Sam's Garage

Пікірлер

@Detodounpoco-xb2zo 6 күн бұрын

Is this kit the same for a j18a? Thanks!

@SamsGarage_ 5 күн бұрын

Yes it should be

@johnmathew3389 18 күн бұрын

Leftvside cv axile

@fishhuntadventure 29 күн бұрын

16:43 too many pieces and tools for my tastes. One thing is the TWO locating screws(?!) for the adjustable sleeve, for example. And the adjustable wrench for wheel center locating bolts - needs to be studs or welded nuts with tapered lug bolts like a trailer or bmw.

@MsKeileigh Ай бұрын

Just the spacers would have been sufficient. Grinding the guides was really a waist of time. In fact grinding the big flat side of the spacer that rides the arm just makes it looser and then causes you to need a thicker spacer but nice video anyways

@SamsGarage_ Ай бұрын

They were worn flat, so I tried to grind them back to original form with a ridge in the middle which would catch better on the metal part. But yes, the spacers are probably enough to make it work.

@MsKeileigh Ай бұрын

Yes Sam I suppose we are both right I guess it just depends on who's doing the repair if they are qualified to attempt to grind it or they could get their selves in trouble real quick

@zemoney954 Ай бұрын

❤Thanks for sharing Sir … remember if both tensioner have gaskets?

@SamsGarage_ Ай бұрын

No gasket on the lower tensioner!

@tylerhardie3343 3 ай бұрын

Cheers lad this has given me the confidence to do mine

@ghp0518 3 ай бұрын

What were the symptoms that lead you to change it?

@pawepablo2504 4 ай бұрын

write the number of the new part

@miguel97yahoo 5 ай бұрын

I hit the beat breaker with a mallet against the tire couple times when in the middle of pulling down and it works every time.

@raymondhellberg3600 5 ай бұрын

Excellent! I'm about to do the same job. Nice reference and with most of the torque specs too - thanks!

@mcrobbo69 Ай бұрын

i couldn,t hear anything

@charlieibkiss4068 5 ай бұрын

Question for you Sam I'm doing this job on my Chevy tracker the only problem is, I have that the cam shaft chain has slack at the top even with the tensioner on. Do you think my tensioner is broken? Even though I bought it brand new.

@SamsGarage_ 5 ай бұрын

There is some slack when the engine is not running since it operates by oil pressure, so this could be normal.

@charlieibkiss4068 5 ай бұрын

@@SamsGarage_ how much slack is some slack? Is there a way were I can send you a picture of the slack? I just don’t want to mess it up if it’s too much slack thank you Sam.

@SamsGarage_ 5 ай бұрын

@@charlieibkiss4068 At 10:42 in the video you can see the slack, that's the old chain of course but I'd say it's about the same in the new. There is no "ratchet" in the upper tensioner so it doesn't do much when no oil pressure is present

@RobertWilson-nq9ks 2 ай бұрын

@@SamsGarage_Re

@smoke05s 6 ай бұрын

I find that if I slip the tire back so that the arm of the bead breaker is going straight down at minimum or just slightly outward toward the rim. That keeps it from kicking out like that. Also using the hole closest to the changer will give you more leverage but sometimes the width of the tire will not allow using it. No matter which hole you use its the arm angle that keeps it from kicking out. Love that duckbill mod. That's a must have to eliminate scratching.

@garyp1930 7 ай бұрын

nice !!

@peterrivney552 7 ай бұрын

Try some dish soap and water it makes it a lot easier to dismount and mount tires. Myself I'd do some modifications to that bead breaker like mounting an old scissors jack to stand use an impact or reversible drill save your back and shoulders on breaking the bead...

@vicinvesta8349 8 ай бұрын

At Walmart, mounting tires cost like $11 per wheel. And you do it once in 5-6 years..... So here is that.

@alans.4658 5 ай бұрын

$11.00 and 5-6 hours lol

@sofijagallo8921 8 ай бұрын

Nice upgrade on the tire too! 👌

@weltreisenderd231 8 ай бұрын

Показал и рассказал отлично, но в конце я ждал всё таки куда заливать масло. И не маловажно замена славного и заливного болта. 👍

@blubu68 8 ай бұрын

why not put the bar inside the cross tube it would give you more leverage

@piecetoyou8285 8 ай бұрын

weld a flat strip of metal to your bar this will help the bar you use to spin the the duck bill around , to keep the bar more stable on the round vertical piece , Round pipe on round pipe is a pain and welding a flat strip prevents the bar you hold from slipping,

@elijahmcgaugh8219 10 ай бұрын

The one that you just took off the rim

@elijahmcgaugh8219 10 ай бұрын

Hey i need a used 225/70r16 inch tire

@sstjacques 10 ай бұрын

Have center cone but too small for Mercedes rims, works with others kike ford and audi.

