its basicly 1120 degree ?

What happened to the compact table saw?

I would recommend not gluing your panel in. Look into using space balls. They are rubber balls that allows the panel to float which allows expansion and contraction.

I have a juice groove and I like it. Cutting chicken or oranges and it doesn't run onto the counter.

Like your presentation style and like the end result. Greetings from the other side of the pond. 🏴󠁧󠁢󠁷󠁬󠁳󠁿

Bravo you have mastered the cutting board. I was just saying yesterday I really wish there was another cutting board video on KZfaq.

Incra 5000 sled is just $350 compared to the combo $315 do you think a incra 5000 is possible on a jobsite saw?

Cut your boards to the length you need. Hot glue a piece of 2x4 cut to be +4inches longer on each end to both sides. 2x4 pieces get the snip, boards are fine. I usually rip my 2x4 into thirds or half’s depending on the thickness of the wood to be protected. Hope this helps.

2:59 Wouldn't it be better to place the concave edge against the level, as the two ends would make contact, rather than the convex edge which has a greater potential to shift during the cut? I use a tracksaw as I don't have a tablesaw, however what you are doing looks wrong to me...

I do not do juice grooves in my boards..

Another option for filling in those holes (aside from CA and epoxy) would be hot melt/glue sticks. I've seen a good number of KZfaqrs and real-life maker friends use this depending on the application.

juice grooves are annoying but not if your cutting meat. I groove one side and say one side for meat one side for veggies

Incra Miter Express Value Pack - amzn.to/3UTDLNx

Thanks very much for a very explicit video. Thanks also for mentioning the bit sizes, as others seem to leave this information out of their video.

Excellent job thank you very much

No tightening of lock nut when satisfied with alignment, same as manual but the sawstop video suggests tightening the locknut, otherwise won’t it just vibrate out of alignment again? Thank you for your video!

Waxing aluminum is unnecessary. If you wax anything you still need to let it haze and then buff it smooth.

I curious why you used solid wood for a cabinet thats going in to a bathroom? Are you not worried about swelling? Also, you said it was going between a toilet and shower? Why not make the cabinet out or vennered mdf or plywood and use the solid to make a frame for the cabinet? This seems like you either lost a bunch of money, broke even or charged way to much for something that will wventually crack and swell from the co stand moisture of being in a bathroom

DeWalt Planer - amzn.to/3y0NQkl Wixey Digital Planer Gauge - amzn.to/4bmXjAP

thanks for taking the time to make this video , this is the best video i have found on how to do this

Well I also bought a Sawstop from Lee Valley 2 weeks ago but haven’t opened it yet since it’s still sitting in my kitchen 😂. Had a Dewalt last year and came close to losing a finger…..I bought this for the safety brake on it. Thanks for the advice ❤❤❤

For your router direction, use the right hand rule. point your thumb in the direction that the bit is in, and the direction of the curl of your fingers is the direction that the router is spinning. You cut against that direction. Works regardless of whether the router is in a table or freehand. I've added that circle cutting jig to my Lee Valley wish list, for next time I make an order. My last circle cutting attempt, used a homemade lazy-susan like jig, and my router table, but it got out of control, spinning my circle like a record player -- very scary! Your setup looks much safer (although I could probably do something similar just by drilling a hole in my giant oversized router plate, which I'd made to avoid the router dipping into a cavity that I was hollowing out.)

I just received my sawstop cts and can’t wait to set it up. Also subscribed thanks for the video ❤

Is that the MRP23EVS router? Just curious because I want that router but they say it won't work in a lift.

Looks like a nice sled. Kinda pricey but nice.

I was wondering, if you routed a rebate on the inside of the top, and the outside of the bottom so they nested. would you get into the dado for the bottom, or would the sides need to be thicker?

I have been carpenter for 20 years and biscuit joiner does same thing as domino for a tenth of the price

No splitter/riving knife?

Interesting and nicely explained. Some gear that I’ve considered, so this gave me more food for thought, especially that right-side support. You mentioned your concern about longer pieces; might be interesting to hear how that works out. Thanks.

They look great. Check whether you’re using that handheld router in the right direction. May be the camera but looked like you may have been going in the wrong direction.

Good video, @4:50 all I could see is your hoodie strings getting caught on something in the future. I have garage hoodies that have NO strings for that one reason. Cheers!

Looks like the blade you have on that saw is a full kerf forest blade? Those jobsite saws usually come with thin kerf blades to make up for the lack of power- might have just been asking too much from the saw.

