Model Makers

Пікірлер

@theunknownatheist3815 15 күн бұрын

This is exactly what I did to restore a set of Ludwig Vistalite drums. it works great they came out looking nearly new.

@nnlomeli 16 күн бұрын

GREAT video!!!! Thank you!!! Had no idea. CAn you please tell me where can I get this solvent welding? Thank you again!!

@stevejennings899 18 күн бұрын

Amuses me that people over that side call everything 'sandpaper' when the abrasive is anything but 'sand'. Useful vid though. Not sure if novus is available in UK?

@deny9540 22 күн бұрын

Iam worker acrylic India

@aljundating1574 27 күн бұрын

Thank you.

@LolaPotter Ай бұрын

I have used half of the heavy and light scratch remover WITH an orbital polisher. This product is the most ineffective product I’ve ever purchased. ZERO impact!!! I have pictures.

@LolaPotter Ай бұрын

I hope the Nobs people pay you well. I followed your instruction to a T and ruined the item - it had a large scratch now it’s damaged beyond use.

@Bigbandfan99 Ай бұрын

Where can you buy methylene chloride and the needle applicator

@CanadianCommunistt 2 ай бұрын

Thanks

@canuckle7shucks 2 ай бұрын

Methylene Chloride, also known as Rez-n-bond. Used this for 37 plus years in the sign business. You can make a thick glue with this by adding scrap acrylic pieces to a gallon and letting it sit for a few weeks

@canuckle7shucks 2 ай бұрын

I’ve been flame polishing acrylic in the sign business for 37 yrs. I sanded down to about 600 grit. We used straight acetylene with one or two passes along the edges to produce a transparent glass finish. Sometimes with a rag and Methylene Chloride, (which is the main ingredient for gluing acrylic), you can shine up edges with that.

@aljundating1574 27 күн бұрын

Thank you from the Philippines.

@lolslim690 3 ай бұрын

Hello! I was wanting to know I 3d print mostly in ABS, and I sometimes need to put pieces together normally I use ABS glue (mixture of abs filament and acetone) or just straight acetone, would weld-on 3 be a better option than the two I already use when joining piece together or does it depend on how it will be handled/used?

@1978garfield 4 ай бұрын

You used to be able to get methylene chloride at any hardware store. Stupid EPA banned it because over the course of 40 years a dozen people didn't follow the directions about ventilation and died. About half of those were stripping paint from bathtubs, a use that the label told you not to do.

@terrable_makes 4 ай бұрын

Thanks for the info! I am trying to use this technique but I am not seeing an instant bond, it is not "sticking" until it's sat there for a while. Any advice on why? they are laser cut pieces, so all I can think of is maybe i need to lightly sand the edges.

@iAnasazi 4 ай бұрын

Have you figured it out?

@Dog3D 4 ай бұрын

Great video, no fat and straight to the point

@jenniferbyrne4567 4 ай бұрын

Great video thank you.

@kopineo7270 5 ай бұрын

Hello I don’t know if you are still seeing this but I’m trying this method on my anime acrylic stand that has a scratch in it and it removed the scratch but the sandpaper scratches are gone what should I do?

@LolaPotter Ай бұрын

Do not use this product. This is another you tube video fantasy!

@davidfreitas3992 5 ай бұрын

Does this work on saw cut edges? I caught in the middle of the video on the manufacturer's website that they recommend ips weld on 16 acrylic cement instead if not a purely flat finish which your video seems to show?

@burakuslu3661 5 ай бұрын

I am trying to make aquarium by plexiglass. Can i use that solvent? Is it waterproof?

@nickloss2377 25 күн бұрын

yes. this is the only way to do it if you're building your own aquarium. my brother has built a ton of custom aquariums using this method.. there are a few KZfaq videos that show the technique.. once bonded, I think he used a bead of silicone where he had bonded two pieces of acrylic together.. like caulking.

@deny9540 6 ай бұрын

My tekink is best. Iam job me

@deny9540 6 ай бұрын

Sir acrelic kar pientar

@emildimofte6538 6 ай бұрын

👏👍🥂👏✌️✨🐬🎼🙏🙏🙏🌿🙏🙏👍👍👍👍👍✨🐬✨🎼✨🎼🙏🙏

@user-ot3ht9er8h 6 ай бұрын

Does this solvent create a water tight seal?

@firestorm117 6 ай бұрын

Just a note, your mic was WAY too close to your neck. You kept pressing into it and distorting the audio when you leaned your head down.

