ADRIAN

Пікірлер

@christophervargasschebesta3752 20 күн бұрын

Nice video how long did it take you? both parts

@huistv2005 27 күн бұрын

Really inspiring! I am going to try this also. Thx.

@pedroespinal3593 Ай бұрын

How can I make the aluminum molded part?

@salihkayis Ай бұрын

Can you make transparent polycarbonate? How transparent and clear will the image be?

@AdrianDIY Ай бұрын

I don't know, I never tried that.

@RelaxingMusic-rq6zt 3 ай бұрын

Kia ap log airgun ki pellets (chary) wali dai bna sakty ho

@nc.92 6 ай бұрын

Thanks bro. I'm stealing this idea.

@stevezevallos3735 8 ай бұрын

Can you share or do you sell the g-code for the wooden bullet? I would like to give this a try….

@ArcAiN6 9 ай бұрын

are there design files available so i can make one?

@AdrianDIY 9 ай бұрын

Sorry, no

@spehropefhany 11 ай бұрын

Nice. Machining some screwdriver slots in one mold half for prying wouldn't hurt.

@JS-.- Жыл бұрын

Where could I buy one of these bullets?

@1HourBule Жыл бұрын

I would like to buy this machine to do this at different sizes, keys, etc

@AdrianDIY Жыл бұрын

I build this machine for myself. You can buy or build one.

@1HourBule Жыл бұрын

How do I create or buy this machine?

@cnc-me4rm Жыл бұрын

You are cutting with water?

@AdrianDIY Жыл бұрын

Yes, rain collected water.

@Dreddip Жыл бұрын

@@AdrianDIY 🤦‍♂

@Nikolas_A Жыл бұрын

What about rust???

@AdrianDIY Жыл бұрын

I cleaned the vice after use and oiled.

@skunkjobb Жыл бұрын

Exactly what I will do. I thought about annealing it but I want to keep the hardness. Also thought about EDM or chemical etching but that wouldn't be very exact. This seems simple enough and precise.

@AdrianDIY Жыл бұрын

Tell us, how did it go.

@marcelocaetano635 Жыл бұрын

very good!

@AdrianDIY Жыл бұрын

Thanks.

@muebledurable8270 Жыл бұрын

Hi Adrian, your 5 axis cnc is incredible, what do you use to control the 5 axes, arduino with ramps or tb6600 and how do you configure them?

@AdrianDIY Жыл бұрын

PlanetCNC controller.

@maurondndramirezm744 Жыл бұрын

¿Y como queda inyectado?

@AdrianDIY Жыл бұрын

kzfaq.info/get/bejne/lciqaLKGlZ-um30.html

@pabloperez9268 Жыл бұрын

Men I hope your channel grows quivkly you're extremely talented

@AdrianDIY Жыл бұрын

Thanks.

@engdenis3326 Жыл бұрын

Hello Adrian. I'm from Brazil and I really loved this video. Is it possible for you to show a little more of your machine? I also use Solidworks. Thank you very much... congratulations.

@AdrianDIY Жыл бұрын

Thanks. If you watch through my other videos, there are some where you can see more of my cnc. Here is one of them kzfaq.info/get/bejne/lciqaLKGlZ-um30.html

@RecyclingAsAHobby Жыл бұрын

Amazing ! What kind of tool you used ? How you fixed the bottle to the holder ?

@AdrianDIY Жыл бұрын

Simple engraving tool. The bottle is holded on the 4 jaws chuck protected with masking tape. The spring-loaded tool holder is homemade.

@titaninventor Жыл бұрын

good luck👍

@AdrianDIY Жыл бұрын

Thanks.

@baptistmonteiro5972 Жыл бұрын

Very well done

@AdrianDIY Жыл бұрын

Thanks.

@baptistmonteiro5972 Жыл бұрын

Where can I learn to make aluminium mold

@AdrianDIY Жыл бұрын

You will find a lot of information online, just search.