Nearly everyone puts two coats of monocoat (ironically, according to YT; personally never used it) That looked like a THICK cut to put through a small jobsite saw. Were you using a ripping blade?

spending 1200 on a dedicated joinery tool is not 1 year woodworking activities.... there you go, there is your controversial comment. that thing is INSANELY OVERPRICED and constantly shoved down "normal" peoples throats by YT influencers that get shit for free.

I'm just guessing here, but I wonder if there was some strange grain pattern within the wood that caused it to bind on the table saw as you were pushing it through. The wood looks nice finished but I would like to have seen them installed to appreciate how it all looks in final form.

Wow I found the tso parallel guides super easy to set up super accurate what I did find trying other track saw brands was tracks were inconsistent and the toe in on others track saws not adjustable festool was a lot more consistent from track to track and the saw toe adjustment was a huge deal good luck

Nice video. I like the TSO parallel guides, but the markings are hard to hit bang on. I cut a spacer stick out of 1 x 2 material and place it between the back edge of the track and the TSO stops. This sets them at exactly the same spacing. Parallel cuts, without the fuss!

Great video😊 After a few years of hobbyist woodworking I have also invested in a Domino and and a good track saw. These are among my favourite tools that makes woodworking easier and more fun. Good luck with the channel! Greetings from Sweden

Hello from Vancouver Island 🏝️

I have the TSO track things on Black Friday sales. Warner weather will let me get out and use them. I’m making many cabinets and I think that is where they’re the most useful. I hope. I want the WoodPeckers stainless Delve squares but am happy with other measuring tools for now. Makita track saw because, like you, invested in them. More corded Makita than cordless though and the track saw is corded. Definitely getting the JessEm router lift when I build a cabinet. I understand it also fits in the SawStop cast iron table. Another possibility just to get a fully cast iron top and avoid any laminate or formika particleboard table.

Agree with you about the parallel guides. I have the woodpeckers, the TSO, and the Festool parallel guide systems. The Festool parallel guide system is dead on accurate and so easy to use. Repeatability is perfect. It is also the best made for durability. The disadvantage with the Festool system is it has a limited range of max at about 25 inches or 650 mm. Otherwise, the Festool system is repeatably accurate and well made. The TSO provides various (3) one-piece lengths parallel guides, but the stops are finicky as you pointed out. And the woodpecker parallel guides are a series of parallel pieces which must be attached but the attachments must be rechecked throughout the cutting process to make certain that they don't come apart, which they do. When I must cut a series of pieces 25 inches or 650 mm and under, I use Festool. If they had the cutting range of woodpeckers or TSO, I would not have the other two systems.

Sorry man, but after one year of woodworking very few people have a domino and a Milwaukee tracksaw and a woodpecker ruler.. i didn't watch the last two because the title of the video is misleading.

Solid content pal.. New sub earned.

I have the same parallel guides and what I have found works best is to reference off your clean edge and make two marks at each end of the board to your measurement. Then set your track splinter guard against those marks. Then I simply set the parallel guides to this reference. For repeatable cuts you now are referencing a standard size you verified with the tape measure and not the scales on the parallel guides. Which are not the easiest to set.

Great job they turned out great

Hey Ryan, I may have a second and third reason to build one. While I grew up with access to my dad's workshop with all the milling and fine woodworking equipment one could ask for, and I work in the trade myself, I never developed the desire to really immerse myself in the world of woodworking until recently, as I approach 60. I've been looking at Lee Valley's $179 CAD drillpress table (in Toronto) but keep coming to the conclusion that I'm going to build it instead. My primary reason for wanting to build it myself is the advantage of developing and refining my knowledge and skills on tools I am less practiced with through the process. I also just like bringing my own concepts to life. For me, these more than pay for the time. It is an investment of time that pays dividends by adding something to what I am made of and adding a little of me tangibly into the world. Or I could just have a drill press table...lol. Cheers, Paul.

Excellent work..! I have been using Watco butcher block oil on the live edge trays I build. Seems durable with three coats. I sand with 600g between coats.

My zero clearance insert was warped and the replacement they sent me doesn't seem flat either. Gonna make my own eventually

those would’ve looked sharp with opposing color splines. They did turn out pretty sharp though.

Would of been nice to show what you can actually can fit in the trays such as plate of food with cutlery and a glass of juice. Apart from that nice build.