@DonaldChesley 10 ай бұрын

looks like the bead breaker is on reversed

@goldwingconepatterns2565 10 ай бұрын

Adding to the bead breaking part I watched someone else struggle with the bead breaking until he moved the tire out from the centre a few inches. It caused the nose of the bead breaker to drive itself in towards the rim as the user pushes downward on the bar. The bar containing the bead breaker nose moves out at an angel by quite a bit. I haven't purchase or done it myself yet. Soap and water may add to the ease. See what you think.

@erkanuyar6672 10 ай бұрын

Perfekt gemacht:)

@dyardsale5475 11 ай бұрын

You sound like Peter Finn.

@rickj.2638 11 ай бұрын

My man you might want to really anchor the manual tire changer to the concrete to stop it from moving I thought you would get better results what breaking the beads

@SamsGarage_ 11 ай бұрын

This was the first time using it, it helps a lot to spray some lube when breaking the bead, which I didn't do here! Also I was trying not to let it slide against the rim to avoid damaging it...

@AIRMANBEAR Жыл бұрын

I BOLT MY MACHINE TO A HEAVY PALLET AND THEN STAND ON IT

@inthelandofmilkandhoney457 Жыл бұрын

Relocate your Bead Breaker tool to the first hole closest to the tire machine. It will go in against the rim and won’t slip out.

@stonebarrow5165 Жыл бұрын

Aboustely pointless 😂

@kevinaalberts9251 Жыл бұрын

Oh that sucks I see the problem already that thing wants to slide off the bead while you’re pressing down!!

@kckuc310 Жыл бұрын

What size center cone ?

@lar4305 Жыл бұрын

bolt it to the floor, you will be so much happier 😜

@tomhannockoutlaw972 Жыл бұрын

Breaker middle hole

@jeffkenyon483 Жыл бұрын

Is that a harbor freight tool?

@jeffkenyon483 Жыл бұрын

Take the valve stem core out,much easier. Other wise your pushing against the air pressure.

@adrianmack3 Жыл бұрын

I guess you missed the part before he broke the bead where there was a loud hiss due to him removing the valve core hub?

@thisone3519 Жыл бұрын

How to fix: 1. Dispose of hub motor 2. Buy a mid drive motor

@detacheddad3396 Жыл бұрын

My new hub motor spins in reverse, any suggestions?

@sean4276 Жыл бұрын

Turn it around

@guillermogarcia495 Жыл бұрын

Switch the wires

@alfredoavalosiii5448 Жыл бұрын

You have to push those outer magnets back in, after putting mileage on the wheel, they will loosen. You can apply super glue in the thin spaces in-between each one, make sure not to let the adhesive spill on anything else. Youd probably be better off using epoxy adhesive for a longer lasting fix, so the magnets stay locked into the motor.

@zeez3139 Жыл бұрын

Nice tool 👌🇬🇧

@Tight4Skin Жыл бұрын

Had the same and one of the phase wires was burnt loose in the controller. It was due to hall sensor failure in the hub motor though.

@Agnosalam Жыл бұрын

Jerky camera movements ate essence of possibly knowledgeable video

@GuleaiVasea Жыл бұрын

a phase is not of the 3

@BRENDAJASON1 Жыл бұрын

It needs a better bead breaker got mine fixed I can break the bead down first try. Watching you trying to break the bead is wearing me out

@lbermud Жыл бұрын

So frustrating to watch you try and break the bead. Hopefully you'll learn to move the tire farther away, so the breaker is not at a 90-degree angle from the rim. Suppose to push on the bead and not the sidewall. Should be able to push both sides of in one try.

@chrisrobles2012 Жыл бұрын

Okay so my new harbor freight tool broke immediately on an old tire. It couldn’t even break the bead. It slanted side ways on the second try. I see yours has a welded piece of metal bridging the gap between the two legs of the debeader.

@SamsGarage_ Жыл бұрын

Yes, I added that as reinforcement because it was so flimsy, no problem since!