cash on delivery not available

bhai tu zameen pe ajaaaa practical karo

practical alag hota hai

is size bobin main fit nahi ayega swg

Sir apne jo bobin select kia hai 4no 4" Isme 7no swg 28tern nahi jayega 17no se 290tern aap is bobin ata dijiyega

बहुत दिनों से तलाश थी इस तरह के वीडियो की , आपका आभार ........! मेरे पास RO में लगने वाली सोलेनोइड वाल्व 24 वोल्ट की है उसकी coil जल गयी है उस coil को 48 वोल्ट की बनानी है इसकी जानकारी देने का कष्ट करें

Sir hmm kise transformer ko dak ke kaise andaja maximum kitne volt ,amp de sakta h sir plz reply

Very good Need to know calculation for ferrite toroidal transformer

6kva toroidal transformer ka kia requirements ha I mean 48V dc to 230v 50 hz

Sir mere pass 2 pis core hai dono same size hai to Dono core ko pareler kar ke transformer bana sakte hai kya

Length calculation is wrong..... Because when turn layer by layer then the perimeter will be increased then this calculated length will be short. In transformer turn is more important than length

Можно себе представить чем дышит это мастер.

Gjbbb

make sure you catch all part of bottom side of circuit board.

Power handling capacity of a toroidal transformer=100× WA. W= window area = π×ID×height and A= core crossectional area= π×{ (OD-ID) /2}×height . And TPV= 10/A.

OD, ID and height all are measured in inches

These firmulas are derived for 50 hz freauency only

OD is the outer diameter, ID is the inner diameter.

No, not at all. Because every transformer has core loss, copper loss hota hai. To isliye primary power secondary power se jyada hona jaruri hai. Aur core ki window area aur crossectional area product se hin transformer ki power handling capacity pata chalta hai. Fir jitna swg wire select kar rahe ho aur jitna turn dalogi is ki width bhi window ki width se 20% kum hona chahiye.

Pehla formula wrong hai. Transformer ki power handling capacity iska window area aur crossectional area ki product se nikala jata hai.

Solding iron price

Hath se kabtak lapete ga danda dalke subha se sham ho jayega lapette lapette

Bak was hae jo purana hae wahi best hae itni mahgi masin koe nahi le payga toraidol wainding ke liye

Bak was hae jo purana hae wahi best hae itni mahgi masin koe nahi le payga toraidol wainding ke liye

Ei sabse best hae meri mano to

Waending kaese karenge toraidol ki jalne ke bad

Так вот как китацы штампуют платы для нас 🤯

Good video bhai

Number dijiye

Sir kitane kilograms I or E core chahiye ye keise pata karenge?

Будни недомастера?😂

not perfect

Anisha Chowdhury and May and June and will

bro. you have formula for EI core to calculate core power?

What type of soldering is that?

Wow good information

How to find Messer amps(current)in transformer

Super thanks 🙏🙏🙏🙏🙏

И как при таком нагреве не плавится пластик на разъёме?

Sir good morning, mere pass toroidal transfoemer core hai size H-3. 8,W-4 CM otherwise D1-15 CM, D2-7 cm, H- 3.8cm. To TPV Or Watts nikal ke digiye ga. Ismai 1 kg copper wire tha jo ki 13 no or 8 no ki thi. Ac stabilizer 5 kva 165v to 280v ka

Vai ata ki jinis

I’m using the 42 for my centre tap transformers with good results.

Core Weight Calculation Chart Chahie

OSFT Soldering/Desoldering Iron Tweezers For SMD Soldering and Desoldering Iron Buy link amzn.to/3VpLCEm

I Don't smoke.

Sir 1100VA me bhi yahi calculation use hogi ya formula change hongy ...

Soldering by hand would hv been faster

How to check toroidal transformer if primary winding is correctly done as i am getting humming sound and capacitor and diode is getting hot also.

Very nice, sir ji detail video banayo,, thanks

Go onnn🎉