@54egg 6 ай бұрын

Nice video. I have a hairline crack in a hard to find pool filter fitting that was suggested to try capillary action solvent bonding "repair". Where do you source VC-1 or E-Z Fix #309?

@nmc5h8MIZ 7 ай бұрын

Is the bond improved if you can somehow apply pressure to the joint? I'm guessing since the liquid is so thin that an unsmooth surface can also mean a poor bond?

@nickloss2377 25 күн бұрын

no. pressure is not going to make it melt faster.. it's not a glue. I wouldn't even consider it a bond. the two pieces of plastic are being melted together by the solvent. applying pressure might inadvertently prevent the solvent from spreading as far as it could. that would result in only part of the acrylic coming in contact with the solvent. I've built aquariums using this method and the trick is to ensure both pieces of acrylic are flat, and free of any imperfections from cutting. sanding with a very fine grit is essential to ensure the pieces of plastic lay flat on one another..

@jerrycrafts5301 8 ай бұрын

Where can you buy methylene chloride you use in the video?

@mikef522 8 ай бұрын

worked flawlessly! made holes right on edge of acrylic effortlessly. I used some water with coarse side of Gordon combination sharpening stone from harbor freight to flatten the cutting edge. Took 1-2min to flatten each edge (my bit had 2 edges, was the standard titanium 118 degree bits from harbor freight). You just make the cutting edge of the tip flat instead of sharp. He said parallel to shank, which is incorrect. parallel to the cutting edge. Flatten the sharp cutting side of the tip that makes the angle of the drill bit, opposite the flute. Cheers!

@marybracamonte8265 8 ай бұрын

Very nice

@lastcent5140 8 ай бұрын

worth metioning dichloromethane is carcinogenic. Can also be found in paint stripper in australia. Thanks

@joshuaritter791 8 ай бұрын

Very helpful video. Thanks!

@cooltroop2 9 ай бұрын

Would this work on an acrylic watch face?

@goodairin 9 ай бұрын

Excellent video - shows technique and informative about materials. Thank you!

@sudheergodgeri 9 ай бұрын

Great info and technique - thanks I needed just this to make a small PC HDD cage using acrylic - without drilling/making holes

@user-iq9mr5kb4c 9 ай бұрын

염화메틸렌과 다른 첨가물을 혼합해서 쓰나요?? 접착면에 기포가 많이 생깁니다

@DJ_Switzer 9 ай бұрын

Would be nice if you mention your tools when you mention your materials.

@postullio8775 9 ай бұрын

Where do you buy your methylene chloride?

@MiscellaneousMichelle 9 ай бұрын

Awesome video

@LolaPotter Ай бұрын

Yes considering he did that with a straight face.

@delana9398 9 ай бұрын

Does anyone know it I can use these products on a black acylic shower pan???

@delana9398 9 ай бұрын

Can you use this method on a black acrylic shower pan??

@bluberryswisha 9 ай бұрын

Have an acrylic panel for my PC and I'm gonna try to make it look new again, scratches aren't deep at all I can't wait to see it looking spotless again thanks

@faizeefaiz2142 18 күн бұрын

What your results on pc?

@Henry14arsenal2007 10 ай бұрын

Will this work on monitor screens?

@LolaPotter Ай бұрын

This works on NOTHING.

@lavague7648 10 ай бұрын

It was hard to find methylene chloride in Greece. This solvent is highly regulated in Europe. I am impressed that works so well on acrylic. I tested also acetone as other videos suggested but it does not work. Many congratulations for this educative video.

@rohansupremacy4001 10 ай бұрын

AWOOGA 😍

@gaboaaa23 11 ай бұрын

just what i was expecting

@shantigeary4212 11 ай бұрын

Or you can buy a drill bit that’s used for soft material like a 90° drill bit… 118° is made for hard metals

@jeffeastman8238 11 ай бұрын

what gauge needle are you using for your glue applicator? Thanks, Jeff

@randallsemrau6911 11 ай бұрын

How do you whip that dispensing bottle around without dropping MC all over? I end up with blotchy plastic every time. Is the nozzle too large? What size nozzle is on that one?

@cherrycherian6429 Жыл бұрын

Exceptionally useful video for all who have acrylic aquariums.

@goldenegg4517 Жыл бұрын

Watching the video, just after I chipped mine 😭.

Ең жақсы KZfaq

Пікірлер