This is fine for the PTO driven mower. What about the ATV mower? It's NOT the same.
@novatractor5592Ай бұрын
Same theory, adjust the engine base height and angle, to set the two pulleys aligned.
@danielbrown86025 ай бұрын
Hope they're not paying that guy by the hour.
@ToddP11 ай бұрын
Title is misleading. That was how to change a cross bearing, not a yoke on a pto shaft. Horrible music too.
@user-mm8mi5oo8b Жыл бұрын
Sa kusjton nje si kjo po per te thy dhe dega
@Lorec1855 Жыл бұрын
I bought one of these from Novatractor, that is supposed to take up to 4 inch pieces of wood. It will only chip up to 2 1/2 inch diameter limbs without choking. I've had nothing but trouble with it. It wouldn't start right after putting it together after delivery. After mutiple phone calls to Novatractor and redirects from them to repair places, I was told that the warranty won't cover anything having to do with fuel and Novatractor was not helpful. I was sent links to videos on you youtube explaining how to start the machine. It had been shipped with a gunked up carburator and cost me to repair a brand new machine. The tires have no tubes, so if they go flat, you need to remove them to line them up to fill them. In addition, the tires need to be deflated to be mounted on the chipper. The lip overhang prevents the tires from being mounted while up to pressure. There are other design flaws that make this machine a chore to use. The battery, fuel tank, everything is licated under the chute. The chute is understandably heavy. But it is bolted in place on one side and hinged on the other. If you take the bolts off to open the chute so you are enable to get to the motor, thechut must be propped up or it will cause the housing to bend from its own weight by the hinged side of the chute. I am very, very disappointed in this machine.
@novatractor5592 Жыл бұрын
@greenj1m Жыл бұрын
Helpful. Thanks
@jellevankapel20692 жыл бұрын
in midden en aan zijkant stel moer ..beter.
@benscoles50853 жыл бұрын
I bought one of these chippers couple weeks ago, got delivered on June 1, put it together, greased it up and chipped about 3 wheel borrow's full in about 10 mins, pretty impressive, if the limbs were green, it would have been faster yet, , first time chipping, I had a little trouble getting the feed right, if you have too long a piece, you have to hold up the other end a bit, so it will self feed, the only problem I saw, was that the grease zerk on the front side bearing was not accessable through the pto cover, , I had to take the bolts out one at a time and move the lock washer to the front of the pto cover so it was moved back just about 1/8 inch, so the grease gun nozzle would click on the zerk, other than that it was full out go get em chipper fun.
@arthursmith86193 жыл бұрын
the music? What the hell. I just turned it off. Useless
@DidblG3 жыл бұрын
If that doesn't sell me into buying one of these critters, I don't know what will....
@pengchen50483 жыл бұрын
So B A D
@sideskraft3 жыл бұрын
PTO speed must be close to 1000 rpm based on the speed the branches are sucked in how fast the chips are flying.
@kathymitchell52023 жыл бұрын
How do you remove a jammed piece of wood?
@novatractor55923 жыл бұрын
shut down the engine, open the output chute and clean them out
@mrtree13685 жыл бұрын
Can u make a video showing how far it can shoot the chips we need to know if it'll make it to the back of our trucks it seems the shoots end was pointed down so it's hard to know from the video
@novatractor55925 жыл бұрын
Nice question, I will make this video next week, to show how far it can shoot.