@baptistmonteiro5972 Жыл бұрын

What are the topics that i can search

@AdrianDIY Жыл бұрын

That depends on what CAD software you plan to use to make the mold.

@CATANOVA Жыл бұрын

Those die grinder bits do wear quickly.

@AdrianDIY Жыл бұрын

Indeed.

@CATANOVA Жыл бұрын

@@AdrianDIY Have you tried the YT shorts yet?

@AdrianDIY Жыл бұрын

Not really.

@CATANOVA Жыл бұрын

@@AdrianDIY KZfaq Shorts are where you pick up most of your subscriptions from. All you got to do is make a decent video in portrait rather than the usual landscape. Make sure the video is under 60 seconds and then upload as usual. When you upload, YT will automatically grade it as a Short so nothing further for you to do. If the video is decent you should get a couple of thousand views and perhaps a couple of subscribers. Keep repeating to build on the numbers.

@AdrianDIY Жыл бұрын

Maybe, but I don't think I will.

@dandordai9190 Жыл бұрын

Awesome

@AdrianDIY Жыл бұрын

👍

@ugurerdogan2389 Жыл бұрын

😂😂😂

@AdrianDIY Жыл бұрын

😉

@baptistmonteiro5972 Жыл бұрын

Wow that's cool ❤ which cnc company is this

@AdrianDIY Жыл бұрын

Thanks. Is home-made CNC, my own design.

@tinayoga8844 Жыл бұрын

I think you did a good job. As far as it being tight for the bolt head. What I would do is to cut a few groves into the bolt head with a hacksaw, to give some channels for the plastic to grip onto the head. Then I would heat the bolt head hot enough so it can partially melt the plastic. Then press the head into the plastic. I would try this on the first print to see how it goes before trying it on the better part. I had tried to do some plastic molding. I did not have a mold machine. The mold I made was for a dome for a light sensor. It was 50mm in diameter. I had virgin ground plastic that I placed in the mold then heated the mold in a toaster oven. When hot enough I pulled it out and put it on a drill press table and I used the chuck to press down on the top of the mold. I had a couple of holes in the mold that allowed the excess plastic to flow out. I held it until it was cool enough (but still hot) to remove the part. Pulling it off before it cooled completely allowed for easier extraction. I worked as an electronic designer and this was what I did to get some prototype parts. I'm retired now so I'm only working on hobby projects.

@AdrianDIY Жыл бұрын

Thanks. I've made another video where I added ejector pins kzfaq.info/get/bejne/eLd6iqt7trnTnpc.html

@J87513 Жыл бұрын

Good job!

@AdrianDIY Жыл бұрын

Thanks.

@J87513 Жыл бұрын

What cnc machine did you use?

@AdrianDIY Жыл бұрын

Homemade.

@Gabriela-ge7bx 10 ай бұрын

@@AdrianDIY can u build for me

@AdrianDIY 10 ай бұрын

@@Gabriela-ge7bx to build what?

@Gabriela-ge7bx 10 ай бұрын

@@AdrianDIY aluminum mould

@AdrianDIY 10 ай бұрын

@@Gabriela-ge7bx send me an email.

@AdrianDIY Жыл бұрын

Here is the recipe: 6 eggs (the first one must have 2 yolks, otherwise I don't guarantee that it will come out the same) 6 spoons of sugar, 6 spoons of flour, salt, baking powder, powdered sugar DIY CNC - spindle speed 1200 RPM 😂

@CATANOVA Жыл бұрын

👌

@AdrianDIY Жыл бұрын

🤘

@CATANOVA Жыл бұрын

👍

@AdrianDIY Жыл бұрын

Thanx

@CATANOVA Жыл бұрын

How does the air get out? Looks cool.

@AdrianDIY Жыл бұрын

Thanx, in this video is the first thing I'll explain kzfaq.info/get/bejne/lciqaLKGlZ-um30.html

@Arjan-swets Жыл бұрын

what software do you use?

@AdrianDIY Жыл бұрын

Solidworks with CamWorks.

