What fluid did you use to soak the clutches in and what kind of sealant did you use for the case? Going to do an Clutch on my 2002 CBR 954RR and any advice would be greatly appreciated

Installing Heli bars is harder than this just takes time n patience n organization skills no big deal great video👍

John Talley.. the GOAT

Anybody have a good place to buy the wrap around bar that goes on the rear rack? Great video

I have symptoms of both lean and rich Uneven acceleration & bogs - rich Surging at 1/4 throttle - lean Runs better cold - rich Backfires as loud as a rifle - lean Spark plug a little black but looks normal No smoke A little bit of soot in the valves Carburetor has the slide needle dropped all the way down I’ve been chasing these symptoms for 9 months now and haven’t found the issue Did a carb clean, replaced the petcock, new air filter, spark plug, the motor is hardly broken into. 3,900kms, so the jets in the carb are brand new and clean. The motor is in time as well I took it to a few mechanics and they don’t even know what’s wrong

After you change the oil, and while running, I would keep the side cover off so you can make sure there's no leaks after reinstalling the oil filter cover.

Thanks bru. I will try this hack today

Foot brake is doing not much. Cannot find anything on this. Help?

As usual John is awesome...I learn something every session he does!

🇸🇦👍

How do I stop front sprocket from spinning when tightening? Even with someone holding the brake still spinning

Is this the same thing for Honda shadow 2008 vt750CA?

Does this also apply to a 01 R6?

Buen dia, tengo una yamaha yfm400, funciona por 20 segundos y se apaga, se corta la chispa de la bobina, le dor marcha y funciona otras 20 segundos y se apaga de nuevo, así es lo único que hace. En un principio le cambie de cdi porque estaba peor ni encendía, solo funciona ese corto período, gracias quien me pueda ayudar.

A lot of work and not for the shade tree mechanic. Like you said there is a lot more work to do.

What year is it from?

Would JB weld work with time sert , i know theres more mass but wouldn't the excess be able to get threaded

So at the end of the day which has better torque, sheer, pull strength? Also if a blind hole was deep enough could you use a timesert over a heli coil any issue with this besides cost and overkill

Looking good John 👍

👍🇸🇦

Which hoses go where on the IAC valve? I was thinking rear throttle body hose goes to the top of the IAC but wanted to check. Thanks.

I watched this vid hoping to see some clever solutions to oil leaking all over the place when the filter cover is removed. Instead, the tech seemed completely unconcerned with spillage. I made a funnel out of aluminum foil and that helped.

Hello there… thanks for all your videos… have one question, you know the reason The ABS light on in my CBR 1000rr 2008.. and how can I fix it??

Here's hoping I can do all this with basic hand tools and a dream reeee

I can't get no power to the dash screen

dont see where you mentoned that the bke should be uprght, rather than leanng on the sde stand ?

Добрый день. А у вас есть отдельная папка или что то по honda crf 450r ( 2008г) . А то у вас много видео,трудно искать))

Is there supposed to be a play on the front sprocket after torqueing the bolt?

My exhaust smells like rotten eggs especially on startup

So is it 10w30 or 10w40?

you do a great job in your video. Easy to follow, and pleasant to listen to. Thanks for bringing confidence to doing this job DYI. Who would think you needed that level of disassembly for an air filter!!

Does this oil change have to done on my Stratoliner ??

For people from another planet : Drain plug torque - 29.8 Nm (22 Foot Pounds) Oil filter torque - 16 Nm (12 Foot Pounds)

Mine turns over but just won't start green light is on but doesn't seem to be firing r get spark but if u hold spark plug wire my son it was getting spark not sure though what else could I check

Hello, I have a used 2005 Sportsman 800efi. Replaced the fuel pump it stopped working while doing that I also changed the Injectors and plugs now it just doesn't sound as it should. Top end running it was back firing a little. Did the Fuel Injectors get crossed by any chance ? Before I take apart again.

What's the most expensive part in a motorcycle? How do I take care of it not to get spoiled

Is there importance in selecting which caliper to bleed first on the front? Left or right?

Yellow red under headlight

Looking good John 👍

Is all the torch specs the same on newer models?

Well. I installed my piston rings all wrong. It is still running fine though.

Love the 350 content

Thanks for the advice n also your glasses cought me off gard havent seen a magnet center before

Tried to bleed my father inlaws rear brake but could not get the pedal stiff, now I know why ….

Clutch plate

Mine does the clicking right now when I try and start it but won’t start. It’s a 2008 rancher 420, do you think it would be the starter since the solenoid still clicks?

Great video. Simple and to the point. Very helpful to maintain my 2020 850 Trail.

thanks brothers for the great how to's!

What about torque digital adapter?

What a joke he lists wrong chain breaker. It doesnt work, its not the one hes using in video found out the hard way!!!