For someone like me who looked really hard for that cable and couldn't find any, look harder. Mine was stuck on the really far end of the door, I had to reach quite deep and pull on a cable and then I was able to roll the window fully down, I just ziptied the cable through one of the holes and that fixed the issue for me.

Is this valve only on petrol cars and not diesel ?

Thank you

wish I watched this before waxing my car this morning! Will definitley use your method, as I couldn't believe how hit-and-maiss and wasterful the rinse-off method was (not to mention lucrative for the manufacturer). Great vid!

Thank you so much for this video. I have a 2009 Ford fusion and it looks the exact same. I'm a single mom and was told that in order to switch my ignition switch is be charged anywhere from $125 to someone told me $250. I bought the ignition switch for $35 and replaced it within 10 minutes because of your video. You saved me sooooo much money and the video was so clear and accurate! Thank you so much! This was the best!

Amazing & Very Detailed Video!

I appreciate your concern for the environment and unnecessary waste of product.

Good video. Only thing I do different (if I wasn't going to bleed the whole system) is to loosen the bleeder screw before compressing the piston, to bleed out the worst of the old brake fluid. Then, of course, top off the master cylinder.

How do you vacuum it?

If you take the oil cap off as it's doing it and it goes away it's the valve cover

That noise may have went away for a little while but that's your valve cover needing to be replaced there is a valve built in to the cover and it's sucking air through it. Had the same. Issue

Yeah I have that same. Noise I bought two brand new ones twice when I replaced them that noise started after 15 seconds of idling but it was much quieter. Never actually fixed my issue but of course I bet it does in this video. My camshaft position sensor code p054b is on. Not to say that another code won't come on but I'm going to at least replace the camshaft sensor. I'm sure it won't fix it either my fuckin luck. What are the odds of having 2 brand new ones making it actually worse??

Lmao can't hear ya bro

May the coolant leak from the oil cooler housing on these cars? Thank you for your help.

This foo on a sick one

Just what I needed to understand. Brilliant vid. Thank you, fine man.

Just did this job on a 2001 Toyota Solara. Thanks for the video!!!!

Thanks for your reviews. Heading there Friday!

Total garbage, it is not comparable to Kingsford in any way shape or form. It turned into ash within 30 minutes so we couldn't even finish cooking and, that's 15 min to reach cooking point and it turned into ash within another 15 min. The Kingsford stays lit for about 2 hours and we usually have to shut it down because we're done cooking.

Super advanced lol

May i ask how you add PAG oil to the compressor? Is it through the HI pressure or directly through the compressor? Or both?

I've got the same problem. I have a Nissan Qashqai 2.0 Dci 2008 J10 car with an automatic gearbox. I can feel vibrations inside when I turn it on. I've changed all engine mounts, only thing I haven't changed is the gearbox mount.Questions When I'm at Neutral or Parking gear, is it possible to experience vibrations from the gearbox if the mount is too worn out? When the car engine is ON, but the car is at Neutral or Parking gear, does the engine transfer rotation power to the gearbox or does that only happen when I turn to Drive gear? From reading online, these is what I got: Yes, it is possible to experience vibrations from the gearbox when the vehicle is in Neutral or Parking if the gearbox mount is too worn out. The gearbox mount is designed to hold the gearbox securely in place and to absorb vibrations and shocks. When it becomes worn or damaged, it can no longer effectively dampen these vibrations. When the car engine is on but the car is in Neutral, the engine is running, but the transmission is disengaged from the drive wheels. The input shaft of the transmission might still be spinning because it's connected to the engine, but there's no power being transferred to the output shaft that drives the wheels. Essentially, the power flow stops within the transmission, meaning the wheels do not receive any torque.

Thank you!!! Should I wear worried about torque specks when tightening with a wrench, or just tighten until it’s tight?

Just build a platform for the back to level with the seats folded down and you are done. Why carry so much unnecessary items to make it flat.

Thanks sharing

My bestest friend just bought a second hand compresser for his antique 520i, you made it look super simple but he’s a total fucktart gimp, would you advise that he does it?

Can we use wd40 instead?

Acetone will remove those stains, but only do that if u plan on selling it😂 the leather will start to crack within a couple weeks

What year is this car? Pretty much the same as a 2007?

What year

Do you know where can i find the ECM in the Volt I guess it would be something similar to HPCM?

whats the difference when replacing this and the ignition cylinder? Wouldn't they both cause similar issues.

So you only have to disconnect the battery in the back right?

Where is the gasket you replaced ? You didn't show it?

Been there--not fun when you need to dump that weight somewhere!

Thanks so much for posting this. Other videos I've seen were not specific to the 2005, so I wasn't sure what to do once I took the wheels off. Big help! I'm replacing the rotors, too, but will have to put off changing the brake fluid till next week... Subscribed!

I recomend you this: when you mention a vehicle write first the year. Car name.engine zize. And part you are working on..please tanks so much

This was a great video ! Bravo !

How much would be the speed sensor

Thanks. "New" C-Max for us, hard to find older car electronics references.

Did this and now the car will not go into gear unless it is off.

Yep it's made by Royal Oak.

Thank you very much this video help a lot 🙏

I cant get the screw to go back in the lock what am i doing wrong?

Bright young man, good tutorial

Animal crossing voice when it goes fast motion lol e

I dont think this will help i just put a new throttle body on an 02 buick century and the gas pedal is stuck will not move and i dont want to force it

I had the same noise but at random times at low speed. I changed both VANOS solenoids, and changed the whole drive belt kit including the alternator's pulley and still have this noise at times.

i have this exact same problem on my model x, i originally thought it was the 22 inch wheels but it is also affecting your car...

thank you, solved my problem with shuddering under load. (: