hi I have a karcher pressure washer HD7 11-4M all running well but hose and pressure gage flicking when I trigger the gun and pulsing.any Idea? many thanks

Hey man.. I have a 4400 psi Simpson pressure washer (it’s the predator 420 cc motor & EZ 4040 pump ) My machine seems like it needs to push out 1,000-1,500 more psi Do you have any advice/recommendations for fixing this?

I took out the retaining clip but the unloader won't come out. Any suggestions?

Homdapresherwasher

Mine wont go back in the ball is blocking it what do i do? Half way in i feel the needle being depress before its seated in

Hi can you please show me how to replace coupler of kitchen aid k150 blender

Thanks a lot. I have a Stihl RB600 and my local shops didn't want to mess with it. I watched your video and you fixed it for me. Thank you!

Mine broke off so clean that I can't locate the pin in the shaft. Banging it and nothing is coming out. Both propellers spin hand free

Do you work on Landa pressure washers?

UPDATE:1 year and still cranks within the first 2-3 pulls. Probably will buy another when this one finally does bite the dust kzfaq.infoUgkx43QMbQqu67IZadu9ou8Sg1BdrunMRNqX . No issues at all. Very happy with it.UPDATE: After 6 months of use and over 70 uses I would still highly recommend this pressure washer. It does vibrate a decent amount but never had it “walk” like others have mentioned. No oil leaks, still seems to run like the day I bought it. Still cranks within 2-3 pulls every time. Very happy with my purchase!Have used it about a dozen times now. Plenty of power, cranks up on 1-2 pulls every time. My only complaint would be I wish it was a little taller to make it easier to walk with it (hits my ankles a lot) and that the two hose connections were a little further apart but it hasn’t caused me any issues. Seems to run a good 1-1/2-2 hrs on a full tank, overall a well built machine and definitely worth the money in my opinion.

UPDATE:1 year and still cranks within the first 2-3 pulls. Probably will buy another when this one finally does bite the dust kzfaq.infoUgkx43QMbQqu67IZadu9ou8Sg1BdrunMRNqX . No issues at all. Very happy with it.UPDATE: After 6 months of use and over 70 uses I would still highly recommend this pressure washer. It does vibrate a decent amount but never had it “walk” like others have mentioned. No oil leaks, still seems to run like the day I bought it. Still cranks within 2-3 pulls every time. Very happy with my purchase!Have used it about a dozen times now. Plenty of power, cranks up on 1-2 pulls every time. My only complaint would be I wish it was a little taller to make it easier to walk with it (hits my ankles a lot) and that the two hose connections were a little further apart but it hasn’t caused me any issues. Seems to run a good 1-1/2-2 hrs on a full tank, overall a well built machine and definitely worth the money in my opinion.

Hero

Have a simpson PS60841, have to keep the wand trigger pulled back all the time to keep it running. Took the unloader valve apart and replaced some o rings so as the spring loaded adjuster would slide back and forth. Then inside the port in the spot where the two orings are on the unloader valve is a small port that goes back to the discharge where you connect the hose for the wand. This small port was plugged, used a hobart tip cleaner which uses tiny drill bits. Found tip cleaner at Northern tool. Also used some .035 hard welding mig wire to clean out this small port. You will need a flash light to see it.

Answer your phone lol

Tengo una maquina dewalt de 4000 psi y la bomba AAA 53brd35 tiro el aceite con agua por la parte del nivel de aceite Que puede ser el problema ?

my unloader doesn't want to go out I tried everything I got Ryobi 2800 psi maybe in this model this unloader should stay in? nah that would be stupid

Worked like magic on my Homelite. Thanks for the easy fix!

Pamp paresr hed price of

Mine is leaking at the brass nipple next to the unloader valve. Ball moves freely and spring loader valve moves freely. Any ideas?

Salut, pardon comment gérer l'eau lors qu'elle au niveau du tu trou située au déçu du réglage de pression

I like to know if we can adjust the unloader valve

where do you find the part number for the pump

What to do if you can find the hole to punch out the pin?

Thank you Chris! Fixed my problem at no cost. For the record, I have a different Craftsman unit and the U clip is under the valve rather than on the side. Same principle though.

Hi! I’m having a problem with the pressure washer engine dies when I unsqueeze the trigger for the wand on a Simpson pressure washer with Honda engine What do you think the problem is?

Very useful video

Thank u my friend!!

I have a pressure washer with honda motor, I didn't use it very often but last time I did, soonest I release the trigger on the gun the motor just shot off... So what I have to do it's just keep pushing the trigger all the time... Any idea what I can do? Thanks Raudel

I have Troy-Bilt 2800 2.3 gallons, I used the pressure washer a couple of weeks ago with no problems went to use it this last weekend and no pressure? When hooked up the and the engine not running water flows through the hose and wand just fine start the engine and no pressure, can you give me some ideas of what the problem is?

Nice tutorial cris

Cheers Chris

All I did was replace the spark plug. Works like a charm 🙏🏻

This would be great if my Ryobi wasn't so old. I got it for free from my buddy, so NOT complaining. It was leaking like nobody's business and came with a wand that couldn't be taken apart. So, I got a wand, nozzle and 5 tips on ebay, then a hose from Wal-mart. Fired it up....NO PRESSURE! Watched this video, the clip broke..had to take the assembly apart...got the clip out, but that darn unloader will NOT come out. I think it's rusted in there! I'm gonna keep trying...and yes I've sprayed it WD-40...ugh!!!

You hit the nail right on the head for what was wrong with mine thank you thank you for your video keep up the great work

Mine was free, do you have any other suggest. Mine will sometime have pretty of pressure then other times goes to low pressure and won't come back up.

Thanks. you save me some money I check that and I fixed that was the problem

Excellent

Have Dewalt 3800 with 53003 pump much like in this video. Has been used only few times then pressure dropped to around 1/4 pressure and only minimal strain on engine when reaches that point . Installed new seal kit (no change) unloader seams fine ???

Thanks Man, this really helped me

Buen día me gusta pero no entiendo del todo el idioma. Saludos bendiciones

Thanks for posting this. It sure saved me some time and frustration!

Thank you very much, this was exactly the problem. I was about to trash my washer

Thank you for this video, i fix in 5 min

Looked at mine and still doesn't fix the issue.

LOL Guarantee repair. They will bandage the pressure washer until the warranty runs out, then they will offer the owner a new pump.

I did everything but the little clip just won’t go in. No mater how hard I hammer it, it just won’t go in and now water is coming from it. I paid $114 two days ago to get it fixed and the guy didn’t even saw this. Motor starts, no water coming from the nozzle.

you're the second dude that said this,,...IT'S NOT MY fuckin problem......gonna keep looking for an answer....damn DeWalt

Hi . Last year i purchase a new pump and it work fine so i didn't used anymore, so coming this spring time i needed to used it again and for my surprise the engine start to stall when leaving the trigger, i proceed on checking the unloader valve which was working fine now i don't know where to go from here. Any help is much appreciated. Thank you.

How funny, I was born & raised in Kings Park. Right off of 25A at the Sunken Meadow Beach exit. Thank you for the informative video

When I pull the trigger there is pressure but if I keep the trigger pulled the pressure dies. Is this also an unloader problem?