Were you ever in a movie where you said "Hal...open the pod bay door please".

Thank you so much!!!!!

Oh man, that really sucks. Glad you were okay though. Are you still in the sport? I don't see any more videos beyond 3 years. I'm going for my training here in Indiana on August 3rd.

Add another successful fix. My son and I followed these instructions and started laughing when we found the exact same wire melted and broken. Thanks for helping us repair our dryer and saving the money to replace or have a technician come out for such an easy fix.

Great Video. I just have one question, does the tub have to leak as it fills or when the wash cycle starts? My tube fills up fine. No leaks. But when the wash cycle starts, I get a trickle of water from the center. This video has me zeroing in on the seal. Can I run the washer with the top and side off to watch where the water comes from? I mean how did you know where the water came from unless you ran the washer?

Thanks a million, this was exactly my same problem I wish I could give you more thumbs up lol thanks again

How long did you inflate it for? I have a weird fear of balls popping on my hand as I inflate

Does anyone know why the wire would have burnt , melted the wire in the first place. Just had the same issue, fixed it in the same way this nice fellow did, but it only lasted 3 medium heat runs before no heat again.. Haven't taken the dryer apart again to see if that same wire burnt apart again. I am just concerned of why would the wire burn apart in the first place. Looks like i have another issue that is causing that same wire to burn apart. Any ideas fellows?

Do you still fly?

I'm planning on going down there this coming winter for training. Do you remember how many flights you got in while there?

have you ever seen a 5.2 pressurize the cooling system with no misfire, no oil water mix, no combustion gas in coolant, and i blocked off egr lines? cold start up goes from 0psi to 5 psi in 1 minute,, any suggestions? maybe injector tube?

Did you have rough idle issues prior to the hard start/no start?

i really appreciate your video and helps me a lot to fix our dryer.thank you very much!

Thanks good job. I think I got it my adg. Is hard coming out?

I replaced my gasket of the same engine and the injector pulse went off what could be the problem, someone help

❤❤❤❤❤

These engines will only start if turned over very fast - they need decent batteries to provide the CCA needed otherwise they wont start

how many hours would you quote the head gasket re and re?

Where is your fuel filter located on this engine

Tried everything like levelling and loosening, adjusting screws, but nothing worked until I put a couple of thick washers in there just like he showed us. Great job!

I feel a sleep listening to this...

They suggested replacing the tub bearing as well. The bearing is more expensive than the seal but I don't want to be doing this again in 2 years

Helped me!

Do you have kit number

My Isuzu does not puling coz when I put all gears does not run fast like before

@3:32 actually that bolt actually does lift the door. Just did it to mine. That why it has a hex shape. Turn that to adjust the height and the hole its going into also has a shape that no matter how loose the bolt is, it will keep it at that height. Cheers for the video and hope my comment helps someone else.

how about having the dryer on a two wheeler and tipping it back to unhook and hook up the belt and not be on hands and knees i have a store bought knee and can not get down anymore to work like that

Common problem for this?

Showing how to use a multimeter to test would have been as big help.

This is a terrific tutorial. Dryer is 13 months old (12 month warranty) and wire was burnt. Very poor design. Thanks Jason, great video!

Why are you working outside ?

Hi Jason, I ´m trying to solve it by myself , I need to take the agitator up but It´s very hard I have seen some gays take it out by using a rope around the base of the agitator and pull it real hard out , don´t you have some other idea easier for my ´cause I´m afraid to break the plastic , warm greetins from Queretaro, Mex, and Tkank´s for your help.

Great video....thx👍👍👍

Thank you!!

Thank you so much, I pretty much had the same issue. You saved me a lot of money and time. Thank you, thank you, thank you.

Dude you talk wayyyy too much and give a lot of unnecessary information. Just get right to the point and say what fixed it.

This is nice to watch because it helps me learn how to park properly.

Hi, did you ever do that video on replacing fuel injector??

First, make sure your model is the one in the video. I spent a week getting my inner tub out with a bottle jack and 2x4. Then, chiseling the inner tub hub out with a hammer, just to find out my model, the inner tube ring gets inserted through the bottom of the tub through the drive shaft.

The door for our refrigerator has had this problem for so long, I’m going to do this, and get back to you. Thank you in advance

What if you don't have continuity from power to high and low? I dried my clothes with a jumper wire I the pocket and i found it burned up on the element.

My GE dryer stopped heating after 18 months of one load per week. Seems like they don’t make them like they used too. Thank you for a great video-I’ll try a repairman over buying another dryer

This helped me immensely and found the similar broken burnt out spade connector (actually it is a 16-14 Female Disconnect 0.250") to the heating element at the same location. The required connector can be purchased @ HomeDepot, Lowes or Harbor Freight for $5-7 (incl. taxes) for 10 / combo kit.. Loads of spares still left. After replacement of the connector, the dryer worked flawlessly. Thanks for a useful video.

Awesome video! Why don’t you have more repair stuff posted? I would watch every one!

Four years after your original post and you are still helping. Instructions on how disassemble, find the problem, fix it and reassemble were perfect. To call a service person would have cost $115 in a trip fee alone . The one part I needed came in a package of 15 and cost $5. Easy, inexpensive fix. Thank you.

Seems like everyone's purple wires are corroding and burning off... Do you think maybe it's hot moist air causing it? If so, would putting dialectric grease on that connection Help out?

Very good video keep them coming

Best how to vid I've seen so far, plus I know the dude he's a legit repair man , what up dude!😂

I’ve made this repair twice and followed every step that you said, and both time my dryer was fixed but it only lasted about a week and then the same thing happened again. Is there a permanent solution so I don’t have to keep doing this???

Ge Dryer is garbage. Broken in 15 months. Looks so difficult to open this piece of *&$@.💩