Where can you get the Test Card. I am not seeing it in the down loads area. I ordered the K40+ should be here this week and want to get my Lightburn test files set up for when it comes.

Where is the test card file for LightBurn? I'm not seeing it on the link provided.

Hi , I love this video! If’s not too much to ask, where did you buy the mirror acrylic sheets?

Love your guys' products. One little tiny thing was broken when it arrived, but didn't stop me from lasering. I had my new lock assembly for one of the panels within a week. Been loving it since. This last year with the machine has been awesome. Ok,now time to actually watch the video ...

Where do I get the driver?

Thank you

Don't have a Galvo, but great video, Murphy 🤙

Damn, they dont answer questions on their own videos? I will be looking elsewhere.

What is the smallest font the machine can engrave and still be legible?

I have just installed the Omtech 4 wheel rotary and had no luck with the setup proceedures as described by several videos, all different steps. finally i gave up and contacted Omtech, the answer they gave me worked first time and is repeatable. I recognise that your machines firmware may be older than mine so things will have changed. My machine is an Omtech 50W Blue BED 300 X 500 with Ruida control, firmware version RDLC-V8.00.70 My initial steps:- Step 1 - In XY mode, home the machine to X0 Y150 (bed size is 300 x 500) Step2 - Power OFF!!! Omtech's instructions start here:- Step 3 - replace the Y cable with the Rotary Cable. Step 4 - Power ON and wait!!! The rotary machine tries to HOME, this is OK, DO NOT stop the process, WAIT, it will spin in both direction slowly, i assume to search for HOME, then it spins fast and Zeroes the Y and keeps the X setting. for me it is 150. There is no need to disable the XY homing tabs, as has been mentioned in other videos, this defeats the purpose and is against Omtech's instructions. I use Lightburn as my interface, now I install the Rotary settings that I have previously saved and adjust the Rotary setup as necessary. When I am finished with the Rotary and before i power off, I reinstall the default XY settings from my saved file and shut down. When I next power up the machine resets to the default XY position. It is important to save the default settings before you do anything to that file. I saved the Default file to my desktop .. I load a modified file for the rotary, when i need it, that i have also saved to my desktop. I hope this helps others as i know this can be frustrating.

Do you put any liquid to the magic eraser?

I am having about a 50% failure rate with this product and Cermark. 100w laser running 300mms/50% power. half the parts some portion wipes right off. the next part will be fine. Next one some wipes off. very frustrating and expensive as the parts I am doing are costly and ruined. I am carefully cleaning before spraying. Any advise?

That’s wild I do 350mm/sec at 10% power on my 60 watt. I wonder why you need to use nearly twice the power and way slower than mine.

Very interesting

This beast looks sooo good🔥🔥🔥 Love you OMTech❤

where can I see one in action?

Posso avere il nome o la marca della macchina laser ,grazie?

What happened to the "up to 1000mms engraving speeds"? 36% faster isn't much

Assuming the new tech works as well as old, and isn't encumbered by ridiculous DRM or needing an internet connection like the buttheads st Glowforge, this looks awesome. That said, you'll have to fight to ever let me get rid of my old couple year old 60W from them. During those horrid lockdowns, prototyping stuff with my laser really kept me going. Also, tech support was absolutely amazing. I only needed a little thing and they were super awesome and got it to me within a week. There was a broken lock if you're curious what it was. Once I get a new house, I cannot wait to order a newer laser from them.

Is that a Thunder Laser?

Wooooopaaaa !!!

What is the operating voltage of the Water Sensor

honestly, the easiest to follow focusing video I have seen and the fastest. Just enough information to do it correctly and not enough to confuse the viewer.

I hope when you used that sandpaper on the stainless steel you were wet sanding with 1200, or 2000 grit paper. If you had scratches left on the piece then I'd say it was likely you had to coarse a grit.

Great video. I'm waiting on some mirrored acrylic to arrive. I did some tests on two tone (multi layered) acrylic samples. Unfortunately, you could see lines in the filled areas. Is it likely that I'm running it too slow/strong? Any suggestions would be very welcome

Is the laser also available in Europe (Germany)?

Can i cutting mirror acyloc with diode laser?

Any chance to review in Italy

What are the dimensions it can cut?

Running on 1.5mm basswood. None of the images are burning in.

where is Brilliance Laser Ink

What's the Pen function? And how do you determine the Y Axis?

so dumb question. can i use dollar tree faux leather?

👋

What is the camera attachment?

I just bought this machine and when I went to do the Pulse test, the laser did not work at all. We followed the setup instructions but the laser won’t pulse at all. Are we missing something?

My Omtech 70w will do nothing under 14% power. How do we do 10% power exactly?

Where do you buy this part?

Well done guys hopefully to review soon

We own an Omtech (AF2028 60watt) machine and use it for our business. Having worked with lasers for the past decade using high-end lasers (universal, epilog, trotec) along with cheaper Chinese models similar to Omtech, I can say customer service is a must. That said, every time I have had to reach out to Omtech support, I have had nothing but issues. The tech support has never had the information I needed, and it's super frustrating. How do you not have the specs on how much weight you can set inside your machine? All-in-all, the machine is a great starter machine, but if you are trying to buy one for a long-term business, I would recommend a company with better support. Although this is a negative overall review, no one ever wants to mention this and only talks about the positives. Transparency should be a must when customers are trying to buy and spend thousands of dollars regardless.

Ordered a 50W Fiber during the Memorial Day sale and is gonna be here any day now: Super excited to up my laser game!

Can we have more videos like this

What kind of lights did you add to your laser?

los videos no los tienen en Español ?

What is the model number of this Ruida controller? Pls as I also have the same controller but I don’t know the model ,

You said once finished with the rotary you have to reset your machine how exactly do you do this please

Sorry spelling WHICH LASER MACHINE

Which kaser bachine

I was looking at your video , and I have a question how can I change the work area size on the control panel

is this test card also good for acrylic?