@aphexnet Жыл бұрын

Wow, what software do you use for do it?

@AdrianDIY Жыл бұрын

Designed in Solidworks and for CAM I use CamWorks.

@ugurerdogan2389 Жыл бұрын

👏🏻👏🏻👏🏻

@AdrianDIY Жыл бұрын

Thanks again.

@ugurerdogan2389 Жыл бұрын

👏🏻👏🏻👏🏻

@AdrianDIY Жыл бұрын

Thanks.

@Basteleddie Жыл бұрын

Hammergeil!

@AdrianDIY Жыл бұрын

Thanks.

@AwesomeActsOfRandom Жыл бұрын

crazy the way things happen. Never in my life had I needed to make wooden door handles. now that I need to I got to thinking maybe i could use my cnc to carve them, and I was thnking how cool it would be to have a 4th axis on mine to do it. And then your video pops up! Very cool, it turned out great!

@AdrianDIY Жыл бұрын

Thanks, you can do it in 3 axis too, it's just more convenient to have a 4th axis.

@mmctuner Жыл бұрын

Hola Adrián! Podrás hacer un video mostrando la máquina entera? Saludos y felicitaciones por tu trabajo.

@AdrianDIY Жыл бұрын

Thanks, I'm considering it, but I'm not sure.

@zeldalink6278 Жыл бұрын

Where is part two? It’s almost a year now :((

@AdrianDIY Жыл бұрын

Here it is kzfaq.info/get/bejne/j9KCiM9-uN3HeIU.html

@davidharper4289 Жыл бұрын

You are my savior. I have to drill 2 x 6mm S/S ball bearings with a 4mm hole (I have just ordered from our friends in China) to make the top release activator/bar in a Vertical Mill (bitch).....$84 plus postage to buy one.......your vid helped me sort out how to go about it!! Cool, Thanks, Cheers, Davo from Aus.

@AdrianDIY Жыл бұрын

How did it go?

@mavigogun Жыл бұрын

What is the workable volume of your machine?

@AdrianDIY Жыл бұрын

Axis travel is X=540mm, Y=850mm and Z=280mm.

@mavigogun Жыл бұрын

@@AdrianDIY That's fantastic! Many such machines of similar proportion feature a much more limited Z axis. What do you reckon the largest stock dimension you can address completely? Do you have a build log documenting the construction of your machine?

@AdrianDIY Жыл бұрын

Stock dimensions are same as travel for X and Y, for Z is dependent how deep is machining features on material, if is down to table stock is less than half of travel. I don't have a build log, was made years ago on the fly...

@susurrosjoe6817 2 жыл бұрын

Beatyfull!! Which CAM do you use for it?

@AdrianDIY Жыл бұрын

Camworks.

@robrathwell3319 2 жыл бұрын

This type of operation is much like turning. Because your cutting point is moving away from the center of rotation, your C axis rotation should be slowing. It looked to be staying steady so your actual feed rate (the rate at which the material was being fed into the tool was increasing greatly. Good attempt though!

@AdrianDIY Жыл бұрын

Indeed, but for wood is not critical.

@thanhnhanhuynhnguyen3652 2 жыл бұрын

I firmly believe you deserve more viewers!

@AdrianDIY Жыл бұрын

I appreciate that!

@jeanlucbergier7728 2 жыл бұрын

great job ! I'm impressed. what firmware do you use on the CNC ? GRBL ? MACH 3 ? And the second mill you use ? I can't see the shape because it's rotating :-)

@pilotpug 2 жыл бұрын

Nice. Any idea to like automate 100 of these once with perhaps some minor remains that would need to be hand cut?

@772777777777777 2 жыл бұрын

What controller are you using

@AdrianDIY 2 жыл бұрын

I do not recommend it to anyone so I prefer not to say it publicly. Edit: Things have changed over time, and now it is a better controller, so it is PlanetCNC.

Ең жақсы KZfaq

Пікірлер