key and....nothing. measured 11.9V. No go. Connected my booster battery and started immediately. Battery is less than 1 year old. Why is the voltage sometimes dropped below 12V? Crazy.

well done...

Question, does the left gate have two power struts or just uses one power strut on the right side?

I’m going to try replacing the headlight assembly on my 03 Lexus ES 300 today. I’m not sure how confident I am. I got pulled over last night. Showed the officer the new assembly that was in my trunk. He let me off with a warning.

Ola saludos mi troca ford f150 97 cuándo freno el pedal se va asta abajo y se le enciende la luz del abs me podrías decir qué será

I just figured this out the hard way, you are right to point these out! Thank you

went to picapart. crawled into ml500 thru rearside doors. used screwdriver in hole under lower 2inch popout over latch. pried latch open, pushed door up, very heavy, have prop or 2x4 to hold door open. pop out panel on edge, then door cover panel loose , eureka, now m30 torx screws. mercades 500 has fancy studs to put in floor rails in holes to secure luggage, nice alum. system not in ml320.

I have a curious, can we remove the 2zz-ge part by part? Without the hold engine out of carbine? And can we renistall back part by part too?