Just a blank as far as I'm aware.

it's a relief valve in case you overpressurize the regulator so you don't damage components or the regulator itself

I chose this regulator for that reason over others since I'm not constantly monitoring the pressure when playing on the field

Excuses my COD lingo lol

If you buy it new - Yes. Balystik regulators need a specific tool, others like Redline, Polarstar or Wolverine tend to use a hex key (allen key).

Costa VIP

It's coming soon!

@@AngryBullAirsoft ill wait 😁😁

SLS

If it's a tight fit on th einner so it doesn't wobble then yes.

airtac.me

Easiest way to reduce consumption is to reduce the weight of the moving parts, less weight to shift means less gas used shifting it. Lightweight bolt would be an easy swap out. I used the 5KU standard lightweight bolt and it made the pistol snappier, lighter, less recoil (not that there's a lot) and I got really good efficiency.

I tried this and it caused me some feeding issues. Maybe my oring was too wide (1mm) but it instantly caused my Article to feed 3 BB's then stop, mag out, bb's dropped out, mag in and it fed 3. Removed O-ring and it sorted itself.

Wild guess would be a bit of dirt in the mechanism, usually when a reg leaks a rebuild, new seals and grease with Gun-Sav fixes them.

@@AngryBullAirsoft alr, thanks👍

For the 5KU frames, I've found they work significantly better with a CowCow disconnector.

Thanks for the comment - The AAP can be a fiddly platform and is difficult to get right. The groups and forums are usually full of people with feeding issues because of unbalanced spring setups. My honest advice would be go for a Capa. They are a slight bit more initially but are far easier to build and work on.

​@@AngryBullAirsoftThanks for the advice. I'm reading this after I already have it in the mail and on its way to me, so, I'll get good at fiddling I guess. I like tinkering, just new to tinkering with airsoft, but I'll pick it up quick. Have you changed your mind or have any insight on parts since you put this out? I'm also not seeing anything called a knocker lock anywhere, is there another name that part might go by? Thanks again for the info and for the straight forward and we'll produced videos. I'm excited to make my way through your collection.

Context is your friend. I wasn't referring to the playing pressures. I am aware that there are some ULP setups that I have seen used in the US. Not that US airsofters use low pressure. As I am aware that my content is viewed from the US I wanted to make that caveat to acknowledge there are other high pressure systems out there. I appreciate you getting involved but you've grabbed the wrong end of the stick.

@AngryBullAirsoft fam i got crap on my hand....I apologize

Agreed. My preference is not to run hammer pads for the reason you've given.

Absolutely!

That's a Magpul K2, you have to drill it to get the line through but Wolverine do a really good video tellng you how to. Really nice fit for me as it is more vertical than stock.

Will it stand the test of time though?

@@AngryBullAirsoft tbf as airsofters we don't need too much of an excuse to spend money on things do we?? 😄

@@tk2097 I didn’t want to sound eliteist, MTWs are £600+ starting - £20 on a body pin is a drop in that ocean 😂

천만에요 <3

UK Light License is the one we went for. The license itself goes down in one persons name but you can name a "group" on the application and then essentially you can distribute between you. There is no upper limit on people *I think*, we had around 10-12 when we did this so it worked out very cheap per person.

@@AngryBullAirsoft Thanks I'll certainly look into this in near future as more of the lads see getting non pmr compliant radios.

The only other thing I can think to advise would be to run them on narrow channels, wide seems the better option but you don't need loads of spectrum for what we do and quality won't be noticable. Narrow means you get better range for your output power and you're less likely to pick up noise as well.

Glad it helped 😎

They grow on you. This is the 3rd M4 pistol I have owned, first 2 were home brews. This just feels right!

It has the Spartan board already so yes you can set dwell, rof, fire mode 👍

Heretic Labs Article 1 Airsoft CQB Gameplay at Skirmish Kirkby in Ashfield kzfaq.info/get/bejne/o8ylm9Nj2Lqbgok.html

@@AngryBullAirsoft savage

Feed issues are hard to diagnose, could be the mags, could be your adapter (or rifle) nozzle speed? So many variables. Pre load them correctly though and they’re normally very strong performers.

Appreciate the feedback - it is directed as more an overview of what parts I found fitted the golden eagle, not an intention of “this is the best build”.

Video published 3 years ago dude. Likely bought parts from Hi Capa Hub.

Mostly 3d printed, files are not available as these are parts given to me from a manufacturer.

No problem glad it helped 👍

Not on this one. You can get WE models that are switchable and TM did the Extreme45 that had full auto. You can also get a disconnector from LACC that will make a capa go full auto.

Thank you - I got mine from 18Airsoft but I have ordered a fair bit from 6mm in the past. Both are quite reputable. I'm happy with it so far.

Thank you 🙏 Was a mighty sprint as well man. Worked well having us going deep into enemy territory 😎

Thank you 🙏 and Agreed!

Kind of. I’ve never had anything perform like an mtw though.

@@AngryBullAirsoft its like they build most things correctly and saved the time we spend on different things like nozzle alignment, airseal and stuffs. those who dont fine-tune their stuffs may get one for convenience.

This ^^^ It's a game of honour. If you think you've been shot - you call it.

😂🤣😂🤣

Cheers dude 🙏 Was a brilliant night - one of the better ones I’ve had. Looking forward to the next one 💪

Drum mags are available 👍

Yes it can 🤓

@@AngryBullAirsoft amazing, can't wait to get my parts then!! Thanks mate

A1 really shone. Give me a shout when you do 👍

Super5ives!!!