Could have been a 30 second video

These claims are unjustified and can get you into a lawsuit if you're not careful

i cant get the knee bar off with the wire trick, any other suggestions?

After I ruined a few batteries I stopped using fast chargers, good old 5V 2A is good enough if you plan accordingly, the only thing those fast chargers are good for is for powering a soldering iron or some other thing that needs a lot of power but not for charging smaller batteries. I got a charger from Aliexpress with 8 USB ports, 6 type A, 2 type C, up to 30W for port and 100W total, has a screen showing the V, A, W for every port, got wireless charging on top but I don't use wireless charging.

Can anyone lead us to the buttons part number?

No teardown?

Thanks so much for the video - it was very helpful while changing our broken element.

Hello sir,why blinking red light on my Battery segway ninebot G30,please help me

Hi, does the motor still works? The second one was also from Aliexpress?

Panasonic (Matsushita) EVQ-P0N02B Tactile Switch

No electronics

I've had a couple of V10 motor pulsing moments and all of those were due to carelessly discarded panty episodes I've experienced in the past, that being said I've never doubted my V10 for a minute for I knew that it's monkey strong bowels were girded with strength like the loins of a dragon ribboned with fat and the opulence of buffalo dung.

Hello ) Please help ) I changed 2 dead cell's and now from main + and - I'm measuring 52 volt but out from the board just 5 volt ( And reset button doesn't help ( Any way to restart a BMS ?

Hi! Great solution! Soldering the extra cable seems to help on my case. The sensor was not triggering at all. After soldering, it doesn't detect my hand when approaching to the sensor, but it does when my hand leaves the sensor area. Do you have any clue? Thanks!

I progettisti Dayson sono dei DEMENTI, se metti l'elettronica a bordo motore per di più saldato insieme per i contatti portando di conseguenza tutte le vibrazioni del motore sull'elettronica, è normale che prima o poi si scassa, lo capisce anche un bambino!

How did you open it?

You dont need that plier, to remove that spring...because it's not so strong... Yesterday, i've disassambled my 8000's ... What can i say..that was dirty like the h3ll...

1. what battery to buy in case it bad later

You didn't disassemble anything you just took out the bms. How the heck do you get the plastic off safely

Thank you for video. Keep up good work. This video threw me back 10 years, but a lot has changed in the last decade. Many manufacturers have switched from pure nickel strips to nickel-plated strips or to hilumin nickel strips, primarily for perfecting spot welding in mass production and easy testing. Nickel-plated strips are much easier to weld than pure nickel, especially now that we have pocket spot welders that lack the power for pure nickel. All portable devices, electric scooters, bikes, and scooters should use nickel-plated strips due to the vibrations. Stationary devices can use pure nickel. The problem lies in the spot welding itself. Often, users weld the battery but never find themselves in a situation where they disassemble it and see the mistakes made during welding. For example, one needle might create a weld while another doesn’t. Also, if we suspect that a strip, for example 0.1x8, doesn’t have the capacity to handle the current, why don’t we double it or even use four layers to get 0.4x8? This would surely be better than 0.15x8 of pure nickel. If pure nickel were that good, the cells themselves would be made from pure nickel, but that’s not the case they usually made from hilumin - an electro nickel-plated steel strep. Our standard is 0.15x8 nickel plated steel and I adwise to you that you also use this standard for all battery production , for power tools just double or triple it.

Hey how did you wire the balancing wires? My bms came with a connector that has a jumper on it leaving only 9 wires instead of 11 *Edit: answer in the reply below.

I’m back for a second time to use this helpful info!

thanks dad

tried this and got cut twice. I guess people like me shouldn't be allowed to handle sharp objects

I have a brought a second hand AEG 8000 series T8DEM842E. It ran one cycle for two hours. Next cycle made screeching sound and then stopped. I heard the motor trying to rotate but the drum not. I opened the side and released the belt. Motor makes sound but did not rotate. Opened the motor 3 magnets were loose. I cleaned the motor and pasted the magnets back. which rotated fine manually. Now on any cycle i choose, drum rotates half round seven-eight times with 15sec interval and stops. And after 5-to 8 minutes the machine turns off. No error code. The heating Icon keeps on blinking during this process. Any Idea ?

I have a v10 and it pulsates on max…replaced motor after watching video, cleaned out any blockages and still pulsates on max?? Any ideas?

Hello everyone. Just diseambled one battery, checked how much ampeehours left - almost 3200 ah, but why does it last for a 3 days? Bateries doesnt discharge themselves, is it problem in PCB, maybe it "knows" how many cycles battery can be used? 😮

Have you tried a 9V battery? I bought LiitoKala Lii-D4XL for the purpose of charging 9V Ni-MH batteries but when I insert an empty or half empty 9V into the charger, the red charging light only appears for 5 seconds and then goes back to green and the battery doesn't charge. The batteries are new. So there is a big problem with at least Lii-4DXL models! I wonder if this one in the video works.

Hi. My battery after one year died. I would like to replace it but there is no information about type of battery. Can you help, please?

Thanks for this, simple fix and helpful!!!

My mother used to say: You guys have Blochitis!! Hey I bought the 15 pro Max. Already a dinosaur in camera terms.

LiitoKala chargers are known to report wrong (fake) internal resistance of the batteries. They are unrealiable for thus! 128 mOhm is also the maximum value LiitoKala can display.

My belt is broken, what is the best way to replace it. You're video helped me a lot to open up the dryer 👍

i ordered a couple “sony” vtc6 batteries from ali express out of curiosity more than anything! i don’t have high hopes!!! anyone ever find true high drain 18650’s on ali express?

Mine is flashing blue and won’t charge does anyone know a solution?

Mine is flashing blue and won’t charge does anyone know a solution?

nothing really new

What does a solid blue light mean?

Same here... I need to replace the motor. Once i blow with a compressor the motor noise is worst, maybe some problem inside

I repaired mine as well. Just be careful when desoldering. I pulled too hard on the old display and ripped off 3 pads from the pcb! Took me hours to fix that with wire strand bridges (like with broken trace repairs).

I can say that this soldering iron is a gem and I don't understand why they don't use them.I have a *Weller TCP 12*/12v,35W / and I don't even know how old it is but after trying it I threw all modern electronic junk/soldering irons/ in the bin.

For me it only works on maximum i dont know what to do

gratulations

I have that same new g30 controller... Xiaodash app works perfectly flashing. Only problem I've had is two of the phase wires melted together next to where they bolt to controller, I just separated them an used high temp heat shrink no damage wS caused. Xiaodash has field weakening,witch is awesome

האם יכלה להיות דרך קלה יותר למצוא היכן המתח נפסק? איך ידעת לאן להסתכל ולחפש?

has anybody has schematics of this powerbank please?

Thank you so much bro u saved my balls

My battery lights up red than nothing after that

Spring washer!

What kind of nickel did you use